Bradite Chlorinated Rubber

CG23 / CC24

Bradite Chlorinated Rubber is a high performance single pack chlorinated rubber finish with excellent chemical & water resistance. Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004.

  • Available in over 350+ colours in RAL and BS
    • Please Note : At present selected colours are temporarily unavailable, the colour picker below shows all currently available colours
  • Choose from gloss and eggshell finishes
  • Resistant to fungal growth
  • Highly resistant to oils and chemicals
  • Ideal for water immersion, such as swimming pools

Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
Size
Finish
£77.98
VAT excluded

£93.57 Tax incl.
Quantity

Description

Bradite Chlorinated Rubber is a high build gloss/eggshell, chlorinated rubber based finish. For use on concrete, porous mineral and suitably prepared ferrous and non-ferrous surfaces requiring a quick drying coating with excellent water and good chemical resistance.

Resists the growth of fungus! Ideal for those damp environments and exterior use. Suitable for water immersion, for example, swimming pools, etc. Not suitable for drinking water or fish ponds.

Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems.


Features & Benefits

  • Available in over 350+ colours in RAL and BS
  • Choose from gloss and eggshell finishes
  • Resistant to fungal growth
  • Highly resistant to oils and chemicals
  • Gives good weathering properties when used as the finish coat in a protective paint system
  • Ideal for water immersion, such as swimming pools
  • Can be used at low temperatures, even down to 0°C


Preparation

For ferrous, non-ferrous, concrete and other absorbent mineral substrates which are dry, free of contamination, dust, efflorescence laitance and have been properly prepared. Compatibility with existing coatings should be confirmed by preparing and painting a test patch. Unsuitable for epoxy tar & bitumen paints, Portland cement, marble & tiled surfaces.

When painting new concrete it is vital to ensure the substrate is fully cured and free of laitance. Power floated, shiny or unpainted non porous concrete should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite TA37.

High pressure water cleaning to remove all loose and flaking paint and contamination back to a sound substrate. For best performance, complete vacuum blast cleaning of the substrate is recommended. Bradite TD39 industrial strength detergent washing and rinsing should be used with scrubbing to remove grease or oil.

Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting.

Galvanised steel, aluminium and other non-ferrous metal substrates should be roughened by mechanical abrading or sweep blasting with inert grit. Steel should be blast cleaned to SIS-Sa 2½ minimum, blast profile 35-50 microns and surface free of soluble salts, or de-rusted manually or mechanically to SIS-St 3 minimum.

Painting System – Concrete Swimming Pools

For application on concrete or other absorbent substrates, the first coat should be thinned 15-20% with Bradite Thinner TC32 to allow penetration into the substrate.

1st coat: Chlorinated Rubber Gloss CG23 (thinned) if required.

2nd coat: Chlorinated Rubber Gloss CG23.

For maintenance painting the 1st coat will be a touch up to bare areas. Please note that drying/curing times will vary depending on film thickness, temperature and relative humidity.

For well-constructed pools, particularly those with an external waterproof membrane, best results are obtained with Bradite Chlorinated Rubber Gloss CG23. Where the site has a high water table and the pool is constructed without waterproof barrier, the higher porosity Bradite Chlorinated Rubber Eggshell CC24 is preferred since this material will minimise blistering due to external water pressure when the pool is empty. 

Painted pool should be left to thoroughly dry before filling. In temperate climates, assuming good ventilation and air movement, this will take approximately 10 days from final coat application.

Painting System – Industrial New Build & Maintenance

1st coat: Bradite Chlorinated Rubber Primer CP26.

2nd coat: Bradite Chlorinated Rubber Eggshell CC24.

3rd coat: Bradite Chlorinated Rubber Gloss CG23.

For galvanised steel and other non-ferrous surfaces, the first coat should be substituted with Bradite Barrier Primer EU96. For maintenance, the first coat will be spot priming exposed substrate only. 

In all cases, always refer to the Health and Safety sheet for the product before use, and observe the warning phrases on the label.


Application

Application and use should always conform to the codes of practice described in BS 6150 and BS 5493.

Brush and Roller: Thin with 0 - 5% Bradite Thinner TC32 as required. Short pile “Mohair” sleeve preferred for best appearance.

Conventional Air Spraying: Thin with 5 - 15% Bradite Thinner TC32 as required, tip size – 2.0 mm, tip pressure 60psi (0.4MPa) approximately.

Airless Spraying: Thin with 0 - 10% Bradite Thinner TC32 as required, tip size - 13 thou (0.33mm) approximately, tip pressure - 2100 psi (15MPa) approximately.

Clean all equipment immediately after use with Bradite Thinner TC32 for best results.

Product Details
CG23 / CC24

Data sheet

For Use On
Steel, Concrete
For Use On
Concrete, Steel
Application Method
Brush, Roller, Spray
Application Method
Brush, Roller, Spray
Sheen
Gloss, Eggshell
Sheen
Gloss, Eggshell
Colour
Fully Tintable
Colour
Fully Tintable
Single, Two or Three Pack
Single
Single, Two or Three Pack
Single
Pack Size
5L
Pack Size
5L
Application
Brush, Roller, Spray
Coverage
12m2 per Litre
Touch Dry
30 Mins
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send