PPG SigmaCover 400

331922

SigmaCover 400/Amerlock 400, a two-component, high solids, high performance self priming universal epoxy coating for steel and concrete, galvanising, stainless steel and non-ferrous metals, with low VOC. The coating has good adhesion on existing coats, compatible with prepared, damp surfaces, and has many qualifications including Nuclear Service Level 2 (ANSI N 5.12, ANSI N 101.2), ANSI/NSF Standard 61 (potable water) for valves, and MPI Category #108. See further below for more qualifications.

  • Surface tolerant and abrasion resistant, compatible with prepared, damp surfaces
  • Good adhesion on most existing coatings; available in MIO or conventional pigmented grade
  • Good resistance to splash and spillage of chemicals
  • No induction time, with 2 hours pot life; touch dry in 6 hours, fully cured after 7 days
  • Temperature resistant up to 120°C (250°F)
  • See below for more information

Colour
  • Current colour: BS00A05
Choose a colour
Close colour picker
  • White
  • Black
  • RAL1000 - Green Beige
  • RAL1001 - Beige
  • RAL1002 - Sand Yellow
  • RAL1003 - Signal Yellow
  • RAL1004 - Golden Yellow
  • RAL1005 - Honey Yellow
  • RAL1006 - Maize Yellow
  • RAL1007 - Daffodil Yellow
  • RAL1011 - Brown Beige
  • RAL1012 - Lemon Yellow
  • RAL1013 - Oyster White
  • RAL1014 - Ivory
  • RAL1015 - Light Ivory
  • RAL1016 - Sulfur Yellow
  • RAL1017 - Saffron Yellow
  • RAL1018 - Zinc Yellow
  • RAL1019 - Grey Beige
  • RAL1020 - Olive Yellow
  • RAL1021 - Rape Yellow
  • RAL1023 - Traffic Yellow
  • RAL1024 - Ochre Yellow
  • RAL1027 - Curry
  • RAL1028 - Melon Yellow
  • RAL1032 - Broom Yellow
  • RAL1033 - Dahlia Yellow
  • RAL1034 - Pastel Yellow
  • RAL2000 - Yellow Orange
  • RAL2001 - Red Orange
  • RAL2002 - Vermilion
  • RAL2003 - Pastel Orange
  • RAL2004 - Pure Orange
  • RAL2008 - Bright Red Orange
  • RAL2009 - Traffic Orange
  • RAL2010 - Signal Orange
  • RAL2011 - Deep Orange
  • RAL2012 - Salmon Orange
  • RAL3000 - Flame Red
  • RAL3001 - Signal Red
  • RAL3002 - Carmine Red
  • RAL3003 - Ruby Red
  • RAL3004 - Purple Red
  • RAL3005 - Wine Red
  • RAL3007 - Black Red
  • RAL3009 - Oxide Red
  • RAL3011 - Brown Red
  • RAL3012 - Beige Red
  • RAL3013 - Tomato Red
  • RAL3014 - Antique Red
  • RAL3015 - Light Pink
  • RAL3016 - Coral Red
  • RAL3017 - Rose
  • RAL3018 - Strawberry Red
  • RAL3020 - Traffic Red
  • RAL3022 - Salmon Pink
  • RAL3027 - Raspberry Red
  • RAL3031 - Orient Red
  • RAL4001 - Red Lilac
  • RAL4002 - Red Violet
  • RAL4003 - Heather Violet
  • RAL4004 - Claret Violet
  • RAL4005 - Blue Lilac
  • RAL4006 - Traffic Purple
  • RAL4007 - Purple Violet
  • RAL4008 - Signal Violet
  • RAL4009 - Pastel Violet
  • RAL4010 - Telemagenta
  • RAL5000 - Violet Blue
  • RAL5001 - Green Blue
  • RAL5002 - Ultramarine Blue
  • RAL5003 - Sapphire Blue
  • RAL5004 - Black Blue
  • RAL5005 - Signal Blue
  • RAL5007 - Brilliant Blue
  • RAL5008 - Grey Blue
  • RAL5009 - Azure Blue
  • RAL5010 - Gentian Blue
  • RAL5011 - Steel Blue
  • RAL5012 - Light Blue
  • RAL5013 - Colbalt Blue
  • RAL5014 - Pigeon Blue
