PPG Thinner 90-53
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
£42.59 (incl. VAT)
£35.49 (ex. VAT)
We no longer stock this product, but can recommend PPG AquaCover One 645 as a great alternative.
Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.
PPG AquaCover 45 (also known as Sigma Aquacover 45) is a one-component, waterborne acrylic dispersion finish for interior accommodation, machinery spaces and superstructures.
PPG AquaCover 45 (also known as Sigma Aquacover 45) is a one-component, waterborne acrylic dispersion finish for interior accommodation, machinery spaces and superstructures. Particularly suitable when solvents are not permitted because of health and safety reasons.
Basic data at 20°C (68°F)
Data for Mixed Product | |
---|---|
Number of Components | One |
Mass density | 1.2 kg/l (10.0 lb/US gal) |
Volume solids | 34 ± 2% |
VOC (Supplied) | Directive 1999/13/EC, SED: max. 9.0 g/kg max. 10.0 g/l (approx. 0.1 lb/US gal) |
max. 6.0 g/l (approx. 0.1 lb/US gal) | |
Recommended dry film thickness | 50 µm (2.0 mils) per coat |
Theoretical spreading rate | 6.8 m²/l for 50 µm (273 ft²/US gal for 2.0 mils) |
Overcoating Interval | Minimum: 1 hour. Maximum: unlimited |
Dry to touch | 1 hour |
Notes:
- See ADDITIONAL DATA: Overcoating intervals
- See ADDITIONAL DATA: Curing time
Substrate temperature and application conditions
Instructions for Use
Stir well before use. The temperature of the paint should preferably be above 15°C (59°F), otherwise extra thinner may be required to obtain application viscosity. Too much tap water results in reduced sag resistance. Adequate ventilation must be maintained during application and curing (please refer to information sheets 1433 and 1434). Must be protected from freezing at all times during storage and/or transport.
Airspray
Recommended thinner: Tap water.
Volume of thinner: 5-10%, depending on required thickness and application conditions.
Nozzle orifice: 1.8 – 2.0 mm (approx. 0.070 – 0.079 in).
Nozzle pressure: 0.3 - 0.4 MPa (approx. 3 - 4 bar; 44 - 58 p.s.i.).<br
Airless Spray
Recommended thinner: Tap water.
Volume of thinner: 0-5%, depending on required thickness and application conditions.
Nozzle orifice: Approx. 0.46 – 0.53 mm (0.018 – 0.021 in).
Nozzle pressure: 12.0 - 15.0 MPa (approx. 120 - 150 bar; 1741 - 2176 p.s.i.).
Brush/Roller
Type: Long haired brush or polyether roller with rounded edges.
Recommended thinner: Tap water.
Volume of thinner: 0–5%
Cleaning Procedure
Tap water and Thinner 70-05. Pulsator filter and tip filter must be taken out of the equipment and cleaned properly.
Cleaning procedure from solvent-borne to waterborne paints:
1st cleaning: THINNER 90-53
2nd cleaning: THINNER 70-05
3rd cleaning: With warm tap water of 30°C (86°F) to 35°C (95°F) after which waterborne paints can be sprayed.
Cleaning procedure from waterborne to solvent-borne paints:
1st cleaning: Warm tap water of 30°C (86°F) to 35°C (95°F)
2nd cleaning: THINNER 70-05
3rd cleaning: THINNER 90-53
Note: THINNER 70-05 can be re-used.
Minimum overcoating interval for DFT up to 50 µm (2.0 mils) when overcoating with itself:
Bear in mind these are minimum intervals; it should be noted that maximum coating intervals are unlimited.
Safety Precautions
For paint and recommended thinners see information sheets 1430, 1431 and relevant Material Safety Data Sheets. Although this is a solvent-free paint, care should be taken to avoid inhalation of spray mist, as well as contact between the wet paint and exposed skin or eyes.
Worldwide Availability
It is always the aim of the manufacturer to supply the same product on a worldwide basis. However, slight modification of the product is sometimes necessary to comply with local or national rules/circumstances. Under these circumstances an alternative product data sheet is used.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
PPG AquaCover 45 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
£42.59 (incl. VAT)
£35.49 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)