Teamac Zinc Rich Primer Aerosol

488/Q107/1
TEA787

Teamac Zinc Rich Primer Aerosol, is very high concentration of metallic zinc gives cathodic protection and is a form of cold galvanising.

Colour
Size
Finish
£19.50(ex. VAT)
£23.40 (inc. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

Description

Teamac Zinc Rich Primer Aerosol, contains a very high concentration of metallic zinc and allows conductivity in the dried film. The zinc coating gives cathodic protection and is a form of cold galvanising. Teamac Zinc Rich Primer is suitable for iron and steel to protect against corrosion. The coating must be in direct contact with the iron or steel to work correctly.



Click To Jump To Section:




Features & Benefits




Product Specification


Technical Data
Volume Solids 56.8%
VOC Content 381 g/litre
SG 2.99 @ 20°C
Viscostity 8 Poise @ 25°C
Flash Point Above 32°C (closed cup)



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Maximum 70 μm 125 μm 8 m2/litre @ 70 micron D.F.T.



The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application



Drying Times


Drying Times At 20°C/RH 50%
Touch Dry: 30 Mins
Dry To Handle: 8 Hours
Dry To Recoat: 8 hours or overnight
Fully Cured: N/A



Low temperature and high humidity will adversely affect application, drying and performance of any coating.



Surface Preparation


  • Ensure all surfaces are clean, dry and free from grease, oil and any other contaminates.
  • Bare steel should be free from dust, rust and scale.
  • Blast cleaning to SA 2½ is recommended. If blast cleaning is impractical, mechanical cleaning should be employed as hand cleaning does not clean the steel to the required degree.
  • Any oil or grease should be removed with solvent before de-rusting.
  • Where blast cleaning is carried out after assembly, special attention must be paid to edges, corners, nuts, bolts welds, etc.
  • Welds should, if necessary be ground and all weld spatter, slag etc. must be removed.



Preceeding Coat


  • Apply direct to prepared iron and steel.



Subsequent Coat




Mixing


  • Mix very well before use.



Application Conditions


  • As dictated by normal good painting practice.
  • In confined spaces, provide adequate ventilation during application and drying.
  • Must be applied in direct contact with the iron or steel to be affective.



Health & Safety


See safety data sheet - SDS 10733

Click to go back to the top of the page

Product Details
787-182048

Data sheet

Manufacturer
Teamac
For Use By
Consumer Use
Water / Solvent Based
Solvent
For Use On
Iron, Steel
Application Method
Brush, Airless Spray
Sheen
Matt
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Single, Two or Three Pack
Single
Pack Size
400ml Aerosol
Suitable Substrates
Suitable for iron and steel
Touch Dry (at 20°C)
30 Mins
Dry to Handle (at 20°C)
8 Hours
Dry to Recoat (at 20°C)
8 hours or overnight
Fully Cured (at 20°C)
N/A
Coverage
8 m2/litre @ 70 micron D.F.T.
Recommended Thinner/Cleaner
Teamac Thinner 15 /16
Compatible Primers
Teamac Zinc Phosphate Primer
Solids by Volume
56.8%
VOC
381 g/litre
Size
400ml
Recommended Dry Film Thickness
70 μm
Recommended Wet Film Thickness
125 μm
UN Number
UN1950
Base Type
Solvent-Based
Suitable For Use On
Iron
Finish
Matt
Application Method
Brush
Product Type
Primer
Product Range
Zinc
Colour Family
Grey
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send

IMPORTANT SHIPPING & DELIVERY INFORMATION

Teamac Zinc Rich Primer Aerosol is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like

Teamac Thinner 16

A specially formulated blend of solvents designed to mix with its compatible Teamac or Coo-Var coating to create an optimal consistancy for application. Suitable for application by Brush, Roller or Spray.  Teamac Thinner 16 can also be used for the cleaning of some surfaces prior to application of the coating. Suitable for cleaning of the...

Price £11.68 (ex. VAT)
In Stock and Available for Delivery

Teamac Thinner 15

A specially formulated blend of solvents designed to mix with its compatible Teamac or Coo-Var coating to create an optimal consistancy for application. Suitable for use with Brush, Roller or Spray. Teamac Thinner 15 can also be used for the cleaning of some surfaces prior to application of the coating. Can be use for cleaning of...

Price £27.46 (ex. VAT)
In Stock and Available for Delivery

Teamac Zinc Phosphate Primer

Teamac Zinc Phosphate Primer, an anticorrosive primer on iron and steel, for use with a range of conventional topcoats such as Teamac Marine Gloss and Teamac Metalcote Plant Enamel. Can be used for: Marine purposes Fire escapes Metal gates Metal garage doors Ideal in coastal areas Click to jump down to Technical Data Coverage...

Price £14.83 (ex. VAT)
In Stock and Available for Delivery

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £17.22 (ex. VAT)
In Stock and Available for Delivery