International Interzinc 52 (Winter Grade) is supplied with a winter grade curing agent to enable more rapid cure at lower temperatures. A two component, metallic zinc rich epoxy primer which complies with the composition and performance requirements of SSPC Paint 20.
Rust-Oleum 6400 Fast Drying Shopprimer
A fast drying, solvent based, anti-corrosive primer for temporary metal protection intended as the first coat in shop coating applications and provides the required basic protection following metal fabrication and assembly operations.
Rust-Oleum 6400 Fast Drying Shopprimer is a fast drying primer based on a soya oil alkyd. The products contain rust-inhibitive pigments and are lead and chromate free. Rust-Oleum 6400 Fast Drying Shopprimer should be applied on cold-rolled, blasted, pickled or slightly rusted steel.
Rust-Oleum 6400 Fast Drying Shopprimer is primarily intended for spray application but may also be applied by brush or roller for touch up or small areas only. Rust-Oleum 6400 Fast Drying Shopprimer can be recoated with the Rust-Oleum Alkyd Primers/Intermediates and the Rust-Oleum Alkythane 7500 System Topcoat assuring the appropriate protection at light industrial exposures.
- Up to 1 year corrosion protection outside
- Ideal for construction, storage and transportation
- Masks construction deficiencies
- Ideal for spray application
- Lead- and chromate free
- Recoatable with Rust-Oleum CombiColor and other coatings
Please note: Remove grease, oil and all other surface contaminations by alkaline or high pressure (steam) cleaning in combination with appropriate detergents.
- Typical Coverage (per coat)
- 12m² per litre
- Touch Dry
- 1 Hour
- Brush, Roller, Spray
Be the first to ask a question about this product!
Sika Poxicolor Primer HE NEW is a high solids, surface tolerant, epoxy primer coat for steel and galvanized surfaces. A 2-pack primer coat based on epoxy resin, economic and high performance corrosion protection also for manually de-rusted surfaces.
International Interlac 497 is a one pack alkyd undercoat for use on internal and external areas above water on marine vessels. International Interlac 497 is for use at Newbuilding, Maintenance & Repair or On Board Maintenance.
Sherwin-Williams Transgard TG116 is a two pack epoxy undercoat for abraded surfaces. It is used for application onto suitably primed surfaces, as an undercoat for use under suitable high performance finishes.
This Jotun Paints product is a high solids, very high zinc dust content primer for highly corrosive environments and can be applied down to 0°C surface temperature. Jotun Barrier Plus is a two component polyamine cured zinc rich epoxy coating.
Jotun Penguard Express MIO is a two component amine cured epoxy coating that is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high build product. Specially designed for new construction where fast dry to handle and over coating times are required. Can be used as a primer, mid coat, finish coat or as a single coat system in...
A high build coating for the protection of structural steelwork against corrosion that can be used as either an intermediate, or finish coat in interior and exterior environments.
Teamac Rust Converter is an excellent product to stop the rusting process and allow rusty surfaces to be overcoated: Easy to apply, and ideal for marine and industrial applications Can be applied to rust in existing damp conditions Suitable for rusted iron or steel Application by brush, roller or airless spray To be overcoated with a primer or...
Sherwin-Williams Macropoxy C400W (formerly known as Epigrip C400W) is a multi-functional epoxy zinc phosphate coating specified for use as a primer on blast cleaned structural steel for internal and external environments. Sherwin-Williams Macropoxy C400W may also be used as a high build intermediate coat as well as the final coat where a low sheen...
An inexpensive primer based upon iron oxide for use on structural steelwork, iron and metalwork which can be left as a short term finish or overcoated with Teamac Marine or Industrial coatings.
An all-round excellent choice for the temporary protection of steel exposed to highly corrosive environments. Muki Z 2001 from Jotun has a solid track record and a reputation built on satisfied customers in a range of industries and countries worldwide. Jotun Muki Z 2001 is a two component inorganic low zinc moisture curing zinc ethyl silicate coating...
Sherwin-Williams Zinc Clad J984BS (formerly known as Epigrip J984BS) is a 2-pack epoxy zinc rich anti-corrosive protection primer for steel surfaces prepared by abrasive blast cleaning. It may also be used as a repair primer for galvanised surfaces.
Sherwin-Williams Zinc Clad II EU is a self-curing solvent based, two component zinc silicate coating for the protection of blast cleaned steel surfaces. It is capable of withstanding temperatures up to 400°C and of curing at temperatures down to 0°C.
International Interplate 855 is a fast drying, two component, weldable zinc silicate pre-fabrication primer for application by manual or automatic spray used as a temporary protective primer for the coating of steelwork prior to the fabrication process.