Jotun Pilot II is a one component oxidatively drying alkyd coating from Jotun that has a gloss finish with good gloss retention. To be used as a topcoat in atmospheric environments. Jotun Pilot II is recommended as a topcoat, and for touch-up purposes for marine engines, topside, deck and superstructure areas and for a wide range of...
Rust-O-Thane 9200 Handy Pack
Rust-Oleum's hard wearing, washable polyurethane coating (9200) is now also available in convenient 1 litre packaging. Ideal for smaller projects the new convenient 2-component packaging provides the base and activator in one convenient kit and the activator is supplied with a user-friendly spout cap.
Rust-O-Thane 9200 Handy Pack is a waterbased, satin, 2K polyurethane for a very durable and colourfast finish on metal, concrete, wood and more. It is also ideal as a topcoat for epoxy and acrylic systems.
Rust-O-Thane 9200 Handy Pack is intended for application on substrates, which are coated with Rust-Oleum epoxy or acrylic coatings (e.g. 9100, 5401, Pegasol or Pegalink). The application area consists of coated floors, coated walls and primed wood/metal. Rust-O-Thane 9200 Handy Pack assures appropriate protection against solvents, moderate alkalines, weak acids and chemical cleaning. Especially recommended where general urethane performance like excellent weather resistance (UV), easy cleaning and abrasion resistance is required.
Features & Benefits
- Washable, scratch-resistant and UV-resistant satin finish coating
- Wide colour range including a transparent finish available
- Automotive level UV stability; does not yellow
- Water-based formula with low odour
- High abrasion resistance, extremely scratch-resistant
- Smooth satin finish with excellent flow
- For many different surfaces
- Can be used on floors, walls, stairs, wood and metal
|Solids content in volume:||37%|
|Heat Resistance:||90C (dry heat), above 65C discolouration may occur|
|Mixing Ratio:||Base : Activator = 5.66 : 1 by volume|
DRYING TIMES AT 20°C/RH 50%
|Touch dry:||2 Hours|
|Dry to handle:||4 Hours|
|Dry to recoat:||24 Hours|
|Fully cured:||2 Days|
|Pot life:||2 Hours|
|Induction time:||5 mins|
6.2 m²/l at 60 μm dry (depending on colour) for floors.
9.2 m²/l at 40 μm dry (depending on colour) for other applications.
Remove grease, oil and all other surface contamination using alkaline or high pressure (steam) cleaning in combination with appropriate detergents. Sand previous coatings that are in good condition to remove gloss and to roughen the surface slightly. Assure that the previous coating is compatible with the Rust-O-Thane 9200 Handy Pack by making a test application. Remove bad adhering coatings by scraping, wire brushing or sanding. (Spot)prime with commended Rust-Oleum or Mathys coatings. The surface must be clean and dry during application.
DIRECTIONS FOR USE
Add activator gradually to base material and mix with a mechanical mixing device. Do not dilute during the pot-life. Do not use after 2 hours. Do not store residue of mixed product in a closed can.
Temperature of air, substrate and coating material between 5°C and 35°C and relative humidity below 80 %. The substrate temperature must be at least 3°C above dew point.
APPLICATION & THINNING: BRUSH
Use undiluted. Use natural bristles, longhair brushes.
APPLICATION & THINNING: ROLLER
Use undiluted. Use medium nap (polyamide, 8-12 mm). Apply slowly in even strokes.
APPLICATION & THINNING: AIRLESS SPRAY
Use undiluted. Pneumatic and electric airless equipment. Tip size: 0.013-0.015 inch.
Fluid pressure: 200 bar.
CLEANING OF EQUIPMENT / SPILLS
Water and soap, before drying
- Max dry film thickness for floors: 75 μm dry, equals 200 μm wet. For walls: 60 μm dry, equals 160 μm wet.
- For use on floors submitted to heavy abrasion, standard and medium colours are recommended. In case of deep and/or bright tones (red, yellow, orange, green, blue etc), it is advised to apply a clear topcoat.
- The product is not recommended in case of stagnating water and/or immersion.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Brush, Roller, Spray
- 6.2 - 9.2m² per litre
- Touch Dry
- 2 Hours
Be the first to ask a question about this product!
Sika Permacor 2707 is a 2-pack epoxy resin topcoat with high mechanical resistance and with excellent chemical resistance to aqueous and alkaline exposure. Sika Permacor 2707 is used as a top coat for metal surfaces exposed to extreme interior environments, e.g. for highly exposed structures, pipe work, cladding panels, railings, machines and other...
PPG Sigma Vikote 56 is a modified acrylic finish coat for above-water areas. Featuring good gloss and colour retention, resistance to water and splash of mild chemicals. This fast-drying coat can be applied at temperatures down to –10°C (14°F). Top Features Dries in as little as 30 minutes (@ 20°C) Apply by spray, brush or roller Gloss...
Tor Quick Drying Machinery Enamel finishes factory machinery, tools, agricultural implements, etc, applying by airless spray. Available in over 400 colours from RAL and BS. Quick drying Touch dry in 30 minutes Hard dry after 2 hours An alkyd resin binder pigmented with inorganic pigments and thinned with xylene Use with a suitable...
Cromadex 635 Two Pack Polyurethane Leatherette Topcoat is a two pack polyurethane leatherette topcoat with excellent exterior durability and chemical resistance. The product exhibits excellent colour retention adding value to the finished article, whilst the leatherette effect can help differentiate your finish. Available in the full Cromadex range of...
Sherwin-Williams L654 (formerly known as Metagrip L654) is a quick drying micaceous iron oxide paint, which provides a tough hard wearing abrasion resistant functional coating for the protection of external steel work such as storage tanks, pylons, bridges etc., with good durability under industrial and coastal exposure conditions. Suitable for...
International Intergard 1735 is a high performance, low VOC, water borne two component epoxy with a high gloss finish. International Intergard 1735 is a tough, hard wearing chemically resistant epoxy finish suitable for most circumstances where the odour or emissions from solvent based coatings are unacceptable.