  • RAL5015 - Sky Blue
  • RAL5017 - Traffic Blue
  • RAL5018 - Turquoise Blue
  • RAL5019 - Capri Blue
  • RAL5020 - Ocean Blue
  • RAL5021 - Water Blue
  • RAL5022 - Night Blue
  • RAL5023 - Distant Blue
  • RAL5024 - Pastel Blue
  • RAL6000 - Patina Green
  • RAL6001 - Emerald Green
  • RAL6002 - Leaf Green
  • RAL6003 - Olive Green
  • RAL6004 - Blue Green
  • RAL6005 - Moss Green
  • RAL6006 - Grey Olive
  • RAL6007 - Bottle Green
  • RAL6008 - Brown Green
  • RAL6009 - Fir Green
  • RAL6010 - Grass Green
  • RAL6011 - Reseda Green
  • RAL6012 - Black Green
  • RAL6013 - Reed Green
  • RAL6014 - Yellow Olive
  • RAL6015 - Black Olive
  • RAL6016 - Turquoise Green
  • RAL6017 - May Green
  • RAL6018 - Yellow Green
  • RAL6019 - Pastel Green
  • RAL6020 - Chrome Green
  • RAL6021 - Pale Green
  • RAL6022 - Olive Drab
  • RAL6024 - Traffic Green
  • RAL6025 - Fern Green
  • RAL6026 - Opal Green
  • RAL6027 - Light Green
  • RAL6028 - Pine Green
  • RAL6029 - Mint Green
  • RAL6032 - Signal Green
  • RAL6033 - Mint Turquoise
  • RAL6034 - Pastel Turquoise
  • RAL7000 - Squirrel Grey
  • RAL7001 - Silver Grey
  • RAL7002 - Olive Grey
  • RAL7003 - Moss Grey
  • RAL7004 - Signal Grey
  • RAL7005 - Mouse Grey
  • RAL7006 - Beige Grey
  • RAL7008 - Khaki Grey
  • RAL7009 - Green Grey
  • RAL7010 - Tarpaulin Grey
  • RAL7011 - Iron Grey
  • RAL7012 - Basalt Grey
  • RAL7013 - Brown Grey
  • RAL7015 - Slate Grey
  • RAL7016 - Anthracite Grey
  • RAL7021 - Black Grey
  • RAL7022 - Umbra Grey
  • RAL7023 - Concrete Grey
  • RAL7024 - Graphite Grey
  • RAL7026 - Granite Grey
  • RAL7030 - Stone Grey
  • RAL7031 - Blue Grey
  • RAL7032 - Pebble Grey
  • RAL7033 - Cement Grey
  • RAL7034 - Yellow Grey
  • RAL7035 - Light Grey
  • RAL7036 - Platinum Grey
  • RAL7037 - Dusty Grey
  • RAL7038 - Agate Grey
  • RAL7039 - Quartz Grey
  • RAL7040 - Window Grey
  • RAL7042 - Traffic Grey A
  • RAL7043 - Traffic Grey B
  • RAL7044 - Silk Grey
  • RAL7045 - Telegrey 1
  • RAL7046 - Telegrey 2
  • RAL7047 - Telegrey 4
  • RAL8000 - Green Brown
  • RAL8001 - Ochre Brown
  • RAL8002 - Signal Brown
  • RAL8003 - Clear Brown
  • RAL8004 - Copper Brown
  • RAL8007 - Fawn Brown
  • RAL8008 - Olive Brown
  • RAL8011 - Nut Brown
  • RAL8012 - Red Brown
  • RAL8014 - Sepia Brown
  • RAL8015 - Chestnut Brown
  • RAL8016 - Mahogany Brown
  • RAL8017 - Chocolate Brown
  • RAL8019 - Grey Brown
  • RAL8022 - Black Brown
  • RAL8023 - Orange Brown
  • RAL8024 - Beige Brown
  • RAL8025 - Pale Brown
  • RAL8028 - Terra Brown
  • RAL9001 - Cream
  • RAL9005 - Black
  • RAL9010 - White
  • RAL9002 - Grey White
  • RAL9003 - Signal White
  • RAL9004 - Signal Black
  • RAL9011 - Graphite Black
  • RAL9016 - Traffic White
  • RAL9017 - Traffic Black
  • RAL9018 - Papyrus White
  • BS00A01
  • BS00A05
  • BS00A09
  • BS00A13
  • BS02C33
  • BS02C37
  • BS02C40
  • BS04B15
  • BS04B17
  • BS04B21
  • BS04C33
  • BS04C37
  • BS04C39
  • BS04D44
  • BS04D45
  • BS04E49
  • BS04E51
  • BS04E53
  • BS06C33
  • BS06C37
  • BS06C39
  • BS06D43
  • BS06D45
  • BS06E50
  • BS06E51
  • BS06E56
  • BS08B15
  • BS08B17
  • BS08B21
