Teamac All Metals Primer
  • Teamac All Metals Primer

Teamac All Metals Primer

516/W201/703/E

Teamac All Metals Primer, is a water thinnable, general purpose metals primer which has very good anti-corrosive properties suitable for priming most metals including iron, steel, aluminium, brass, copper and more.

  • Application: Brush, Roller, Airless Spray
  • Finish: Matt
  • Coverage: 12 Square Metres Per Litre
  • Suitable For: Metals
  • Drying Times: Touch Dry: 1.5 hours Hard Dry: 4 hours
  • Click to jump down to Technical Data

**Available for delivery - see Delivery Options below**

Colour
Size
Finish
£29.41
£35.29 Incl. VAT
Quantity

Description

Teamac All Metals Primer, is a water thinnable acrylic metals primer which has very good anti-corrosive properties.  Teamac Water Based All Metals Primer is a general purpose metals primer, suitable for priming most metals including iron, steel, aluminium, brass, copper and more.



Click To Jump To Section:




Features & Benefits


  • Application: Brush, Roller, Airless Spray
  • Finish: Matt
  • Coverage: 12 Square Metres Per Litre
  • Suitable For: Metals
  • Drying Times: Touch Dry: 1.5 hours Hard Dry: 4 hours
  • Click to jump down to Technical Data



Product Specification


Technical Data
Volume Solids 27%
VOC Content Max 47 g/litre
SG 1.15 @ 20°C
Viscostity 2.7 Poise @ 25°C
Flash Point Non-flammable



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Maximum 20 to 25 μm 85 μm 12 m2/litre @ 25 micron D.F.T.



The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.



Drying Times


Drying Times At 20°C/RH 50%
Touch Dry: 1.5 Hours
Dry To Handle: 4 Hours
Dry To Recoat: 6 Hours
Fully Cured: 3 - 5 Days



Low temperature and high humidity will adversely affect application, drying and performance of any coating.



Surface Preparation


  • Ensure all surfaces are clean, dry and free from grease, oil and any other contaminates.
  • Bare steel should be free from dust, rust and scale.
  • Blast cleaning to SA 2½ is recommended. If blast cleaning is impractical, mechanical cleaning should be employed as hand cleaning does not clean the steel to the required degree.
  • Any oil or grease should be removed with CooVar Degreaser before de-rusting.
  • Where blast cleaning is carried out after assembly, special attention must be paid to edges, corners, nuts, bolts, welds etc.
  • Welds should, if necessary be ground and all weld spatter, slag etc. must be removed.



Preceeding Coat


  • N/A



Subsequent Coat




Mixing


  • Mix well before use.



Application Conditions


  • Do not paint when temperature will be at or below 7°C during the painting and drying process as dictated by normal good painting practice.
  • Care must be taken during application that the temperature is above the dew point to avoid any contamination.
  • In confined spaces, provide adequate ventilation during application and drying.

Application Methods


Method Airless Spray Conventional Spray Brush Roller
  Yes No Yes Yes



  • Thinner (Max vol): Clean Water (5%)
  • Nozzle size: 0.015"
  • Nozzle pressure: 1800 to 2000 psi
  • Cleaning solvent: Clean Water



Health & Safety


See safety data sheet - SDS 11143 in the attachements section above.

Click to go back to the top of the page

Product Details
516/W201/703/E

Data sheet

Manufacturer
Teamac
Water / Solvent Based
Water
For Use On
Iron, Steel, Aluminium, Brass, Copper
Application Method
Brush, Roller, Airless Spray
Sheen
Matt
Colour
Standard / Ready Mixed
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Single
Pack Size
1L, 2.5L
Touch Dry (at 20°C)
1.5 Hours
Dry to Handle (at 20°C)
4 Hours
Dry to Recoat (at 20°C)
6 Hours
Fully Cured (at 20°C)
3 - 5 Days
Coverage
12 m2/litre @ 25 micron D.F.T.
Recommended Thinner/Cleaner
Clean Water
Compatible Topcoats
Teamac Marine Gloss, Teamac Metalcote Plant Enamel
Min. Application Temperature
Do not paint when temperature will be at or below 7 °C
Solids by Volume
27%
VOC
Max 47 g/litre
Size
0.5 litre, 1 litre, 2.5 litre
Recommended Dry Film Thickness
20 to 25 μm
Recommended Wet Film Thickness
85 μm
UN Number
Not regulated
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Teamac Metalcote Plant Enamel

Teamac Metalcote Plant Enamel, is a tough, flexible enamel paint with an attractive gloss finish and excellent durability. It has good resistance to lubricating, mineral oils, many common industrial chemicals and heat. Good resistance to oils, chemicals and heat Ideal for use on all types of machinery including tractors Available in...

Price £13.03
In stock

Teamac Marine Gloss

Teamac Marine Gloss is a high quality, modified long oil alkyd marine coating. It has excellent gloss and opacity. High gloss Excellent opacity and adhesion Touch dry in as little as 4 hours (at 20°C) Full hardness in 5 - 7 days Suitable for all general marine areas, bridge fonts, deck work, masts, superstructures etc Available in...

Price £8.46
In stock

General Painting Application Kit

General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site. Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects Click to jump down to...

Price £8.69
In stock

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.53
In stock