Makes the smoothest surface coatable! Rust-Oleum 3302 CombiPrimer Adhesion should be used on galvanised steel, stainless steel, aluminium, copper, glass, porcelain and other smooth, dense surfaces followed by Rust-Oleum CombiColor Original or Rust-Oleum CombiColor Multi-Surface.
Rust-Oleum 3302 CombiPrimer Adhesion is for use on galvanised steel, stainless steel, aluminium, copper, glass, porcelain and other smooth, dense surfaces that normal paints cannot stick to. CombiPrimer Adhesion should be brushed onto a surface and after 30 minutes needs to be overcoated by either CombiColor Original or CombiColor Multi-Surface as soon as possible. This is to ensure that no dirt or dust gets trapped on the tacky surface and ensures maximum adhesion.
Also adheres to aluminium, stainless steel, aluminium, copper, glass, porceilain, and other smooth dense surfaces etc.
To recoat after 30 minutes
Transparent blue appearance
Very high coverage, with theoretical consumption of 50m² per litre
Technical
Density: 0,92
Solids content in volume: 20%
Heat Resistance: 100°C (dry heat)
Drying Times At 20°C/RH 50%
Touch dry: Remains tacky
Dry to handle: Remains tacky
Dry to recoat: After ½ hours but within 24 hours
Application
Recommended Wet Film Thickness
20 µm
Recommended Dry Film Thickness
2 µm
Consumption
Theoretical: 50 m²/l
Practical: Practical coverage depends on many factors such as porosity and roughness of the substrate
Surface Preparation
Remove grease, oil and all other surface contaminations by alkaline or high pressure cleaning in combination with appropriate detergents. Remove previous coatings completely. Remove salts, 'white rust', etc., by washing with Rust-Oleum Surfa-Etch 108 Etching Solution. The surface must be clean and dry during application.
Directions for Use
To ensure homogeneity, coating materials should be thoroughly stirred prior to use.
Application Conditions
Temperature of air, substrate and coating material between 5 and 35°C and relative humidity below 85%. The substrate temperature must be at least 3°C above dew point.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Hi I want to colour code my car bumpers using combi colour . Is this primer ok to use on them . Also is there a flexing agent I could use ?
Answer from Rawlins’ Technical Team:
There is not a flexing agent available of Combi colour, but you could consider Rust-Oleum CombiColor Multi-Surface as this is suitable for most plastics without a primer and is inherently flexible already.
sarah nicholson on 2020-03-26 16:46:01
Question:
I have some old galvanised water tanks which are rusty inside. I want to put soil in them & then plant them up. I have used a drill with wire brush to remove all the flaking dirt & rust inside but what should I paint them with please before filling them (they will have holes in the bottom) - and how long will I need to leave it to dry please. Thanks in advance
Can this be applied direct to new mill finished aluminium sheeting or would you need to prepare the surface beyond cleaning and degreasing it? Thanks
Answer from Rawlins’ Technical Team:
Rust-Oleum 3302 CombiPrimer Adhesion should be used on galvanised steel, stainless steel, aluminium, copper, glass, porcelain and other smooth, dense surfaces followed by Rust-Oleum CombiColor or Rust-Oleum CombiColor Multi-Surface.
Remove grease, oil and all other surface contaminations by alkaline or high pressure cleaning in combination with appropriate detergents. Remove previous coatings completely. Remove salts, 'white rust', etc., by washing with Rust-Oleum Mathys 108 Surfa Etch Solution. The surface must be clean and dry during application.
chris on 2018-10-26 17:53:48
Question:
i need to re paint my 25ft aluminium boat , some areas need priming others just painting , i also require an antifowling paint for the hull any sugestions , many thanks chris
Hull – Remove all loose and damaged existing coating and all marine growth. High pressure wash with fresh water. Do a test area with Teamac Metaclor Underwater CR Primer to ensure compatibility with existing antifoul. Abrade bare aluminium and spot prime immediately with Teamac Metaclor Underwater CR Primer then coat the whole hull with Teamac Metaclor Underwater CR Primer. Finally apply 2 coats of Teamac Antifouling A.
Iain on 2017-08-30 15:31:04
Question: Can this be applied directly over a new powder coated finish? I need to paint a brand new, powder coated storage shed.
Thanks
Rust-Oleum 3302 CombiPrimer Adhesion Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Rust-Oleum Mathys 108 Surfa Etch Solution is an easy to use, non-flammable and virtually odour free etching solution for the preparation of smooth concrete surfaces, masonry, galvanized steel and aluminum before applying a paint coating system.
Improves the adhesion of coating systems
Neutralizes alkaline salts
Also ideal to remove "white...
The ultimate direct to metal paint providing years of protection in minutes.
Available in 4,400+ colours, inc. RAL, RAL Design, BS, NCS, NCS 2050 and Metallics
Apply to bare, manually derusted or ready primed mild steel
Primer and metal topcoat in one
Interior/exterior use
Sag resistant - leaves no brush/roller strokes
Please note:...
Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion is a high quality anti-rust primer for Rust-Oleum CombiColor. The Anti-Corrosion Primer will ensure an even longer anti-rust protection on new or rusted steel surfaces and provides and enhances protection against corrosion.
Recoatable after 2 hours
For new / slightly rusted surfaces
Grey for...
Rust-Oleum 3202 Galvinoleum Primer is a single pack super adhesion primer for galvanised steel, plastic or other smooth surfaces. Should be used on galvanised steel, stainless steel, aluminium, copper, glass, porcelain and other smooth, dense surfaces. Only intended for brush application and can be recoated with Rust-Oleum 7500 Alkythane....
General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site.
Provides an economical way of making sure you will have what you need
Ideal for interior and exterior paint projects
Click to jump down to...
Rust-Oleum CombiColor Multi-Surface is a solvent-based, adhesive primer and topcoat in one. Based on an alkyd binder it provides good adhesion to many types of substrates and is lead and chromate free.
For Professional use
For internal/external use
Quick drying
Direct application to many surfaces, including wood, metal*, interior and...
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3).
Please click here for important information about these kits.
Kit Contents:
SET 1 (Hand Tools)
1 x Rust-Oleum...