  • BS08B25
  • BS08B29
  • BS08C31
  • BS08C35
  • BS08C37
  • BS08C39
  • BS08E51
  • BS10A03
  • BS10A07
  • BS10A11
  • BS10B15
  • BS10B17
  • BS10B21
  • BS10B25
  • BS10B29
  • BS10C31
  • BS10C33
  • BS10C35
  • BS10C39
  • BS10D43
  • BS10D45
  • BS10E49
  • BS10E50
  • BS10E53
  • BS12B15
  • BS12B17
  • BS12B21
  • BS12B25
  • BS12C33
  • BS12C39
  • BS12D43
  • BS12D45
  • BS12E51
  • BS12E53
  • BS14C31
  • BS14C35
  • BS14C39
  • BS14C40
  • BS14E51
  • BS14E53
  • BS16C33
  • BS16C37
  • BS16D45
  • BS16E53
  • BS18B17
  • BS18B21
  • BS18B25
  • BS18B29
  • BS18C31
  • BS18C35
  • BS18C39
  • BS18D43
  • BS18E49
  • BS18E50
  • BS18E51
  • BS18E53
  • BS20C33
  • BS20C37
  • BS20C40
  • BS20D45
  • BS20E51
  • BS22B15
  • BS22B17
  • BS22C37
  • BS22D45
  • BS24C33
  • BS24C39
  • BS101 - Sky Blue
  • BS103 - Peacock Blue
  • BS104 - Azure Blue
  • BS105 - Oxford Blue
  • BS106 - Royal Blue
  • BS107 - Strong Blue
  • BS108 - Aircraft Blue
  • BS109 - Middle Blue
  • BS110 - Roundel Blue
  • BS112 - Arctic Blue
  • BS113 - Deep Saxe Blue
  • BS166 - French Blue
  • BS172 - Pale Roundel Blue
  • BS175 - Light French Blue
  • BS210 - Sky
  • BS216 - Eau De Nil
  • BS217 - Sea Green
  • BS218 - Grass Green
  • BS220 - Olive Green
  • BS221 - Brilliant Green
  • BS223 - Middle Bronze Green
  • BS224 - Deep Bronze Green
  • BS225 - Light Brunswick Green
  • BS226 - Middle Brunswick Green
  • BS227 - Deep Brunswick Green
  • BS228 - Emerald Green
  • BS241 - Dark Green
  • BS262 - Bold Green
  • BS267 - Deep Chrome Green
  • BS280 - Verdigris Green
  • BS284 - Aircraft Grey Green
  • BS285 - Spruce Green
  • BS298 - Olive Drab
  • BS309 - Canary Yellow
  • BS310 - Primrose
  • BS315 - Grapefruit
  • BS320 - Light Brown
  • BS337 - Very Dark Drab
  • BS352 - Pale Cream
  • BS353 - Deep Cream
  • BS355 - Lemon
  • BS356 - Golden Yellow
  • BS358 - Light Buff
  • BS361 - Light Stone
  • BS363 - Bold Yellow
  • BS365 - Vellum
  • BS366 - Light Beige
  • BS367 - Manilla
  • BS369 - Biscuit
  • BS380 - Camouflage Desert Sand
  • BS384 - Light Straw
  • BS388 - Beige
  • BS389 - Camouflage Beige
  • BS411 - Middle Brown
  • BS412 - Dark Brown
  • BS414 - Golden Brown
  • BS420 - Dark Camouflage Desert Sand
  • BS436 - Dark Camouflage Brown
  • BS445 - Venetian Red
  • BS447 - Salmon Pink
  • BS453 - Shell Pink
  • BS454 - Pale Roundel Red
  • BS499 - Service Brown
  • BS537 - Signal Red
  • BS538 - Cherry
  • BS539 - Currant Red
  • BS541 - Maroon
  • BS542 - Ruby
  • BS557 - Light Orange
  • BS564 - Bold Red
  • BS568 - Apricot
  • BS592 - International Orange
  • BS593 - Rail Red
  • BS626 - Camouflage Grey
  • BS627 - Light Aircraft Grey
  • BS629 - Dark Camouflage Grey
  • BS630 - French Grey
  • BS631 - Light Grey
  • BS632 - Dark Admiralty Grey
  • BS637 - Medium Sea Grey
  • BS638 - Dark Sea Grey
  • BS642 - Night
  • BS676 - Light Weatherwork Grey
  • BS677 - Dark Weatherwork Grey
  • BS692 - Smoke Grey
  • BS693 - Aircraft Grey
  • BS694 - Dove Grey
  • BS697 - Light Admiralty Grey
  • BS796 - Dark Violet
  • BS797 - Light Violet
Size
Finish
£79.72
VAT excluded

