Rust-Oleum 3202 Galvinoleum Primer is a single pack super adhesion primer for galvanised steel, plastic or other smooth surfaces. Should be used on galvanised steel, stainless steel, aluminium, copper, glass, porcelain and other smooth, dense surfaces. Only intended for brush application and can be recoated with Rust-Oleum 7500 Alkythane.
Jotun Penguard HSP MIO
Jotun Penguard HSP MIO is a two component polyamide cured epoxy coating that is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high build product. Can be used as a primer or a mid coat in atmospheric environments. Specially designed for new construction where fast dry to handle and over coating times are required.
Jotun Penguard HSP MIO is a two component polyamide cured epoxy coating that is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high build product. Can be used as a primer or a mid coat in atmospheric environments. Specially designed for new construction where fast dry to handle and over coating times are required. Suitable for properly prepared aluminium, carbon steel, galvanised steel, shop primed steel and stainless steel substrates.
Jotun Penguard HSP MIO is suitable for structural steel and piping to be exposed to corrosive environments. Recommended for power plants, airports, buildings, refineries and mining equipment.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Typical Coverage (per coat)
- 5.8m² per litre
- Touch Dry
- 1 hour
- Brush, Spray
Be the first to ask a question about this product!
A versatile epoxy primer with excellent resistance to salts, water and alkalies, with very good resistance to mild acids and solvents. Top Features Excellent corrosion resistance Cured film is tough and abrasion resistant Excellent adhesion to aluminium
Sherwin-Williams M600 (formerly known as Leighs M600) is a quick drying single pack alkyd anticorrosive primer pigmented with zinc phosphate, used for the protection of steel where speed of drying is important.
International Interzinc 52 (Winter Grade) is supplied with a winter grade curing agent to enable more rapid cure at lower temperatures. A two component, metallic zinc rich epoxy primer which complies with the composition and performance requirements of SSPC Paint 20.
Jotun Penguard Low Temp Additive is recommended when a faster curing or painting at lower substrate temperatures is desired with Penguard HB, Penguard Primer and Penguard Special.
SikaCor EG 1 is a two-pack, high-solids, epoxy-based intermediate coat containing micaceous iron oxide. The coating is designed as a mechanically resistant intermediate coat on steel surfaces exposed to atmospheric conditions, hot-dip galvanized steel, zinc-spray, stainless steel and aluminium.
A specially-formulated primer for application on to metals to enhance adhesion properties, and allow the primer to physically bond onto the metal using an incorporated activating acid that "etches" into the substrate. Advantages For Aluminium, Copper and Galvanised Steel surfaces. White in colour. Upto 12-months shelf life.
A metal primer with surface tolerant properties, can also be used as an intermediate coat, or self-priming finish over steel and zinc primers. Top Features Ready to apply after mixing Economical fit for use epoxy Used as a primer, intermediate, or finish coat VOC compliant to current AIM regulations
Sherwin-Williams Transgard TG110 is a zinc phosphate pigmented 2-pack epoxy temporary protective primer, used as a temporary protective for steel surfaces prepared by abrasive blast cleaning.
Sherwin-Williams Macropoxy C425V2 (formerly Epigrip C425V2) is a high build 2-pack epoxy zinc phosphate primer/buildcoat to provide anti-corrosive protection of carbon steel surfaces prepared by abrasive blast cleaning. Network Rail and NORSOK approved, ideal for use in internal/external exposed conditions including offshore, petrochemical and sub-sea...
International Interprime 306 is a single component, fast drying, high build alkyd primer used as a shop applied post-fabrication primer specifically designed for a blast, fabricate and prime steel production route, and where fast drying and rapid handling properties are required.
International Interplus 256 is a low VOC, two component internally flexibilised high build surface tolerant epoxy primer. It is pigmented with aluminium and lamellar micaceous iron oxide for improved corrosion resistance and represents the second generation in surface tolerant technology.
A high build coating for the protection of structural steelwork against corrosion that can be used as either an intermediate, or finish coat in interior and exterior environments.
Rust-Oleum 769/780 Damp-Proof Rust Primer is a single pack rust primer for direct application on slightly moist or dry metal surfaces. Rust-Oleum 769/780 Damp-Proof Rust Primer is specially developed to be applied on hand tool prepared sound rusted steel surfaces.
A fast-drying steel primer that provides corrosion protection on structural steel. Well suited for fabrication shops that need fast cure to dry and handle times. Top Features Rapid cure and fast-drying VOC compliant for most areas Good for filling properties on rough and pitted steel
Jotun Penguard Express B11 can be used as a primer, mid coat, finish coat or as a single coat system in atmospheric environments. Suitable for properly prepared carbon steel, aluminium, concrete and galvanised steel substrates. It can be applied at sub zero surface temperatures.