A specially formulated blend of solvents designed to mix with its compatible Teamac or Coo-Var coating to create an optimal consistancy for application. Suitable for use with Brush, Roller or Spray. Teamac Thinner 14 can also be used for the cleaning of some surfaces prior to application of the coating. Also suitable for the cleaning of...
Teamac Metalcote Plant Enamel
Teamac Metalcote Plant Enamel, is a tough, flexible enamel paint with an attractive gloss finish and excellent durability. It has good resistance to lubricating, mineral oils, many common industrial chemicals and heat.
- Good resistance to oils, chemicals and heat
- Ideal for use on all types of machinery including tractors.
- Click to jump down to Technical Data
Teamac Metalcote Plant Enamel is a tough, flexible enamel paint with an attractive gloss finish and excellent durability. It has good resistance to lubricating, mineral oils, many common industrial chemicals and heat.
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Preceeding Coat
- Application Conditions
- Application Methods
- Health & Safety
Features & Benefits
- Good resistance to oils, chemicals and heat.
- Ideal for use on all types of machinery including tractors.
- Click to jump down to Technical Data
|Volume Solids||Approx 35%|
|VOC Content||Max 550 g/litre|
|SG||0.91 to 1.08 °C|
|Viscostity||3.0 Poise @ 25 °C|
|Flash Point||Above 32°C (closed cup)|
Film Thickness Range And Coverage
|Dry Film Thickness||Wet Film Thickness||Theoretical Coverage|
|Maximum||35 to 40 μm||85 μm||12 m12/litre @ 35 microns D.F.T|
The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.
|Drying Times At 20°C/RH 50%|
|Touch Dry:||2 Hours|
|Dry To Handle:||8 Hours|
|Dry To Recoat:||8 Hours or overnight|
|Fully Cured:||3 - 5 Days|
Low temperature and high humidity will adversely affect application, drying and performance of any coating.
- All surfaces should be clean, dry, sound and free from contaminants.
- Existing painted surfaces should be cleaned, degreased and sanded to ensure an adequate "key" is produced.
- Remove all loose, flaking material and treat bare areas as new substrate then prepare accordingly.
- Teamac Metalcote Undercoat
- Mix well before use.
- As dictated by normal good painting practice.
- Care must be taken during application that the temperature is above the dew point to avoid any contamination.
- In confined spaces, provide adequate ventilation during application and drying.
|Method||Airless Spray||Conventional Spray||Brush||Roller|
- Thinner (Max vol): Thinners 14 (10%)
- Nozzle Size: 0.011"
- Nozzle Pressure: 1800 to 2000 psi
- Cleaning Solvent: Thinners 14
Health & Safety
See safety data sheet - White - SDS 10719, Black - SDS 10720, Reds and Maroons - SDS 10723, Deutz Silver - SDS 11005, Lead Chrome Yellows (Professional use only) - SDS 10722, All other Lead Chrome free colours - SDS 10721. TAL, TBL and TDL tinting bases - SDS 11071, Tyel and Tred tinting bases - SDS 11072 in attachments section above.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Key Features
- Good resistance to oils, chemicals and heat. Ideal for use on all types of machinery including tractors.
- Brush, Roller, Spray
- Dry to Handle (at 20°C)
- 8 Hours
- Dry to Recoat (at 20°C)
- 8 Hours or overnight
- Fully Cured (at 20°C)
- 3 - 5 Days
- 12 m12/litre
- Recommended Thinner/Cleaner
- Teamac Thinner 14
- Solids by Volume
- Approx 35%
- Max 550 g/litre
- Touch Dry
- 2 Hours
- 1 litre, 2.5 litre, 5 litre
- Recommended Dry Film Thickness
- 35 to 40 μm
- Recommended Wet Film Thickness
- 85 μm
- UN Number
|David Smith on 22/10/2018|| |
I am refurbishing a Belle cement mixer. I have removed all flaking paint and keyed original paintwork and primed all surfaces as well as bare metalwork with a grey acrylic spray primer. I want to apply further paintwork by brush as spraying is messy.I feel that your Teamac Metalcote would be good, however should i need to use your suggested undercoat before applying the top coats of gloss RAL 2004.