£95.66 Tax incl.
Quantity

Description

SigmaCover 400/Amerlock 400 is a two-component, high solids epoxy coating for steel and concrete, galvanising, stainless steel and non-ferrous metals. The coating has good adhesion on existing coats and is compatible with prepared, damp surfaces.

Available in black, Persian Grey (BS 00A05), white, and the full RAL and BS range (more than 350 colours).



Product Qualifications


  • Compliant with USDA Incidental Food Contact Requirements
  • NFPA Class A for Flame Spread and Smoke Development
  • Qualified for ANSI/NSF Standard 61 (potable water) for valves only. For NSF application instructions, please visit the NSF website
  • MPI Category #108
  • Nuclear Service Level 2 (ANSI N 5.12, ANSI N 101.2)
  • LEED’s compliant for Anti-corrosive Paint category



Features & Benefits


  • Available in 350+ colours from RAL & BS
  • High performance self priming universal epoxy
  • High solids, low VOC
  • Surface tolerant and abrasion resistant
  • Compatible with prepared, damp surfaces
  • Good adhesion on most existing coatings
  • Temperature resistant up to 120°C (250°F)
  • Available in MIO or conventional pigmented grade
  • Good resistance to splash and spillage of chemicals
  • Meets NSF Standard 61 for valves
  • No induction time
  • 2 hours pot life
  • Touch dry in 6 hours
  • Fully cured after 7 days
  • Can be applied by air spray, brush or roller
  • See below for more information on surface preparation, application details and curing times

 

Reference Colour Size Gloss Level
312060 Black 20 litres Semi-Gloss
331890 Persian Grey (BS 00A05) 4 litres Semi-Gloss
331889 Persian Grey (BS 00A05) 20 litres Semi-Gloss
331888 White 4 litres Semi-Gloss
331887 White 20 litres Semi-Gloss
331900 Full RAL & BS colours 4 litres Semi-Gloss
331899 Full RAL & BS colours 20 litres Semi-Gloss

Note:

  • Epoxy coatings will chalk and fade with exposure to sunlight. Light colors are prone to ambering to some extent. Note that product tinted to custom colors are not recommended for immersion service. Only use factory grind batches for immersion



Product Data


Two-component, high-build polyamide cured anticorrosive epoxy primer/coating.

