International Interprime 198 is a one component, fast drying, high performance, universal alkyd primer. Primarily intended for use as a maintenance primer on hand prepared steel but equally suitable for use at new construction in the fabrication shop.
Jotun Penguard Express MIO
Jotun Penguard Express MIO is a two component amine cured epoxy coating that is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high build product. Specially designed for new construction where fast dry to handle and over coating times are required. Can be used as a primer, mid coat, finish coat or as a single coat system in atmospheric environments.
Jotun Penguard Express MIO is a two component amine cured epoxy coating that is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high build product. Specially designed for new construction where fast dry to handle and over coating times are required. Can be used as a primer, mid coat, finish coat or as a single coat system in atmospheric environments. Suitable for properly prepared carbon steel, stainless steel, aluminium and concrete substrates. It can be applied at sub zero surface temperatures.
Jotun Penguard Express MIO is suitable for structural steel and piping to be exposed to corrosive environments up to very high. Recommended for offshore environments, refineries, power plants, bridges, buildings and mining equipment.
Approvals & Certificates
- Part of a complete system that is certified to Network Rail Line Specification NR/L3/CIV/039 System M20, N4 and N9 (Cert. No. XM92/M20-140, M20-179, XM92-162, XM92-163, XM92/M20-166, XN90/N4-077, N4-102, XN90-084, XN90-085, XN90/N4-090, XN90/N9-065, XN90/N9-066) Item 7.2.2.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Typical Coverage (per coat)
- 5.9m² per litre
- Touch Dry
- 1 hour
- Brush, Spray
Be the first to ask a question about this product!
International Interplate 398 is a two component, fast drying modified epoxy phosphate prefabrication primer for manual or automatic spray application. International Interplate 398 is intended to pre-prime steel prior to the fabrication process and can can be overcoated with a large range of coating systems.
Jotun Barrier is a two component polyamide cured zinc rich epoxy coating. From Jotun, this is a very high zinc dust containing product and it conforms to the compositional requirements of SSPC paint 20, level 2. Jotun Barrier provides very good corrosion protection as part of a complete coating system. To be used as primer in atmospheric environments.
International Interplus 356 is a low VOC, two component, internally flexibilised, high build, low temperature curing (down to -5°C, 23°F), surface tolerant epoxy primer, metallic pigmented with aluminium and lamellar micaceous iron oxide for increased corrosion resistance.
Rust-Oleum 569/580 Quick Drying Metal Primer is a single pack quick drying metal primer for bare and lightly rusted metal. It should be used on new, blasted or slightly rusted steel surfaces. Depending on the exposure conditions, it can be recoated with a variety of Rust-Oleum Systems assuring the appropriate protection.
Cromadex 902 One Pack Etch Primer is a one pack etch primer that can be both air dried and stoved making it suitable for use in most paint shops. The product has enhanced adhesion properties to mild steel ensuring the success of the coating system. Cromadex 902 is available in white, grey and black.
International Intergard 405 is a two component epoxy sealer coat, pigmented with micaceous iron oxide. Formulated on proprietary polymer technology, which provides rapid cure and overcoating, even at low temperatures.
This primer from Jotun is excellent in atmospheric environments, it provides corrosion protection as part of a complete coating system to carbon steel substrates. Jotun Barrier ZEP is a two component polyamide cured zinc epoxy coating.
A fast-drying steel primer that provides corrosion protection on structural steel. Well suited for fabrication shops that need fast cure to dry and handle times. Top Features Rapid cure and fast-drying VOC compliant for most areas Good for filling properties on rough and pitted steel
A high solids, epoxy intermediate/finish coat, providing exceptionally high film builds (up to 200 microns DFT per coat), enabling maximum performance in a minimum number of coats. Can be used year round due to its ability to cure down to temperatures as low as 2°C.
From Jotun, this primer is for structural steel and piping in highly corrosive environments, ideal for offshore environments, refineries, power plants, bridges, buildings, mining equipment and general structural steel. Jotun Barrier 77 is a two component polyamide cured zinc rich epoxy coating.
Sherwin-Williams M600 (formerly known as Leighs M600) is a quick drying single pack alkyd anticorrosive primer pigmented with zinc phosphate, used for the protection of steel where speed of drying is important.
A fast drying metal primer based on two-component epoxy resin offering extra protection against corrosion on bare or blasted metal, also ideal for galvanised metal under severe conditions.