PPG Thinner 21-06
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.More Information Delivery Info
£42.59 (incl. VAT)
£35.49 (ex. VAT)
In Stock and Available for Delivery
- There are no more items in your cart
- Shipping Calculated at checkout
- Sub-Total(ex. VAT)(inc. VAT)£0.00£0.00
PPG Sigma Vikote 18 is a high-build, aluminum pigmented chlorinated rubber primer/sealer. Offering excellent water resistance, resistance to well-designed/controlled cathodic protection and can be applied at temperatures down to –10°C (14°F).
- Anti-corrosive primer/sealer
- Unsaponifiable
- Fast-drying
- Tolerates a DFT up to 150 µm (6.0 mils) at overlaps without sagging
- Compatible with antifoulings
Description
PPG Sigma Vikote 18 is a high-build, aluminum pigmented chlorinated rubber primer/sealer. Offering excellent water resistance, resistance to well-designed/controlled cathodic protection and can be applied at temperatures down to –10°C (14°F).
Top Features & Benefits
- Anti-corrosive primer/sealer
- Unsaponifiable
- Fast-drying
- Tolerates a DFT up to 150 µm (6.0 mils) at overlaps without sagging
- Compatible with antifoulings
Product Data
RECOMMENDED SUBSTRATE CONDITIONS AND TEMPERATURES
Substrate Conditions
- Steel with approved zinc silicate shop primer; sweep blasted to SPSS-Ss, welds, rusty and damaged areas blast cleaned to ISO-Sa2½
- Steel; blast cleaned to ISO-Sa2½, blasting profile 40 – 70 µm (1.6 – 2.8 mils)
- Primed steel or previous coat must be dry and free from any contamination
- Galvanized steel must be dry, free from any contamination and zinc salts
- Substrate temperature during application should be at least 3°C (5°F) above dew point
INSTRUCTIONS FOR USE
Stir well before use. The temperature of the paint should preferably be above 15°C (59°F), otherwise extra thinner may be required to obtain application viscosity. Adding too much thinner results in reduced sag resistance
Air Spray
Recommended thinner: PPG Thinner 21-06
Volume of thinner: 6 - 10%, depending on required thickness and application conditions
Nozzle orifice: 1.8 - 2.0 mm (approx. 0.070 – 0.079 in)
Nozzle pressure: 0.3 - 0.4 MPa (approx. 3 - 4 bar; 44 - 58 p.s.i.)
Airless Spray
Recommended Thinner: PPG Thinner 21-06
Volume of Thinner: 0 - 3%, depending on required thickness and application conditions
Nozzle Orifice: Approx. 0.46 mm (0.018 in)
Nozzle Pressure: 15.0 MPa (approx. 150 bar; 2176 p.s.i.)
Brush/Roller
The recommended DFT cannot be reached in one coat
Recommended thinner: PPG Thinner 21-06
Volume of thinner: 0 - 3%
Cleaning Solvent
PPG Thinner 21-06
| Data for Product at 20°C (68°F) | |||||
|---|---|---|---|---|---|
| Number of components | One | ||||
| Mass density | 1.2 kg/l (10.0 lb/US gal) | ||||
| Volume solids | 42 ± 2% | ||||
| VOC (Supplied) | Directive 1999/13/EC, SED: max. 409.0 g/kg. max. 502.0 g/l (approx. 4.2 lb/US gal) | ||||
| Recommended dry film thickness | 75 µm (3.0 mils) per coat | ||||
| Theoretical spreading rate | 5.6 m²/l for 75 µm (225 ft²/US gal for 3.0 mils) | ||||
| Dry to touch | 1 hour | ||||
| Overcoating interval | Minimum: 6 hours. Maximum: Unlimited | ||||
| Shelf life | At least 24 months when stored cool and dry. | ||||
| Overcoating interval for DFT up to 75 µm (3.0 mils) | ||||||
|---|---|---|---|---|---|---|
| Overcoating with... | Interval | -10°C (14°F) | 5°C (41°F) | 10°C (50°F) | 20°C (68°F) | 30°C (86°F) |
| Itself | Minimum Maximum | 24 hours Unlimited | 10 hours Unlimited | 8 hour Unlimited | 6 minutes Unlimited | 4 minutes Unlimited |
| Antifoulings | Minimum Maximum | 36 days Unlimited | 18 hours Unlimited | 12 hours Unlimited | 6 hours Unlimited | 4 hours Unlimited |
| Curing time for solvent-free application | ||
|---|---|---|
| Substrate Temp. | Dry to touch | |
| 5°C (41°F) | 4 hours | |
| 10°C (50°F) | 4 hour | |
| 20°C (68°F) | 1 hour | |
Notes:
- Surface should be dry and free from any contamination
- The above data are a fair indication for normal application conditions
- Longer drying times may be necessary at higher DFT and under unfavourable atmospheric conditions
- For paint and recommended thinners see INFORMATION SHEETS 1430, 1431 and relevant Material Safety Data Sheets
- This is a solvent-borne paint and care should be taken to avoid inhalation of spray mist or vapor, as well as contact between the wet paint and exposed skin or eyes
Product Details
3988-526993
Data sheet
- Manufacturer
- PPG
- For Use By
- Professional Use
- For Use On
- Steel
- Application Method
- Brush, Roller, Spray
- Sheen
- Flat
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Single
- Pack Size
- 20L
- Parts
- One
- Base Type
- Aluminium pigmented chlorinated rubber
- Solvent
- -
- Mixing Ratio
- -
- Key Features
- Anti-corrosive, excellent water resistance, aluminium pigmented
- Touch Dry (at 20°C)
- 1 hour
- Dry to Handle (at 20°C)
- -
- Dry to Recoat (at 20°C)
- 6 hours
- Fully Cured (at 20°C)
- -
- Pot Life (at 20°C)
- -
- Coverage
- 5.6 m²/l for 75 µm (225 ft²/US gal for 3.0 mils)
- Recommended Thinner/Cleaner
- PPG Thinner 21-06
- Unit Contents
- -
- Compatible Primers
- -
- Compatible Topcoats
- Itself
- Max. Application Temperature
- -
- Min. Application Temperature
- -
- Density
- 1.2 kg/l (10.0 lb/US gal)
- Solids by Volume
- 42 ± 2%
- Heat Resistance (up-to)
- -
- VOC
- Directive 1999/13/EC, SED: max. 409.0 g/kg max. 502.0 g/l (approx. 4.2 lb/US gal)
- Shelf Life (Once Opened)
- At least 24 months when stored cool and dry
- UN Number
- UN1263
- Base Type
- Aluminium Pigmented Chlorinated Rubber
- Suitable For Use On
- Steel
- Finish
- Flat
- Application Method
- Spray
- Application Method
- Roller
- Application Method
- Brush
- Product Usage Type
- Primer
- Product Range
- Sigma Vikote
- Colour Family
- Grey
- Categorised As
- Marine Paints > Antifouling Primers & Tie Coats
- Seasonal
- Cold Weather
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
PPG Sigma Vikote 18 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
You might also like
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)
In Stock and Available for Delivery