Data for mixed product at 20°C (68°F)
Number of components Two
Mass density 1.4 kg/l (11.7 lb/US gal)
Volume solids 85 ± 2%
VOC (Supplied) Directive 1999/13/EC, SED: max. 114.0 g/kg
max. 163.0 g/l (approx. 1.4 lb/US gal)
EPA Method 24: 180.0 g/ltr (1.5 lb/USgal)
Temperature resistance (Continuous) To 120°C (250°F)
Temperature resistance (Intermittent) To 175°C (350°F)
Recommended dry film thickness 100 - 200 µm (4.0 - 8.0 mils)
Theoretical spreading rate 8.5 m²/l for 100 µm (341 ft²/US gal for 4.0 mils)
Dry to touch 6 hours
Overcoating Interval Minimum: 16 hours
Maximum: See overcoating tables below
Full cure after 7 days
Shelf life Base: at least 36 months when stored cool and dry
Hardener: at least 36 months when stored cool and dry

Notes:

  • Intermittent temperature resistance should be less than 5% of the time, and maximum 24 hours
  • Temperature resistance is in atmospheric condition. Please contact Rawlins Paints Technical for immersion condition



Surface Preparation


Recommended Substrate Conditions and Temperatures

Substrate conditions

  • Coating performance is proportional to the degree of surface preparation. Remove all loose paint, mill scale, and rust
  • The surface to be coated must be dimensionally stable, dry, clean and free of grease, oil, and other foreign materials
  • When proper abrasive blast surface preparation is not practical, surfaces should be chipped clean and wire brushed to bare, clean material

 

Carbon Steel

  • For immersion service: steel; blast cleaned to ISO-Sa2½ (SSPC SP-10)
  • For atmospheric service, abrasive blast to ISO-Sa2½ or minimum SSPC SP-6, power tool cleaned to ISO-St3 (SSPC SP-3) or hand tool cleaned to ISO-St2 (SSPC SP-2) or ultra high pressure water jet to SSPC SP WJ-2(L) / NACE WJ-2(L)

 

Concrete / Masonry

  • Remove grease, oil and other penetrating contaminants according to ASTM D4258
  • Abrade the surface per ASTM D4259 to remove all chalk and surface glaze or laitance. Achieve surface profile - ICRI CSP 3 to 5
  • Fill voids as necessary with AMERCOAT 114 A epoxy filler
  • Maximum recommended moisture transmission rate is 3 lbs / 1,000 ft2 / 24 hours by moisture transmission test (ASTM F1869, calcium chloride test or by ASTM D4263, plastic sheet test)
  • Alternatively, ASTM D4944 (Calcium Carbide Gas method) can be used, moisture content should not exceed 4%

 

Galvanized steel

  • Remove oil or soap film with detergent or emulsion cleaner
  • Lightly abrasive blast with a fine abrasive in accordance with SSPC SP-16 guidelines to achieve a profile of 40 - 75 µm (1.5 - 3.0 mils). When light abrasive blasting is not possible, galvanizing can be treated with a suitable zinc phosphate conversion coating
  • Galvanizing that has had at least 12 months of exterior weathering may be coated after power washing to remove all contaminants and white rust

 

Non-ferrous metals and stainless steel

  • Remove all rust, dirt, moisture, grease or other contaminants from the surface
  • Lightly abrasive blast with a fine abrasive in accordance with SSPC SP-16 guidelines to achieve a profile of 40 - 100 µm (1.5 - 4.0 mils)

 

Aged coatings and repairs

  • Aged suitable coating must be dry and free from any contamination
  • For single-pack coatings, extra precautions are necessary

 

Substrate Temperature & Application Conditions


  • Substrate temperature during application and curing should be between 5°C (41°F) and 50°C (122°F)
  • Substrate temperature during application and curing should be at least 3°C (5°F) above dew point



System Specification


Primers:

  • Direct to substrate
    • DIMETCOTE Series
    • AMERCOAT 68 Series
    • AMERLOCK 2 / 400 Series
    • SIGMAZINC Series
    • AMERCOAT Epoxies
    • SIGMA Epoxies

Topcoats:

  • AMERCOAT 450 Series
  • SIGMADUR Series
  • SIGMACOVER Epoxies
  • AMERCOAT Epoxies
  • AMERSHIELD
  • PSX 700



Application


Instructions for Use

Mixing ratio by volume: base to hardener 50:50 (1:1)

  • The paint should be stirred well before use, preferably by means of a mechanical mixer, to ensure homogeneity
  • Add hardener to base and continue stirring until homogeneous

 

Induction Time


None.

