Carboline Carbocrylic 3359 TC

8383

Carboline Carbocrylic 3359 TC is a topcoat for steel or concrete in a two or three coat system, providing excellent film properties, high gloss and good weatherability. Provides very good corrosion protection with a suitable primer system.

  • Single component
  • Fast drying
  • Low VOC
  • Gloss finish

**Available for delivery - see Delivery Options below**

Colour
Size
Finish
£75.38
VAT excluded

£90.45 Tax incl.
Quantity

Description

Carboline Carbocrylic 3359 TC is a topcoat for steel or concrete in a two or three coat system, providing excellent film properties, high gloss and good weatherability. Provides very good corrosion protection with a suitable primer system. Recommended topcoat in a three coat system using Carbozinc 858 and Carbocrylic 3358 IMC. Refer to the preparation & application section below..



Click To Jump To Section:




Features & Benefits


  • Single component
  • Fast drying
  • Low VOC
  • Gloss finish



Product Specification


Technical Data
Carboline Carbocrylic 3359 TC
Volume Solids: 38 ± 2%
Primer: Recommended topcoat in a three coat system using Carbozinc 858 and Carbocrylic 3358 IMC.
Dry Temperature Resistance: Continuous: 100°C (212°F)
Non-Continuous: 120°C (248°F)
Theoretrical Coverage Rate: 5,1 m²/l at 75 µm
Allow for loss in mixing and application
Dry Film Thickness: 50 – 100 µm per coat, normally 75 µm
Wet Film Thickness: 130-160 µm per coat, normally 200 µm
Limitations: Not recommended for immersion service
Topcoats: Normally not topcoated
Shelf Life: 24 months at 24°C
Storage: Store indoors. Keep from freezing.
Storage Temperature & Humidity: 5° - 45°C, 0 - 95% relative humidity



Drying Times


Curing Schedule
Surface Temperature Tack Free Surface Dry To Topcoat
10°C (50°F) 1 Hour 3 Hours
25°C (77°F) 30 Minutes 1.5 Hours
35°C (95°F) 20 Minutes 1 Hour



  • Drying times will depend upon film thickness, air humidity, ventilation and other local site conditions. Above times should be considered as guidelines provided good ventilation conditions.



Surface Preparation


General

  • Surface must be clean and dry.
  • Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating.

Steel

Concrete

  • Apply over clean and dry surface.
  • Concrete must be cured min. 28 days at 24°C and RH 50% or equivalent.
  • A test patch is recommended to check adhesion.



Application Methods


Product Information
Mixing: Power mix until uniform in consistency
Avoid excessive air entrapment
Thinning: May be thinned up to 5% with clean potable water
General: Pre-rinse equipment with butyl glycol followed by clean potable water before spraying
Airless Spray: Pump Ratio: 30:1 (minimum)
GPM Output: 3.0 (minimum) 12 liters/min
Material Hose: 3/8” I.D. (minimum)
Tip Size: .013”-.019”
Output PSI: 1800-2200
Filter Size: 60 mesh
Brush & Roller: Use a synthetic bristle brush or short nap synthetic roller cover with phenolic core.



Application Conditions


Product Application Conditions
Condition Material Surface Ambient Humidity
Minimum 10°C (50°F) 10°C (50°F) 10°C (50°F) 0%
Maximum 40°C (104°F) 50°C (122°F) 40°C (104°F) 75%



  • Do not apply when the surface temperature is less than 3°C above the dew point.
  • Do not apply if temperatures are expected to drop below 10°C within 24 hours of application.
  • Film thickness above recommendations may reduce product properties.



Health & Safety


Clean Up

  • Use clean potable water followed by butyl glycol or other suitable solvent to dry equipment. In case of spillage, absorb and dispose of in accordance with local applicable regulations.

Safety

  • Read and follow all caution statements on this product data sheet and on the MSDS for this product.
  • Employ normal workmanlike safety precautions.
  • Hypersensitive persons should wear protective clothing, gloves and use protective cream on face, hands and all exposed areas.
  • Use adequate ventilation.
  • Keep container closed when not in use.
  • Refer to the safety data sheet in the attachments section above and tin label prior to use.
Product Details
8383

Data sheet

Manufacturer
Carboline
For Use By
General Use
For Use On
Steel, Concrete
Application Method
Brush, Roller, Spray
Sheen
Gloss
Colour
Standard / Ready Mixed
VOC Levels
Low (50-149 g/l)
Single, Two or Three Pack
Single
Pack Size
5L
UN Number
N/A
Colour(s)
White
Base Type
Water-Based
Exterior / Interior Use
Exterior Use
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Carboline Carbocrylic 3358 IMC

Carboline Carbocrylic 3358 IMC is an intermediate coat on steel or concrete in a three coat system, and can be topcoated with several generic types of topcoats. Excellent abrasion resistance and flexibility with good chemical resistance. Single component Fast drying Low VOC Eggshell finish Coverage Calculator More Information...

Price £70.28
In stock

Carboline Carbozinc 858

Carboline Carbozinc 858 is a two-component, high-solids, zinc-filled epoxy primer for corrosion protection of structural steel in highly corrosive environments including offshore, marine, and industrial. Protects steel galvanically Outstanding application properties Cures at low temperatures down to 2ºC Tough and abrasion resistant...

Price £135.75
In stock

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.53
In stock