407 Multi Surface Primer
  • 407 Multi Surface Primer

407 Multi Surface Primer

RP407

407 Multi Surface Primer is a primer/sealer which offers excellent stain blocking and alkali resisting properties across substrates such as tiles, wood, metal (including galvanised), plaster, existing paint, masonry and most plastic.

  • Single pack
  • Internal or external use
  • Gives excellent coverage to a multitude of stains
  • Touch dry in just 30 mins @ 20 °C
  • Matt finish
  • Low odour
  • Click to jump down to Technical Data

Colour
Size
£23.39
VAT excluded

£28.07 Tax incl.
Quantity

Description

407 Multi Surface Primer is a primer/sealer which offers excellent stain blocking and alkali resisting properties across substrates such as tiles, wood, metal (including galvanised), plaster, existing paint, masonry and most plastic.

Suitable for interior or exterior use, 407 Multi Surface Primer is made with low odour solvents. It also gives excellent coverage to a multitude of stains, helping to prevent bleeding through the finishing coat.



Quick Links - Click To Jump To Section:




Features & Benefits


  • Excellent stain blocking
  • Alkali resisting properties
  • Single pack
  • Internal or external use
  • Touch dry in 30 minutes @ 20 °C
  • Suitable for use on tiles, wood, metal (including galvanised), plaster, existing paint, masonry and most plastic
  • Matt finish
  • Low odour



Typical Properties


Technical Data
  407 Multi Surface Primer
Specific Gravity: 1.10 @ 20 °C
Volume Solids: 36%
Wet Film Thickness: 100 microns
Dry Film Thickness: 35 - 40 microns
Typical Viscosity: 4.0 Poise C&P @ 25 °C
Flash Point: Above 32°C (closed cup)
V.O.C. 499g/litre



Coverage


  • Expected spreading rate of 10m²/litre at 50 microns dry film thickness
  • The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application



Surface Preparation


  • All surfaces should be clean, dry, sound and free from oil and dirt
  • Wire brush or sand surface to remove any loose / flaking material and rust



Mixing:

  • Mix well before use



Application


  • As dictated by normal good painting practice
  • In confined spaces, provide adequate ventilation during application and drying



Subsequent Coat:

  • Any suitable topcoat



Cleaning


  • LO White Spirit



Curing


Drying Times
  407 Multi Surface Primer
Touch Dry: 30 Mins @ 20 °C
Hard Dry: 4 hours @ 20 °C
Full Hardness: 3-5 Days @ 20 °C
Minimum Overcoating Time: 4-6 hours



Low temperature and high humidity will adversely affect application, drying and performance of any coating.



Storage & Shelf Life


  • Store in closed original container at temperatures between 5°C and 25°C
  • Keep away from heat, sparks and open flame
  • Keep containers upright
  • See section 7.2 of the Safety Data Sheet for further information



Health & Safety


  • Please refer to Material Safety Data Sheet for information
  • 407 Multi Surface Primer shall be applied strictly in accordance with the manufacturer’s instructions

For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]



It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
RP407

Data sheet

Manufacturer
Rawlins Paints
Water / Solvent Based
Solvent
For Use On
Tile, Wood, Metal, Plaster, Masonry Surfaces, Plastic
Application Method
Brush, Roller
Sheen
Matt
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Dry to Recoat (at 20°C)
4-6 hours
Fully Cured (at 20°C)
3-5 Days @ 20 °C
Coverage
10m² per litre
Solids by Volume
36%
VOC
499g/litre
Touch Dry
30 Mins
Recommended Dry Film Thickness
35 - 40 microns
Recommended Wet Film Thickness
100 microns
UN Number
UN1263
Specific Gravity
1.10 @ 20 °C
Viscosity
4.0 Poise C&P @ 25 °C
Hard Dry
4 hours @ 20 °C
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Kate Finlayson  on 2018-09-12 13:40:33
Question: 

Will multi surface primer cover a wooden summer house that has been treated with Danish oil

Answer: 

Danish Oil is usually pure, without silicone, so assuming this is the case here we would recommend Coo-Var Penetrating Wood Primer which should be suitable for this job.

questions Denis Harrison on 2016-09-04 18:13:27
Question: Will this product adhere to gloss paint without sanding down?
Answer: 

Yes, as long as the surface to be painted is clean and dry.


Question about the product

* Required fields
(read)
Send