 

Pot life


  • 2 hours at 20°C (68°F)

Refer below for more information

 

Air Spray


Recommended thinner

  • THINNER 91-92 FOR GLOBAL
  • THINNER 21-06 (AMERCOAT 65) FOR NSF/ANSI 61
  • THINNER 21-25 (AMERCOAT 101) for NON NSF/ANSI 61 and > 90°F (32°C)

Volume of thinner

  • 0 - 10%, depending on required thickness and application conditions

 

Airless spray


Recommended thinner

  • THINNER 91-92 FOR GLOBAL
  • THINNER 21-06 (AMERCOAT 65) FOR NSF/ANSI 61
  • THINNER 21-25 (AMERCOAT 101) for NON NSF/ANSI 61 and > 90°F (32°C)

Volume of thinner

  • 0 - 5%, depending on required thickness and application conditions

Nozzle orifice

  • Approx. 0.48 mm (0.019 in)

Nozzle pressure

  • 15.0 - 18.0 MPa (approx. 150 - 180 bar; 2176 - 2611 p.s.i.)

 

Brush/roller


Recommended thinner

  • Brush: apply evenly using a clean, well-loaded brush
  • Application by brush or roller will provide approximately 80 µm (3.1 mils) DFT in a single-coat application

 

Cleaning Solvent




Spreading Rate and Film Thickness


DFT Theoretical spreading rate
100 µm (4.0 mils) 8.5 m²/l (341 ft²/US gal)
125 µm (5.0 mils) 6.8 m²/l (273 ft²/US gal)
200 µm (8.0 mils) 4.3 m²/l (170 ft²/US gal)



Overcoating interval for DFT up to 125 µm (5.0 mils)


Overcoating with... Interval 10°C (50°F) 20°C (68°F) 30°C (86°F) 40°C (104°F)
Itself and various twopack epoxy coatings Minimum 36 hours 16 hours 6 hours 4 hours
Maximum 3 months 3 months 2 months 1 month
Urethane and PSX Minimum 36 hours 16 hours 6 hours 4 hours
Maximum 1 months 1 months 14 days 7 days

Note:

  • PPG 861 (AMERCOAT 861) accelerator (1 pint per 5 gallons) will reduce min. and max. recoat interval to half (US supply only)
  • Surface should be dry and free from any contamination
  • A detergent wash with PREP 88, SIGMARITE 88 or equivalent is required prior to application of topcoats after 30 days of exposure
  • If maximum recoat time has been exceeded, roughen surfaces
  • Alkyd coatings and waterborne acrylic coatings should be applied after the film is dry to handle and not greater than three times dry to handle time
  • Maximum recoating time is highly dependent upon actual surface temperature - not simply air temperatures. Sun-exposed or otherwise heated surface will shorten the maximum recoat window

 

Curing time for DFT up to 125 µm (5.0 mils)


Substrate temperature Dry to touch Dry to Handle Full Cure
10°C (50°F) 24 hours 48 hours 21 days
20°C (68°F) 6 hours 20 hours 7 days
30°C (86°F) 3 hours 12 hours 4 days
40°C (104°F) 1 hour 8 hours 3 days

Notes:

  • Adequate ventilation must be maintained during application and curing (please refer to information sheets 1433 and (1434)
  • PPG 861 (AMERCOAT 861) accelerator (1 pint per 5 gallons) will reduce curing time to half

 

Pot Life (at application viscosity)


Mixed product temperature Pot life
10°C (50°F) 3 hours
21°C (70°F) 2 hours
32°C (90°F) 1 hour
40°C (104°F) 30 minutes

Note:

  • PPG 861 (AMERCOAT 861) accelerator (1 pint per 5 gallons) will reduce pot life to half



