Quick drying, low odour, water thinned primer/finish coat in 2,500+ colours with excellent adhesion, stain blocking and anti-corrosive properties. Dries in 30 minutes and recoatable within an hour.
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Suitable for use on:
Stain Locking
Encapsulates stains in the primer coat, application of second coat will be required to hide and in extreme cases a third. One Can should be allowed to hard dry prior to overcoating this will take at least one hour, over application may result in longer drying times.
Aluminum, stainless steel, galvanised steel, copper and other metals
Cleaned and degreased with methylated spirit, and lightly abraded if possible. White salts on weathered galvanising must be removed during cleaning and degreasing. Light surface rusting can be treated with Bradite Rust Convertor RC46. Heavy rusting to be removed to clean metallic finish (SIS-St 3).
New Wood
Ensure moisture content of the timber is below 15% before commencing application. Damp wood should never be painted as this may give rise to blistering, flaking, cracking and premature coating failure. Knots to be wiped using methylated spirit, for heavy or active knots spot prime with Aluminum Wood Primer.
Hard Woods
Wipe with methylated spirit to remove excess resin, changing the face of the cloth regularly. Lightly abrade.
Green Oak
Should not be painted unless it has been weathered for at least 6 months.
Exterior cladding, Powder coated, Varnish and Existing paint finish
Remove all loose and flaking paintwork. Degrease using Bradite TD39 Industrial Degreaser, followed by clean water rinse. Rub down thoroughly with a medium grade sand paper to provide a key and a defect free smooth surface, “feathering in” areas where paint has been removed.
UPVC, Formica, Melamine and Plastics
For long term performance, degrease using methylated spirit & lightly abrade surfaces
New Plaster Walls
For plaster skim, allow at least four weeks for the plaster to thoroughly dry. Apply a primer coat by thinning the paint with a 5 to 25% (v/v) addition of clean water, depending upon the porosity of the substrate. Cut in by brushing at the same dilution recommendation as for priming, to promote flow and sealing of the substrate. For new, fully plastered walls, allow at least six months for the plaster to thoroughly dry before painting.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
 Craig Fleming on 2024-01-16 16:04:10 | Question: Hi, could this be used on windows to stop light coming in? |
Answer from Rawlins’ Technical Team: Assuming the glass is thoroughly cleaned and degreased to ensure the removal of all surface contaminants, grease and oils, this product can be applied direct to glass, however when painting glass brush strokes can be visible from the other side of the glass. It is recommended to apply 3 full coats to achieve the intended outcome, as it is a 3-in-1 product it will prime, seal and stain block the glass for the intended finish. This is a non-removable product once the glass has been coated, assuming you would like the option of a removable product, you could consider Coo-Var White Glass Shading. | |
| Amanda Bruce on 2023-01-24 15:06:07 | Question: How long is the guarantee on a front door before it would need re-painting? Also why would it keep flaking in some parts despite sanding and re-coating, particularly around beading? |
Answer from Rawlins’ Technical Team: If flaking is occuring there could be a few possible causes, please can you provide more information and pictures of the areas to [email protected]. | |
| graham on 2021-09-17 15:32:25 | Question: can you use this product Bradite One eggshell for painting modern kitchen cupboards, that are made of mdf with a coating on top |
Answer from Rawlins’ Technical Team: Assuming you check for compatibility and adhesion prior to full application, the substrate is clean, dry, sound and prepared as detailed in the technical data sheet then yes. If you are looking for a scuff resistant and scrubbable option assuming you check for compatibility and adhesion prior to full application we can recommend Zinsser Bulls Eye 1-2-3 followed by Zinsser Perma-White Interior. | |
| Jo on 2021-08-31 07:15:25 | Question: The decorator is wanting to put a primer on my old wood internal staircase so he can see where it needs filling and any imperfections, is it ok to use your ok to use your Bradite One Can on top of normal primer, also which would you suggest best for internal old wood staircase, (you have so many) ie quick drying. Thank you |
Answer from Rawlins’ Technical Team: Bradite One Can is suitable for both application to bare or previously painted timber and would be classed as a primer/finish. We would not recommend this product be used on any areas that would be walked on. | |
| [email protected] on 2021-07-19 14:05:01 | Question: How do I clean the PVC door before applying the paint |
Answer from Rawlins’ Technical Team: Assuming the door is UPVC we would recommend using Bradite Industrial Degreaser. | |
| Sarah on 2021-05-30 10:39:56 | Question: Hello, I see that this can be used for a vinyl wardrobe, can it also be used on vinyl flooring? I have a very small area at the bottom of my stairs that I’d like to paint. Many thanks, |
Answer from Rawlins’ Technical Team: We would recommend you test for compatibility and adhesion prior to application as it does not list vinyl as a substrate. This is not suitable for use on a floor, assuming the vinyl floor is clean, dry, sound, prepared as detailed in the technical data sheet, you also test for compatibility and adhesion prior to application we can recommend Smartkote Protectakote UVR Smooth. This is available in black, white or clear. | |
| Raz on 2020-06-03 11:10:00 | Question: Hi, can this be used on exterior aluminium. If yes, what prep does it need before. Many thanks |
Answer from Rawlins’ Technical Team: Assuming the aluminium is clean, dry, degreased and abraded prior to application Bradite One can can be used on External Aluminium. | |
| Mike Sometville on 2019-02-25 11:29:45 | Question: I have fitted wardrobe which has a vinyl surface finish. Does the vinyl need any prep to ensure adhesion. Thanks |
Answer from Rawlins’ Technical Team: Bradite One Can would be suitable for painting over vinyl coated wardrobes, clean and degrease using Bradite Industrial Degreaser diluted with 9 parts warm water and scrubbing, rinse with clean water and allow to dry. Apply three coats allowing not less than 1 hour between coats, in the colour of choice. | |
| Alistair Spiers on 2019-02-04 14:38:12 | Question: Is it possible to get your one can paint in clear? We have some very old interior wood cladding that the client wants to have a colour wash finish,so we don't want to obliterate the grain with a primer,but do want to block the knots and seal rusty nails.thanks Alistair |
Answer from Rawlins’ Technical Team: Bradite One Can is not available in clear. Zinsser SealCoat would be a good product to try. It will seal the knots and rust stains. It may pay to put a couple of coats on where there are rust stains. You can then apply a colour wash coat over the SealCoat. You may need to do some tests with the colour wash over the Sealcoat. | |
Bradite One Can Eggshell is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Bradite Industrial Degreaser is an aqueous alkaline low foaming detergent used for degreasing contaminated surfaces prior to painting.Ideally suited for degreasing oily or soiled surfaces and for removing road dirt Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systemsMore...
£67.54 (incl. VAT)
£56.28 (ex. VAT)
Bradite Fastrac Rust Converter is a high performance, single-pack, water-based rust converter intended for the treatment and passivation of surface rust on all hand or mechanically prepared rusty ferrous surfaces.Especially suited for objects which may be difficult to sand blast such as; fences, iron railings, guttering and outdoor...
£45.08 (incl. VAT)
£37.57 (ex. VAT)
A quick-drying matt finish primer/finish coat in one can with a choice of 2,500 colours, for use as a low odour, quick drying scuff and moisture resistant, adhesion promoting, stain locking, anticorrosive coating.For interior or exterior walls and trim, masonry (Brickwork/Concrete etc) ferrous metals, non-ferrous metals, common plastics...
£32.95 (incl. VAT)
£27.46 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)
