Sherwin-Williams Macropoxy M330 (formerly known as Epigrip M330) is a 2-pack epoxy sealercoat for use over zinc silicate and other types of zinc rich primers. It is also used as a blast primer for use over stainless steel.
Please note: This product is made to order subject to a minimum order quantity of 150L and an extended lead time of 14 working days
Sherwin-Williams Macropoxy M330 (formerly known as M330) is a 2-pack epoxy sealercoat for use over zinc silicate and other types of zinc rich primers. It is also used as a blast primer for use over stainless steel.
Recommended Primers & Topcoats
Zinc Clad J984 Zinc Rich Primer
Dox-Anode D5V2
Indefinitely overcoatable with epoxy systems provided the surfaces to be coated have been suitably cleaned. Where a high degree of gloss and colour retention is required, overcoat with Acrolon C137V2, Acrolon C237 within 7 days at a minimum dft of 50 microns or in the case of Accrolon C750V2 overcoat within 4 days. These overcoating times refer to achievement of optimum adhesion at 23°C and will vary with temperature.
For overcoating with alkyd systems consult Technical Team for advice.
Application Conditions & Overcoating
Epoxy paints should preferably be applied at temperatures in excess of 10oC. In conditions of high relative humidity, ie 80-85% good ventilation conditions are essential. Substrate temperature shall be at least 3oC above the dew point and always above 0°C.
At application temperatures below 10°C, drying and curing times will be significantly extended, and spraying characteristics may be impaired.
Application at ambient air temperatures below 5°C is not recommended.
In order to achieve optimum water and chemical resistance, temperature needs to be maintained above 10oC during curing.
If it is desired to overcoat outside the times stated on the data sheet, please seek advice from Technical Team.
Additional Notes
Drying times, curing times and pot life should be considered as a guide only.
The curing reaction of epoxies commences immediately the two components are mixed, and since the reaction is dependent on temperature, the curing time and pot life will be approximately halved by a 10°C increase in temperature and doubled by a 10°C decrease in temperature.
When M330 is used as a tie-coat or sealer coat over inorganic zinc silicate, the zinc silicate must be left for a minimum of 16 hours at 15°C and then checked for cure. Prior to overcoating, the inorganic zinc silicate primer must be fully cured.
Care must be taken to ensure that Macropoxy M330 is not over-applied on to the zinc silicate otherwise there is a possibility of pinholing occurring.
Epoxy Coatings - Tropical Use
Epoxy paints at the time of mixing should not exceed a temperature of 35°C. At this temperature the pot life will be approximately halved. Use of these products outside of the pot life may result in inferior adhesion properties even if the materials appear fit for application. Thinning the mixed product will not alleviate this problem.
The maximum air and substrate temperature for application is 50°C providing conditions allow satisfactory application and film formation. If the air and substrate temperatures exceed 50°C and epoxy coatings are applied under these conditions, paint film defects such as dry spray, bubbling and pinholing etc. can occur within the coating.
Numerical values quoted for physical data may vary slightly from batch to batch.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3).
Please click here for important information about these kits.
Kit Contents:
SET 1 (Hand Tools)
1 x Rust-Oleum...
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
Colourmatch Service Disclaimer
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage