OPEN AS USUAL DURING LOCKDOWN #3
PPG Sigma Vikote 56 is a modified acrylic finish coat for above-water areas. Featuring good gloss and colour retention, resistance to water and splash of mild chemicals. This fast-drying coat can be applied at temperatures down to –10°C (14°F).
**Available for delivery - see Delivery Options below**
PPG Sigma Vikote 56 is a modified acrylic finish coat for above-water areas. Featuring good gloss and colour retention, resistance to water and splash of mild chemicals. This fast-drying coat can be applied at temperatures down to –10°C (14°F).
Recommended Substrate Conditions and Temperatures
Substrate Conditions
Previous coat (chlorinated rubber, vinyl or acrylic coatings) must be dry and free from any contamination. Substrate temperature during application should be at least 3°C (5°F) above dew point
Instructions for Use
Air Spray
Recommended thinner: PPG Thinner 21-06
Volume of thinner: 5 - 10%, depending on required thickness and application conditions
Nozzle orifice: 1.8 - 2.0 mm (approx. 0.070 – 0.079 in)
Nozzle pressure: 0.2 - 0.3 MPa (approx. 2 - 3 bar; 29 - 44 p.s.i.)
Airless Spray
Recommended thinner: PPG Thinner 21-06
Volume of thinner: 0 - 5%, depending on required thickness and application conditions.
Nozzle orifice: Approx. 0.28 - 0.33 mm (0.011 – 0.013 in)
Nozzle pressure: 12.0 - 15.0 MPa (approx. 120 - 150 bar; 1741 - 2176 p.s.i.)
Brush/Roller
Recommended thinner: PPG Thinner 21-06
Volume of thinner: 0 – 3%
Cleaning Solvent
PPG Thinner 21-06
Safety Precautions
For paint and recommended thinners see information sheets 1430, 1431 and relevant Material Safety Data Sheets. This is a solvent-borne paint and care should be taken to avoid inhalation of spray mist or vapor, as well as contact between the wet paint and exposed skin or eyes.
| Data for Product at 20°C (68°F) | |||||
|---|---|---|---|---|---|
| Number of components | One | ||||
| Mass density | 1.1 kg/l (9.2 lb/US gal) | ||||
| Volume solids | 35 ± 2% | ||||
| VOC (Supplied) | Directive 1999/13/EC, SED: max. 538.0 g/kg max. 569.0 g/l (approx. 4.7 lb/US gal) | ||||
| Recommended dry film thickness | 1.1 kg/l (9.2 lb/US gal) | ||||
| Theoretical spreading rate | 10.0 m²/l for 35 µm (401 ft²/US gal for 1.4 mils) | ||||
| Dry to touch | 30 minutes | ||||
| Overcoating interval | Minimum: 4 hours. Maximum: Unlimited | ||||
| Shelf life | At least 24 months when stored cool and dry | ||||
| Overcoating interval for DFT up to 75 µm (3 mils) | |||
|---|---|---|---|
| Overcoating with... | Interval | 5°C (51°F) | 20°C (68°F) |
| Itself | Minimum Maximum |
8 hours Unlimited |
4 hours Unlimited |
| Curing time for up to 35 µm (1.4 mils) | |
|---|---|
| Substrate Temp. | Dry to touch |
| 5°C (41°F) | 1 hours |
| 20°C (68°F) | 30 minutes |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products. **Available for delivery - see Delivery Options below**
