This is a primer from Jotun that can be applied to steel, aluminium or wood, and features very good adhesion properties on all these substrates. Jotun Pilot QD Primer is an anti-corrosive one component oxidatively drying alkyd coating that is a fast drying, high build, zinc phosphate pigmented product.
Jotun Barrier 80
A primer for carbon steel, repair of inorganic zinc silicate coating and damaged galvanised steel substrates in highly corrosive environments.
Jotun Barrier 80 is a two component polyamide cured zinc rich epoxy coating. Click here for more Jotun products.
Jotun Barrier 80 is a two component polyamide cured zinc rich epoxy coating. It is a high solids, high zinc dust containing product that conforms to the compositional requirements of SSPC paint 20, level 2 and ISO 12944-4. It provides very good corrosion protection as part of a complete coating system. To be used as primer in atmospheric environments. Suitable for carbon steel, repair of inorganic zinc silicate coating and damaged galvanised steel substrates. This product complies with ASTM D520 type I zinc dust.
Jotun Barrier 80 is suitable for structural steel and piping to be exposed to corosive environments up to very high. Recommended for offshore environments, refineries, power plants, bridges, buildings, mining equipment and general structural steel. Specialy designed as a primer in coating systems where extended durabilty is required.
Approvals and certificates
- Tested in acordance with ISO 12944-6, high expected durabilty in corosivity category C5-I
- Highways Agency Approved - Item No. 109
Additional certificates and approvals may be available on request.
Features & Benefits
- Fast dry-to-recoat and fast to-handle
- Designed for protection in severe corrosive environments
- High solids
- Wide user area
- Easy application
Fast dry-to-recoat and fast dry-to-handle
- new construction: min. Sa 2½ (ISO 8501-1:2007)
- maintenance: UHPWJ to WJ2 (NACE No.5/SSPC-SP 12)
“Green step” – Health, Environment and Safety
- High solids and low VOC
- Pure zinc dust (ASTM D520 type II)
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Be the first to ask a question about this product!
Quick Air Dry High Build Primer for blasted and non-blasted steel, a one-pack post-fabrication primer that dries fast for a quick turnaround. Suitable for use in mild to moderate corrosive environments, such as those typically found in commercial buildings, hospitals and schools. Features: Overcoatable with Cromadex 222, 233 & 400...
An inexpensive primer based upon iron oxide for use on structural steelwork, iron and metalwork which can be left as a short term finish or overcoated with Teamac Marine or Industrial coatings.
Jotun Barrier Smart Pack is a two component ceramically reinforced polyamide cured zinc rich epoxy coating. 1:1 mixing ratio for easy use and reduced wastage. Designed for brush and roller application, makes it ideal for maintenance and touch up. Suitable for carbon steel, repair of inorganic zinc silicate coating and damaged galvanised steel...
Jotun Penguard HSP MIO is a two component polyamide cured epoxy coating that is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high build product. Can be used as a primer or a mid coat in atmospheric environments. Specially designed for new construction where fast dry to handle and over coating times are required.
A high-build epoxy mastic coating used for atmospheric exposed and submerged steel. Top Features Excellent film build and edge protection Surface tolerant characteristics Cures at low temperature
Sherwin-Williams FIRETEX C69 is a two pack epoxy, fast-track blast primer for intumescent coatings. It is a fast-track temporary protective coating for surfaces prepared by abrasive blast cleaning, designed for use under FIRETEX intumescent coatings.
Nullifire PM021 General Purpose Epoxy Primer is a two-components epoxy polyamide primer with excellent resistance to salts, water and alkalies, and with very good resistance to mild acids and solvents.
PPG Sigma Etch, a phosphoric acid-based etch solution for treating new, unweathered galvanized surfaces, where blasting or abrasion is not possible, prior to painting. Changes color on application from blue to black to indicate the effectiveness of primary pre-treatment Meets the requirements of British Rail's 'T-wash' solution May be...
International Intergard 214 is a two component epoxy sealer coat pigmented with aluminium flake for the effective penetration and sealing of thermally sprayed aluminium coatings to eliminate porosity. Has specification approval for UK Department of Transport Item No.159.
Cromadex 903 Two Pack Chromate-Free Etch Primer is a two pack chromate-free etch primer designed for use over a wide range of substrates. It is formulated without the use of zinc tetroxy-chromate helping to reduce health and safety concerns. Cromadex 903 should be used to improve adhesion and corrosion resistance of all systems used over metal...
International Interplus 770 is a low VOC, two component, high solids, internally flexibilised, surface tolerant epoxy primer/intermediate coating intended for use as a versatile, high performance maintenance coating to upgrade tightly adhering existing coatings to longer life durable systems.
International Interprime 198 is a one component, fast drying, high performance, universal alkyd primer. Primarily intended for use as a maintenance primer on hand prepared steel but equally suitable for use at new construction in the fabrication shop.
Jotun Penguard WF is a two component, anticorrosive water borne epoxy coating that is a versatile, fast drying product containing flash rust inhibitors. It is specially designed for new construction where fast dry to handle and over coating times are required. Jotun Penguard WF can be used as primer, mid coat, finish coat or as single coat...
An all-purpose immersion-grade epoxy that has a variety of attributes including low-temperature cure, surface tolerance and fast recoat times. Can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. Top Features Excellent corrosion protection Excellent application characteristics Fast...
Coo-Var Red Oxide Metal Primer is a good general purpose metal primer for ferrous metallic objects (iron and steel). To be used for short periods of exposure during transportation/storage or to be overcoated with a suitable Coo-Var / Teamac topcoat to provide a durable lasting finish for metal.