HMG QAD Enamel is an industrial, durable, high gloss, tough alkyd for use on spray applied steel, railings, exterior furniture and fencing plus other suitable prepared metals.
Quick drying - touch dry in 30 minutes
Coverage: 11-12m² per litre at 20 microns dft, 10-12 m² per litre at 55 microns dft
Can be applied to mild, galvanised and shot blasted steel substrates
Rust/corrosion to be removed to Sa or St standards, remove to clean metallic appearance with little or no rust/corrosion present
Bare substrates
Mild steel – Remove millscale and thoroughly degrease using suitable HMG Prep Clean
Abrade with P80 – P180 if necessary, prior to application of primer
Shot Blasted Steel – Remove all traces of blast grit/sand prior to application of primer
Aluminium – Abrade with P180 – P320, degrease with suitable HMG Prep Clean prior to application of primer
Galvanised Steel – Degrease with suitable HMG Prep Clean, apply HMG Mordant Wash, apply HMG Etch Primer and if required HMG Primer
Previously Painted
High pressure wash to remove all loose debris and poorly adhered previous coatings to remove all salts and other contaminants
Degrease using suitable HMG Degreaser 2800 to remove grease and oils not removed with pressure washing alone
Existing coatings to be well adhered with all edges tight and well feathered
Rust/corrosion to be removed back to clean metallic appearance
Abrade to provide good adhesion
Wipe over with degreaser to remove loose debris from abrasion
Substrate to be clean, free of grease, oils, dust and completely dry prior to application
For further assistance contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information
Health & Safety
Refer to the safety data sheet in the attachments section above and tin label prior to use
Suitable respiratory equipment should be worn when spraying
Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with water and disposed of in a noncombustible container with a tight fitting lid
Product Details
4345-1036186
Data sheet
Manufacturer
HMG Paints Limited
For Use By
Professional Use
Interior / Exterior Use
Exterior Use
For Use On
Steel Metal Railings Exterior Furniture Metal Fencing
Application Method
Spray
Sheen
Satin Matt Gloss
Single, Two or Three Pack
Single
Pack Size
1L 5L 20L
Touch Dry (at 20°C)
30 Mins
Dry to Handle (at 20°C)
12 Hours
Dry to Recoat (at 20°C)
16 Hours Minimum
Fully Cured (at 20°C)
24 Hours
Coverage
11-12m²/L at 20 microns dft 10-12 m² per litre at 55 microns dft
Recommended Thinner/Cleaner
HMG Thinner 2621/2622
Density
0.976 g/cm³
Solids by Volume
44.5 %
VOC
540g/L
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG QAD Enamel is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
HMG Speedbuild 3 Primer is a 1K, high build, high solids, anti-corrosive primer. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener/thinner:2-Pack System DetailsBase (Part 1) HMG Speedbuild 3 PrimerThinner (Part 2) HMG Thinner 2601HMG Thinner 2602HMG...
HMG QAD Enamel Aerosol is an industrial, durable, high gloss, tough alkyd for use on spray applied steel, railings, exterior furniture and fencing plus other suitable prepared metals. For the non-aerosol version of this product please see HMG QAD Enamel400ml/16oz Aerosol Available in packs of 1 or packs of 6+, 50 and 100 with discounted...
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...