• Sherwin-Williams Acrolon 1850

Sherwin-Williams Acrolon 1850

1850
SHE1907

Sherwin-Williams Acrolon 1850 is a two pack Isocyanate free finish based on an acrylic epoxy binder system. It is a finish coat for exterior exposed surfaces where retention of gloss is required, and the use of isocyanate products is precluded or undesirable. 

  • Available in 400+ colours, including RAL and BS

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
Size
Finish
£144.29(ex. VAT)
£173.14 (inc. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

Description

Sherwin-Williams Acrolon 1850 is a two pack Isocyanate free finish based on an acrylic epoxy binder system. It is a finish coat for exterior exposed surfaces where retention of gloss is required, and the use of isocyanate products is precluded or undesirable. 

Sherwin-Williams Acrolon 1850 is the next generation in non-isocyanate topcoats; utilising new technology, Acrolon 1850 has been principally designed for the offshore and fabric maintenance markets, where the use of isocyanates is restricted, but good coverage is desired with little downtime.

Endorsements

  • Complies with Norsok M501 Rev 6 System 1 as part of a three coat system.
  • Certifired for decontamination in accordance with EX07190/06/33/03. 

Recommended Primers

  • Compatible with a wide range of Macropoxy, Dura-plate, Zinc Clad Epoxy Primers and Buildcoats.
  • ACROLON 1850 must be applied over epoxy materials within 4 days at 23°C to ensure satisfactory intercoat adhesion.
  • For use with alternative undercoats please contact Sherwin- Williams 

Recommended Topcoats

Sherwin-Williams Acrolon 1850 is indefinitely self-overcoatable.

Application Equipment

Airless Spray

Nozzle Size: 0.33mm (13 thou)
Fan Angle: 40°
Operating Pressure: 176kg/cm² (2500 psi)

The airless spray details given above are intended as a guide only. Details such as fluid hose length and diameter, paint temperature and job shape and size all have an effect on the spray tip and operating pressure chosen. However, the operating pressure should be the lowest possible consistent with satisfactory atomisation. As conditions will vary from job to job, it is the applicators’ responsibility to ensure that the equipment in use has been set up to give the best results. If in doubt Sherwin-Williams should be consulted.

Conventional Spray

Nozzle Size: 1.27mm (50 thou)
Atomising Pressure: 3.5kg/cm² (50 psi)
Fluid Pressure:  0.7kg/cm² (10 psi)

The details of atomising pressure, fluid pressure and nozzle size are given as a guide. It may be found that slight variations of pressure will provide optimum atomisation in some circumstances according to the set up in use. Atomising air pressure depends on the air cap in use and the fluid pressure depends on the length of line and direction of feed i.e. horizontal or vertical.

Brush

The material is suitable for brush application. 

Application Conditions & Overcoating

This material should preferably be applied at temperatures in excess of 10°C In conditions of high relative humidity, ie 80-85% good ventilation conditions are essential. Substrate temperature shall be at least 3°C above the dew point and always above 0°C.

At application temperatures below 10°C, drying and curing times will be significantly extended, and spraying characteristics may be impaired.
Application at ambient air temperatures below 5°C is not recom- mended.

Steelwork coated with ACROLON 1850 Special Finish should be protected from weather for 6 hours after application. 

Product Details
1850

Data sheet

Application Method
Brush, Spray
Sheen
Gloss
Colour
Fully Tintable
Single, Two or Three Pack
Two-Pack
Pack Size
5L, 20L
Application
Brush, Spray
Coverage
2.94m² per litre
Touch Dry
1 Hour
UN Number
UN1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £17.22 (ex. VAT)
In Stock and Available for Delivery