Fast-curing 2K high build epoxy primer containing anticorrosive pigments, for use on steel, zinc plated steel and aluminium providing excellent protection against corrosion.
Please note: Colours shown are for illustrative purposes only
Selemix 4-0440/4-0441 2K Epoxy HB Anticorrosive Primer (Fast Curing) is a 2K high build epoxy primer containing anticorrosive pigments. It is available in grey and white.
It is recommended for use on steel, zinc plated steel and aluminium providing excellent protection against corrosion. It has outstanding chemical resistance, low VOC content and when used with Selemix 2K Topcoats, gives a high performance coating system suitable for aggressive industrial environments.
2K Epoxy HB Anticorrosive Primer provides excellent protection against corrosion (part of ISO 12944-6 certified system), MED certified for the use in ships with no risk of smoke or fire.
This product MUST be purchased/used in conjunction with its manufacturer specified base or activator/hardener. This product can be purchased as a Base or Hardener separately only - please see the drop down menu above.
Please ensure to refer to the Product Data Sheet for mixing ratios or please contact our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for details.
For Industrial Use Only.
Apply only on a clean and dry surface with a temperature above the dew point to avoid condensation. In confined spaces, provide adequate ventilation during application and drying.
Steel (Blast Cleaned):
Steel/Cast Iron:
Phosphated Steel:
Galvanised Steel:
Aluminium:
Painted Surfaces:
Do not use over wash primers or 1K synthetic primers.
| Features | Conventional Spray | Air-Assisted Airless |
|---|---|---|
By Weight: 4-0440/4-0441 Primer 9-020/9-025 Hardener | By Weight: 1000 150 90-120 | By Weight: 1000 150 0-30 |
By Volume: 4-0440/4-0441 Primer 9-020/9-025 Hardener | By Volume: 4 1 0.6-1 (15-25%) | By Volume: 4 1 0-0.2 (0-5%) |
| Viscosity (at 20°C): | 25-35 secs DIN4 | 50-55 secs DIN4 |
| Pot Life (at 20°C): | 3-4 hours | 3-4 hours |
Mixing Ratio:
Please Note: Refer to the Product Data Sheet for detailed information regarding mixing ratios for the relevant base and hardener/activator used.
| Features | Conventional Spray | Airless Spray |
|---|---|---|
| Spraygun Setup: | Nozzle: Gravity: 1.8mm Suction: 1.8-2.0mm Pressure feed: 1.2-1.4mm | Nozzle: 11-13-15 thou 0.28-0.33-0.38 mm |
| Air Pressure: | Standard: 2.5-3 Bar | 2.5-3 Bar |
| Fluid Pressure: | N/A | 70-100 Bar |
| Number of coats: | 2 | 2 |
| Flash-off between coats: | 10-15 min at 20°C | 10-15 min at 20°C |
| Drying: | Bake at 60°C for: 60 mins with 9-020 hardener 45 mins with 9-025 hardener | Bake at 60°C for: 60 mins with 9-020 hardener 45 mins with 9-025 hardener |
| Flash-off before bake: | 10-15 min | 10-15 min |
| Wet Film Thickness: | 225-275 microns (110-135 microns per coat) | 200-250 microns (100-150 microns per coat) |
| Dry Film Thickness: | 100-120 microns | 120-150 microns |
Please see the Product Data Sheet for detailed Application Instructions before use.
Note: Please see the Product Data Sheet for detailed information.
| Drying Times 20°C | |
|---|---|
| Dust Free | 10-15 min |
| Touch Free | 4 hours |
| Hard Dry | 8-10 hours |
| Stoving | 45-60 minutes @60°C (according to film thickness and hardener selection) |
| Overcoating time | Minimum: 1 hour for low to medium film build Safest: 3 hours in case of uncertain film build Maximum: 2 months without sanding on clean surface with any 2K Selemix Topcoat |
| Please Note: Lower temperature or film thickness higher than 150µm will extend drying times | |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Selemix 4-0440/4-0441 2K Epoxy HB Anticorrosive Primer (Fast Curing) is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
For use with selected products in the Selemix range including Selemix 7-410 2K Epoxy Topcoat. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use OnlyMore Information Delivery Info
£52.85 (incl. VAT)
£44.04 (ex. VAT)
For use with selected products in the Selemix range including Selemix 7-410 2K Epoxy Topcoat. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use OnlyMore Information Delivery Info
£49.72 (incl. VAT)
£41.43 (ex. VAT)
