Carboline Carbocrylic 1295 HS is a high solids topcoat for steel and concrete surfaces, to provide good weathering capabilities. Offers a glossy, smooth, hard finish that is easy cleanable. Recommended for chemical industry, offshore, power and heavy industry.
Two-component High Solids Acrylic Epoxy Finish
Offers excellent corrosion and weathering protection.
NORSOK Approved for offshore
Available in 350+ colours, including RAL and BS
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cart
Carboline Carbocrylic 1295 HS is a high solids topcoat for steel and concrete surfaces, to provide good weathering capabilities. Offers a glossy, smooth, hard finish that is easy cleanable. Recommended for chemical industry, offshore, power and heavy industry.
Offers excellent corrosion and weathering protection.
NORSOK Approved for offshore
Available in 350+ RAL colour shades
Product Specification
Technical Data
Carboline Carbocrylic 1295 HS
Volume Solids:
62 ± 2%
Dry Temperature Resistance:
Continuous: 120°C (248°F)
Non-Continuous: 150°C (302°F)
Theoretrical Coverage Rate:
8,3 m²/l at 75 µm.
Allow for loss in mixing and application
Dry Film Thickness:
50 - 150 microns (1.95 - 5.9 mils) per coat
Topcoats:
Normally not topcoated
Limitations:
Not recommended for immersion service
Density:
1.29 g/cm³ depending on color
Shelf Life:
24 months at 24°C
Storage:
Store indoors
Storage Temperature & Humidity:
5° - 45°C, 0-95% RH
Flash Point (Setaflash):
1295 HS Part A 27°C
1295 HS Part B 16°C
Packaging:
Part A 16.1 litres
Part B 2.3 litres
Drying Times
Curing Schedule
Surface Temperature
Dry To Touch
Dry To Handle
Dry To Recoat
Final Cure
4°C (39°F)
12 Hours
20 Hours
48 Hours
9 Days
16°C (61°F)
5 Hours
8 Hours
20 Hours
5 Days
24°C (75°F)
3 Hours
5 Hours
12 Hours
3 Days
29°C (84°F)
2 Hours
3 Hours
8 Hours
2 Days
These times are based on 75 µm dry film thickness. Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure.
Surface Preparation
General
Surfaces must be clean and dry. Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating.
Steel
Apply over clean, dry primers, or intermediate coats as recommended.
Concrete
Apply over clean, dry primers, or intermediate coats as recommended.
Application Methods
Product Information
Mixing:
Power mix separately, then combine and power mix
Thinning:
May be thinned up to 10% with Thinner no.41
Use of thinners other than those supplied or recommended by Carboline may adversely affect product warranty whether expressed or implied. Contact Rawlins on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected] for further information.
Ratio:
7:1 Ratio (A to B) by volume
Conventional Spray:
Pressure pot equipped with dual regulators, 3/8” I.D. minimum material hose, 0.052” fluid tip and appropriate air cap.
Pot Life:
3 Hours @ 24°C and less at higher temperatures
Airless Spray:
Pump Ratio: 30:1
GPM Output 3.0 (minimum)
Material Hose: 3/8" I.D. (minimum)
Tip Size: 0.013” - 0.017”
Output PSI: 2000-2300
Filter Size: 60 mesh
Brush & Roller (General):
Brush and roller recommended for small areas only.
Application Conditions
Product Application Conditions
Condition
Material
Surface
Ambient
Humidity
Minimum
10°C (50°F)
4°C (39°F)
4°C (39°F)
0%
Maximum
35°C (95°F)
55°C (131°F)
50°C (122°F)
90%
Industry standards are for substrate temperatures to be 3°C above the dew point. This product simply requires the substrate temperature to be above the dew point.
Health & Safety
Refer to the safety data sheet in the attachments section above and tin label prior to use.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Carboline Carbocrylic 1295 HS is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...