Fast drying tintable primer in 6,700+ colours which may be used in a wet-on-wet system. For use on Steel, Cast Iron, Light Alloys, and can be recoated without sanding even after a long period.
Suitable for use on Machinery, Signage and Metal Fabrication, and Previously Painted Surfaces
Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours
*Note: RAL Pearl colours shown are approximations only - matches will not be exact
Product can be purchased as a Two Component Pack, or as Base or Hardener only
Selemix 7-414 2K Epoxy Vinyl Primer (Fast Curing) is a fast drying tintable primer which may be used in a wet-on-wet system. It can be used over a wide range of substrates and can be recoated without sanding even after a long period.
For use on Steel, Cast Iron, Light Alloys & Previously Painted Surfaces on Machinery, Signage and Metal Fabrication.
Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours.
*Note: RAL Pearl colours shown are approximations only - matches will not be exact.
Apply only on a clean and dry surface with a temperature above the dew point to avoid condensation. In confined spaces, provide adequate ventilation during application and drying.
Steel (Blast Cleaned):
Blast clean to ISO 8527-1 SA 2.5 with a blast profile of maximum 40 µm Rz.
Note: A first coat of 7-413 Epoxy Primer is recommended before spraying a second coat with 7-414
Steel/Cast Iron:
Machine sand with P80-120 discs and degrease
Light Alloys:
Machine sand with P280-320 discs and degrease
Phosphated Steel:
Abrade with SCOTCHBRITE® and degrease
Painted Surfaces:
Machine sand with P240-320 discs and degrease
Do not use over wash primers or 1K synthetic primers.
Mixing
Thoroughly mix paint before activating and check colour before use
Please Note: Refer to the Product Data Sheet for detailed information regarding mixing ratios for the relevant binder/base and hardener/activator used.
Application Notes
Features
Conventional Spray
Spraygun Setup:
Nozzle:
Gravity: 1.6-1.8mm
Suction: 1.8-2.0mm
Pressure feed: 1.2-1.4mm
Air Pressure:
HVLP: 2 Bar
Standard: 2.5-3 Bar
Fluid Pressure:
N/A
Number of coats:
2
Flash-off between coats:
10-15 mins
Drying:
Air dry 2 hours at or bake at 60°C for 30-45 mins
Flash-off before bake:
10-15 mins
Wet Film Thickness:
150-200 microns
Dry Film Thickness:
40-50 microns
Please see the Product Data Sheet for detailed Application Instructions before use.
Theoretical Coverage
4.5-5m²/L at 50 microns DFT
Note: Please see the Product Data Sheet for detailed information.
Drying Times
Drying Times 20°C
Dust Free
15-20 mins
Handleable
2-3 hours
Hard Dry
24 Hours
Stoving
30-45 minutes @60°C (according to film thickness)
Overcoating time
Minimum: 2 hours
Maximum: 2 months without sanding on clean surface with any 2K Selemix Topcoat
Please Note: Lower temperature or film thickness higher than 50µm will extend drying times
Health & Safety
For comprehensive Health, Safety and Environmental advice, please refer to the relevant Material Safety Data Sheets and product can labels
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Selemix 7-414 2K Epoxy Vinyl Primer (Fast Curing) is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
For use with selected products in the Selemix range including Selemix 7-410 2K Epoxy Topcoat. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use OnlyMore Information Delivery Info
For use with selected products in the Selemix range including Selemix 7-410 2K Epoxy Topcoat. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use OnlyMore Information Delivery Info
Tintable primer with 6,700+ colours and a fast drying time for use in a wet on wet system when recoated with 2K Topcoats.For use on Steel, Cast Iron, Aluminium, Light Alloys, GRP & Previously Painted Surfaces Good anticorrosive properties - Suitable for the finishing and protection of machinery, agricultural & construction...
Fast drying tintable primer with 6,700+ colour options, may be used in a wet-on-wet system. For steel, cast iron, light alloys, and can be recoated without sanding even after a long period.Suitable for use on previously painted surfaces, machinery, signage and metal fabrication Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and...