Safety Precautions


  • For paint and recommended thinners, see information sheets information sheet 1430, information sheet 1431 and the relevant Material Safety Data Sheets in the attachments section above
  • This is a solvent-borne paint and care should be taken to avoid inhalation of spray mist or vapor, as well as contact between the wet paint and exposed skin or eyes



References


It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
331922

Data sheet

Manufacturer
PPG
Parts
Two
Base Type
Epoxy
Solvent
Solvent-based
Mixing Ratio
1:1
Suitable Substrates
Steel, concrete
Key Features
Temperature resistant up to 120°C (250°F)
Application
Brush, Roller, Spray
Touch Dry (at 20°C)
6 hours
Dry to Handle (at 20°C)
2 hours
Dry to Recoat (at 20°C)
16 hours
Fully Cured (at 20°C)
7 days
Pot Life (at 20°C)
2 hours
Coverage
8.5 m²/l for 100 µm
Recommended Thinner/Cleaner
91-92, 21-06, 21-25, 90-53, 90-58.
Unit Contents
Base & hardener
Compatible Primers
DIMETCOTE, AMERCOAT 68, AMERLOCK 2 / 400, SIGMAZINC, AMERCOAT Epoxies, SIGMA Epoxies
Compatible Topcoats
AMERCOAT 450, SIGMADUR, SIGMACOVER Epoxies, AMERCOAT Epoxies, AMERSHIELD, PSX 700
Max. Application Temperature
50°C (122°F)
Min. Application Temperature
5°C (41°F)
Density
1.4 kg/l (11.7 lb/US gal)
Solids by Volume
85 ± 2%
Heat Resistance (up-to)
To 120°C (250°F)
VOC
Directive 1999/13/EC, SED: max. 114.0 g/kg max. 163.0 g/l (approx. 1.4 lb/US gal) EPA Method 24: 180.0 g/ltr (1.5 lb/USgal)
Shelf Life (from date of manufacture)
Base: 36 months, hardener 36 months
UN Number (Activator)
UN3469
UN Number (Base)
UN1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

PPG Thinner 21-06

This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.

Price £38.45
In stock

PPG Thinner 90-53

This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.

Price £38.45
In stock

PPG Thinner 90-58

This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.

Price £33.95
In stock

PPG Thinner 91-92

This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.

Price £36.20
In stock
16 other products in the same category:

Jotun Hardtop One

Jotun Hardtop One is a one component moisture curing acrylic polysiloxane resin based coating. The product does not contain isocyanates, neither does it generate di-isocyanates during hotwork / welding or fire accidents. It has excellent gloss and colour retention. It is a high solids product. The product is fully recoatable at any stage of...

Price £100.67
In stock

Sherwin-Williams Acrolon C237

Sherwin-Williams Acrolon C237 (formerly Acrolon C237) is a high performance fast drying acrylic urethane sheen finish for use where long term exterior colour retention characteristics are required. It is suitable for use as final coat or coats in conjunction with epoxy or polyurethane based protective systems for new construction or...

Price £79.94
In stock

HMG C71 Speedline

HMG C71 Speedline is a  high quality '2 hour' drying time synthetic alkyd enamel.  It offers fast surface drying, good through drying even in thick films and outstanding film hardness and toughness.  In addition, yellowing is minimal even after prolonged exposure to higher temperatures. Quick drying agricultural paint. Quick drying...

Price £17.97
In stock

Cromadex 400 One Pack Lower Polyurethane Topcoat Aerosol

Cromadex 400 One Pack Lower Polyurethane Topcoat Aerosol is intended for touch up work on exterior metal. It has a long wet edge, is exterior durable, is lead and chromate-free and is available in 4 gloss levels. Over 350 colours available from RAL & BS NCS, metallic, sparkles and special matches may be available on request Contact...

