HMG Aquaguard 2

    TOPAQUA2WHT
    HMG4411

    HMG Aquaguard 2 is a high quality water based 2K epoxy system.

    This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:

    2-Pack System Details
    Base (Part 1)HMG Aquaguard 2
    Activator (Part 2)HMG Hardener 9110

    • Part one of a two part pack
    • Good long term durability
    • Good chemical resistance

    Colour
    Size
    Finish
    £211.71(ex. VAT)
    £254.05 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    HMG Aquaguard 2 is a high quality Water Based 2K epoxy system.

    Please note this product is one part of a two-pack system which MUST be purchased/used together with HMG Hardener 9110.

    Click To Jump To Section:




    Features & Benefits


    • Good long term durability
    • Good chemical resistance



    Product Specification


    Technical Data
    Volume Solids:72.4%
    VOC Content:0.006 base onlyKg/L
    SG:-
    Viscosity:8460 mPas
    Density:1.639 g/cm³
    Storage Conditions:Store between 5°C - 25°C. When not in use, cans must be kept sealed.
    Shelf Life:6 months from delivery date in original sealed containers.
    Pot Life:1.5 hours at 20°C. Possible problems after this time.
    Flash Point:n/a



    • Pot Life - No discernable increase in viscocity.  If pot life exceeded, adhesion failures will occur.

    Film Thickness Range And Coverage


    Product Data
     Dry Film ThicknessWet Film Thickness
    Compliant Spry Gun:35 - 50 μm88 - 125 μm
    HVLP:35 - 50 μm88 - 125 μm
    Roller:35 - 50 μm88 - 125 μm
    Brush:35 - 50 μm88 - 125 μm



    Coverage: 8 square metres per litre @ 40 microns dft.

    • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
    • These values are a guide only and are not to be used as specifications.
    • Film thickness will vary depending on actual use and specification.
    • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



    Drying Times


    Drying Times At 20°C
    Touch Dry:3 hours
    Dry To Handle:24 hours
    Dry To Recoat:1.5 hours at 20°C. Possible problems after this time.
    Fully Cured:5 days



    Surface Preparation


    • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
    • Read and follow the safety data sheet, product data sheet and label instructions.
    • Stir all paints thoroughly before use.
    • Always use the same batch number on the same job.
    • Check colour & sheen.
    • Filter the product immediately before use.
    • Reduce emissions and maintain quality by replacing tin lid after use.



    Application Methods


    Technical Data
    Compliant Spray GunHVLPRollerBrush
    Mixing Ratio:Base: 1Base: 1Base: 1Base: 1
    Hardener: 2Hardener: 2Hardener: 2Hardener: 2
    Thinner: Up to 10%Thinner: Up to 10%Thinner: Up to 10%Thinner: Up to 10%
    Hardener Options:Hardener 9110Hardener 9110Hardener 9110Hardener 9110
    Thinner Options:WaterWaterWaterWater
    Viscosity:70 - 80 seconds B4 cup Ready for use70 - 80 seconds B4 cup Ready for use--
    Spray Gun Setup:1.6 - 1.81.6 - 1.8--
    Number Of Coats (Guide Only):1 - 2 full coats1 - 2 full coats1 - 2 full coats1 - 2 full coats
    Flash Off:----



    For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



    Product Notes


    Information On Basic Physical And Chemical Properties
    Form:Liquid
    Colour:White
    Odour:Characteristic
    Odour Threshold:Not determined
    pH-value 20°C:Not determined
    Change in Condition
    Melting point/freezing point:0°C
    Initial boiling point and boiling range:100°C
    Flash Point:Not applicable
    Flammability (solid, gas):Not applicable
    Ignition temperature:Product is not selfigniting.
    Decomposition temperature:Not determined.
    Auto-ignition temperature:Product is not selfigniting
    Explosive properties:"Product is not explosive. However, formation of explosive air vapour mixtures are possible."
    Explosion limits: Lower:Not determined
    Explosion limits: Upper:Not determined
    Vapour pressure at 20°C:23 hPa
    Bulk Density at 20°C:1 kg/m³
    Density at 20°C:1.639 g/cm³
    Relative density:Not determined
    Vapour density:Not determined
    Evaporation rate:Not determined
    Solubility in / Miscibility with water:NOT MISCIBLE
    Partition coefficient: n-octanol/water:Not determined
    Viscosity: Dynamic at 20°C:180 mPas
    Viscosity: Kinematic:Not determined
    Solvent content: Organic solvents:0.1% - Water: 23.7%
    Solids content:72.4%



    Health & Safety


    • Refer to the safety data sheet in the attachments section above and tin label prior to use.
    • Suitable respiratory equipment should be worn when spraying.

    Click to go back to the top of the page

    Product Details
    4411-670889

    Data sheet

    Manufacturer
    HMG Paints Limited
    For Use On
    Metal
    Application Method
    Brush, Roller, Spray
    Sheen
    Gloss
    Colour
    Standard / Ready Mixed
    VOC Levels
    Ultra-Low (5-49 g/l)
    Single, Two or Three Pack
    Two-Pack
    Pack Size
    7.5L
    Base Type
    Water based
    Mixing Ratio
    Base: 1 - Hardener: 2 - Thinner: Up to 10%
    Touch Dry (at 20°C)
    3 hours
    Dry to Handle (at 20°C)
    24 Hours
    Dry to Recoat (at 20°C)
    1.5hrs @ 20°C possible problems after this time.
    Fully Cured (at 20°C)
    5 Days
    Pot Life (at 20°C)
    1.5hrs @ 20°C possible problems after this time.
    Coverage
    8 square metres per litre @ 40 microns dft
    Recommended Thinner/Cleaner
    Water
    Density
    1.639 g/cm³
    Solids by Volume
    72.4 %
    Heat Resistance (up-to)
    80 °C
    VOC
    0.006 base only Kg/l
    Shelf Life (from date of manufacture)
    6 months from delivery date in original sealed containers
    Recommended Dry Film Thickness
    35 - 50 μm
    Recommended Wet Film Thickness
    88 - 125 μm
    UN Number
    Not regulated
    Base Type
    Water-Based
    Suitable For Use On
    Primed Surfaces
    Suitable For Use On
    Metal
    Finish
    Gloss
    Application Method
    Roller
    Application Method
    Brush
    Application Method
    Spray
    Usages
    Chemical Resistance
    Usages
    Tough/Durable
    Usages
    Atmospheric
    Product Usage Type
    Topcoat
    Colour Family
    White
    Product Type
    Acrylic
    Environment
    Atmospheric
    Touch Dry/Dust Free (@ 20-25°C)
    3 hours
    Product Attributes
    Tough / Durable
    Product Attributes
    High Solids
    Resistance to
    Chemicals
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    HMG Aquaguard 2 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    HMG Hardener 9100

    HMG Hardener 9100 is a high solids 2K water based isocyanate hardener for use with HMG Hydrothane. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) HMG HydrothaneActivator (Part 2) HMG Hardener 9100Part two of a...

    In stock

    Surface Preparation Kits for Steel

    These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...

    Price £21.53 (ex. VAT)
    In Stock and Available for Delivery