Sherwin-Williams Mordant Wash L703 (formerly known as Leighs L703/Transgard TG155) is a blue mordant solution for application onto galvanized surfaces as a chemical pre-treatment to improve the adhesion of subsequent paint systems.
Teamac Micaceous Iron Oxide
A high build coating for the protection of structural steelwork against corrosion that can be used as either an intermediate, or finish coat in interior and exterior environments.
Teamac Micaceous Iron Oxide (MIO) is a high build coating for the protection of structural steelwork against corrosion. It can be used as either an intermediate, or finish coat. For use on cranes, transmission towers, bridges, lamp posts, railings etc. Its thick anti-corrosive film is extremely effective in prolonging the life of these types of structures.
Teamac Micaceous Iron Oxide provides protection to steelwork exposed to weathering. Can withstand temperatures up to 99°C and could therefore can be used in a system for medium temperature duties. Ideally it should be used in a full painting sequence with anti-corrosive primers.
- Thick, anti-corrosive layer
- Resistance to temperature and weathering
- Exterior steelwork protection
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Typical Coverage (per coat)
- 5m² per litre
- Touch Dry
- 2 Hours
- Brush, Roller
Be the first to ask a question about this product!
Nullifire PM018 Primer or Top Seal Epoxy Coating is a two-components modified epoxy coating. It is a heavy duty, high build coating for protection of steel in corrosive environments and is excellent for use at low temperatures.
Sherwin-Williams M600 (formerly known as Leighs M600) is a quick drying single pack alkyd anticorrosive primer pigmented with zinc phosphate, used for the protection of steel where speed of drying is important.
A fast drying, water based, anti-corrosive primer for temporary metal protection intended as the first coat in shop coating applications and provides the required basic protection following metal fabrication and assembly operations.
Nu-Steel TP Aluminium Primer is an epoxy-based coating, for use on properly prepared steelwork, such as parapet/guard rails, bridges and architecture. Advantages Metallic Aluminium finish. Touch-dry in 3 hours. 8m²/Litre average coverage. 12-month shelf life.
Nu-Steel Zinc Rich Primer has been specifically-formulated to prime mild steel surfaces to prepare it for overcoating with the finish of your choosing. Steel with low carbon is termed as mild steel, and such uses of this type of steel include: signs, furniture, fencing, cars and structural steel. Advantages Interior and exterior use. 3-5m²/Litre....
Nullifire PM021 General Purpose Epoxy Primer is a two-components epoxy polyamide primer with excellent resistance to salts, water and alkalies, and with very good resistance to mild acids and solvents.
Rust-Oleum 3202 Galvinoleum Primer is a single pack super adhesion primer for galvanised steel, plastic or other smooth surfaces. Should be used on galvanised steel, stainless steel, aluminium, copper, glass, porcelain and other smooth, dense surfaces. Only intended for brush application and can be recoated with Rust-Oleum 7500 Alkythane.
A fast drying reputation isn't all International Intercure 200HS is renowned for. Complete with MIO, this Fast cure anti-corrosive primer/intermediate with added barrier protection, can improve your productivity and lower your solvent emissions.
Rust-Oleum 769/780 Damp-Proof Rust Primer is a single pack rust primer for direct application on slightly moist or dry metal surfaces. Rust-Oleum 769/780 Damp-Proof Rust Primer is specially developed to be applied on hand tool prepared sound rusted steel surfaces.
Jotun Penguard Express is a two component amine cured epoxy coating that is fast drying, high solids and high build. It is specially designed for new construction where fast dry to handle and over coating times are required. Can be used as a primer, mid coat, finish coat or as a single coat system in atmospheric environments.
A primer from Rust-Oleum to make difficult smooth surfaces coatable. CombiPrimer Adhesion is ideal for use on galvanised steel, stainless steel, aluminium, copper, glass, porcelain and other smooth, dense surfaces that normal paints cannot stick to.
An epoxy primer excellent anti-corrosion properties this primer is the perfect choice for steel and iron gutters or any other steel/iron surface. Top Features Good anti-corrosion properties Brush or airless spray applicable Application temperature from +5℃ (substrate)
Rust-Oleum Hard Hat 2185/1085 Galva Zinc is the No.1 high zinc content coating providing superior protection and durability for metals exposed to the elements or adverse artificial conditions. Can be used as a primer or as a single coat in light industrial exposures, corrosive environments and high humidity areas. 90% zinc content, touch dry in just 15...
SikaCor 6630 Primer is part of the SikaCor 6630 System which is a low-solvent, oxidative drying high-build coating with active corrosion protection pigments based on modified synthetic resin combination. SikaCor 6630 Primer is mainly used in case of manual de-rusting preparation or maintenance is being carried out on existing systems.