A specially formulated blend of solvents designed to mix with its compatible Teamac or Coo-Var coating to create an optimal consistancy for application. Suitable for use with Brush, Roller or Spray. Teamac Thinner 14 can also be used for the cleaning of some surfaces prior to application of the coating. Also suitable for the cleaning of...
Coo-Var Anti-Corrosive Red Oxide
Coo-Var Anti-Corrosive Red Oxide is a strong alkyd based red oxide product that can be applied directly to the metal surface. It is a general purpose primer and finish in one coat. Easy to use and it offers excellent protection.
- Primer and finish in one
- Can be over-coated at a later date
- Apply direct
- Protects and decorates
- Rapid dry version available
Coo-Var Anti-Corrosive Red Oxide is a strong alkyd based red oxide product designed to be applied direct to the metal surface. It is a general purpose primer and finish in one coat.
Its uses include structural steel, general metalwork, tanks, iron gates or pipes. Can be left as a finish or overcoated at a later date.
Ensure all surfaces are clean, dry and free from grease, oil and any other contaminates. Bare steel should be free from dust, rust and scale. Blast cleaning to SA 2½ is recommended. If blast cleaning is impractical, mechanical cleaning should be employed as hand cleaning does not clean the steel to the required degree.
Any oil or grease should be removed with Coo-Var Degreaser before de-rusting. Where blast cleaning is carried out after assembly, special attention must be paid to edges, corners, nuts, bolts, welds etc. Welds should, if necessary be ground and all weld spatter, slag etc. must be removed.
As dictated by normal good painting practice. Care must be taken during application that the temperature is above the dew point to avoid any contamination. In confined spaces, provide adequate ventilation during application and drying.
Can be applied directly to prepared iron or steel, for greater protection prime with Coo-Var Zinc Phosphate Primer.
Coo-Var Anti-Corrosive Red Oxide or other suitable topcoat.
- Structural steel
- General metalwork
- Iron gates
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Water / Solvent Based
- For Use On
- Steel, Iron, Metal
- Application Method
- Brush, Roller, Airless Spray
- Single, Two or Three Pack
- Pack Size
- 1L, 2.5L, 5L
- Base Type
- Alkyd based
- Dry to Recoat (at 20°C)
- 12 hours
- 13m² per litre
- Recommended Thinner/Cleaner
- Thinners 14
- Solids by Volume
- Touch Dry
- 5 Hours
- Recommended Dry Film Thickness
- 35-40 microns
- Recommended Wet Film Thickness
- 75 microns
- UN Number
Be the first to ask a question about this product!
Coo-Var Universal Degreaser Cleaner is a careful blend of solvents to give powerful cleaning and degreasing properties. Product Features Degreases and removes oil patches from floors, walls, interior and exterior surfaces prior to acid etching or painting. Part of the cleaning process. Essential for a good finish. Can also be used as a...
Coo-Var Zinc Phosphate Primer is a high performance, modified alkyd metal primer. It has very good anti-corrosive properties. Its high durability makes it ideal for use in coastal areas. Product Features Ideal when wood and metal are combined in the same structure as it will prime both surfaces A stronger primer than most basic DIY...