Price £50.83 Regular price £101.66
In stock

International Intergard 1735

International Intergard 1735 is a high performance, low VOC, water borne two component epoxy with a high gloss finish. International Intergard 1735 is a tough, hard wearing chemically resistant epoxy finish suitable for most circumstances where the odour or emissions from solvent based coatings are unacceptable. Coverage Calculator

Price £101.67
In stock

Axalta ViterThane PLS Recoatable PU Finish

Axalta ViterThane PLS Recoatable PU Finish, A two pack recoatable polyurethane semi-gloss finish for use on protective systems for steelwork. Excellent colour retention and indefinitely overcoatable. Excellent chemical resistance and low temperature cure. An aliphatic polyurethane providing a tough and durable semi-gloss finish with...

Price £78.89
In stock

Bradite One Can

Bradite One Can is a quick-drying primer/finish coat in one can, with excellent adhesion, stain blocking and anti-corrosive properties. Suitable for use over most properly cleaned and prepared commercial wood, uPVC, glass, plastic and metals. Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004. Advantages Available in...

Price £19.95
In stock

Zinga Zingatarfree

Zingatarfree (Formally PU Tarfree MIO) is ideal for marine environments and immersion, such boat hulls, with excellent water, corrosion and chemical resistance, and can be used as a replacement for normal coal tar products Single-pack polyurethane paint Use as part of a duplex system with Zinga Apply by brush, roller, conventional...

Price £23.55
In stock

PPG AquaCover 40

PPG AquaCover 40 (also known as Sigma Aquacover 40) is a one-component, waterborne acrylic dispersion finish with good weather resistance and excellent adhesion to primed steel. Particularly suitable when solvents are not permitted because of health and safety reasons Good weather resistance Good colour retention Not suitable for...

Price £55.90
In stock

Teamac Extra Brilliant Aluminium Paint

Teamac Extra Brilliant Aluminium Paint, is an all metal coating with thermal and photo reflective properties that can be used as a heat and light reflective protective finish on car wheels, hot water pipes, radiators, metal car components.  It provides heat resistance up to 150°C. Advantages Thermally reflective Photo reflective...

Price £19.43
In stock

Jotun Pilot II

Jotun Pilot II is a one component oxidatively drying alkyd coating from Jotun that has a gloss finish with good gloss retention. To be used as a topcoat in atmospheric environments. Jotun Pilot II is recommended as a topcoat, and for touch-up purposes for marine engines, topside, deck and superstructure areas and for a wide range of...

Price £44.04
In stock

Tor Quick Drying Machinery Enamel

Tor Quick Drying Machinery Enamel finishes factory machinery, tools, agricultural implements, etc, applying by airless spray. Available in over 400 colours from RAL and BS. Quick drying Touch dry in 30 minutes Hard dry after 2 hours An alkyd resin binder pigmented with inorganic pigments and thinned with xylene Use with a suitable...

Price £14.19
In stock

Rust-Oleum 5500 Solvent Free Epoxy

Rust-Oleum 5500 Solvent Free Epoxy is a high build, solvent-free epoxy floor paint for garages, warehouses, showrooms, corridors, indoor car parks, workshops etc. Optimal protection in only one or two layers. High build coating (150 microns), very durable Suitable for frequent (chemical) cleaning Excellent resistance against immersion...

Price £128.38
In stock

Cromadex 440 One Pack Lower Odour Polyurethane Fine Texture Topcoat

Cromadex 440 One Pack Lower Odour Polyurethane Fine Texture Topcoat is a one pack lower odour topcoat that comes in a fine texture finish that adds value to your product. The product uses polyurethane technology providing excellent colour retention. The product has a long wet edge making it easier to apply to large items with no dry spray.

Price £77.48
In stock

Blackfriar Enamel Paint

Blackfriar Enamel Paint is a tough, hard-wearing gloss enamel finish. Suitable for use on wood, metal and plaster. Ideal for garden tools, plaques and models. Product Features Long lasting finish Tough and durable For use on wood, metal and plaster High gloss Interior and exterior use Solvent-based

Price £6.40
In stock

Cromadex 400 One Pack Lower Odour Polyurethane Topcoat

Cromadex 400 One Pack Lower Odour Polyurethane Topcoat is a one pack lower odour topcoat using polyurethane technology providing excellent gloss and colour retention. The product is an automotive standard product with proven performance. The product has a long wet edge making it easier to apply to large items with no dry spray.

Price £77.48
In stock