Teamac Metalcote Undercoat could be used prior to application of Teamac Metalcote Plant Enamel and would improve the finish/durability of the finished system but should you choose to, Teamac Metalcote Plant Enamel could be applied directly to your previously painted, prepared surfaces.
|C.Hallam on 17/04/2018|| |
Can you use Teamac Metalcote Plant Enamel onRust-Oleum 3202 Galvinoleum primer
No, only Rust-Oleum 7500 Alkythane can be used to overcoat Rust-Oleum 3202 Galvinoleum Primer.
|neil buckland on 17/07/2017|| |
Question: What type of Thinner do I require for the Teamac Zinc Phosphate Primer and Teamac Metal Coat Enamel. Can they be thinned with water or do I require a solvent Thinner.
|C. Flintan on 26/02/2016|| |
Can I use Teamac Metalcote Plant Enamel on top of Teamac Zinc Rich Primer?
|kevin on 18/08/2015|| |
Can I paint an engine with Teamac Metalcote Plant Enamel?
Yes, as long as any bare metal is primed with an appropriate Teamac primer and whatever is painted does not exceed a maximum temperature of 80°C.
Sherwin-Williams Acrolon C237 (formerly Acrolon C237) is a high performance fast drying acrylic urethane sheen finish for use where long term exterior colour retention characteristics are required. It is suitable for use as final coat or coats in conjunction with epoxy or polyurethane based protective systems for new construction or maintenance purposes
Blackfriar Metallic Paint is a bright metallic finish for decorating and gilding ornamental plasterwork, wood, metal railings, picture frames, models, fleur-de-lis, memorabilia & furniture. Product Features Washable surface Tough & durable Interior and exterior use Fast drying Water-based
Sherwin-Williams Macropoxy M330 (formerly known as Epigrip M330) is a 2-pack epoxy sealercoat for use over zinc silicate and other types of zinc rich primers. It is also used as a blast primer for use over stainless steel.
Nu-Steel TP Finish is the final coat of the Nu-Steel TP System, providing an excellent decorative appearance and outstanding resistance to solvents and chemicals, making it a first choice coating system for use on steelwork. Advantages Available in any RAL colour. Up to 15 years protection. 11m²/Litre approx. coverage. Touch-dry in 3 hours.
International Interfine 878 is a high performance, two component, high solids finish which contains no free isocyanates, offers compliance to current VOC legislation, and affords extended lifetime to first maintenance when utilised as part of a high performance anticorrosive system.
Jotun Hardtop HB is a two component chemically curing aliphatic acrylic polyurethane coating that has a matt finish with very good gloss retention. It is a high build product that can be used as a topcoat in atmospheric environments. Jotun Hardtop HB is recommended for topside, deck and superstructure areas in the marine industry.
Cromadex 310 Low Bake Stoving Topcoat is a low bake stoving topcoat that contains melamine to give it a tough durable finish. The lower stoving schedule of the product can help in reducing overall heating costs. The unique resin and pigment technology used enables both a wide variety of applications and a durable finish. Available in all BS and RAL colours.
Bradite HB MIO Coat/Finish is a high build high performance single pack modified alkyd micaceous iron oxide intermediate coat. Gives excellent decorative anti-corrosive properties when used as a coating or finish in a conventional paint system. Conforms to MOD TS10201 specification & BS5493 parts FU2C/FF3D. Advantages Good toughness...
Cromadex 642 Two Pack Polyurethane Medium Texture Topcoat is a two pack polyurethane medium texture topcoat with excellent exterior durability and chemical resistance. The product offers a medium texture appearance for an aesthetic finish. Demonstrates good mar resistance, ideal if the end product is to be widely handled. The addition of Rapidcure can...
Rust-Oleum 7500 Alkythane is a single pack high performance, anti-corrosion topcoat for metal. Ideal for low temperatures (as low as 5°C) it offers the same protection in less layers than other alkyd-systems. Available in 400+ colours Excellent opacity and corrosion protection Easy to apply, excellent flow and aspect Extra durable...
International Interthane 990 is a two component acrylic polyurethane finish giving excellent durability and long term recoatability. Across the world, people are experiencing flexible application, extended recoat windows and reduced surface preparation costs with International Interthane 990 in both new construction and as a maintenance finish.
Cromadex 440 One Pack Lower Odour Polyurethane Fine Texture Topcoat is a one pack lower odour topcoat that comes in a fine texture finish that adds value to your product. The product uses polyurethane technology providing excellent colour retention. The product has a long wet edge making it easier to apply to large items with no dry spray.
Cromadex 840 Two Pack Non-Isocyanate Acrylic Fine Texture Topcoat is a two pack non-isocyanate acrylic fine texture topcoat with excellent exterior durability and chemical resistance. The product uses unique resin and pigment technology enable a wide variety of applications and a durable finish, whilst the fine texture appearance offers an aesthetic finish.
Cromadex 742 Two Pack Epoxy Medium Texture Topcoat is a two pack epoxy medium texture topcoat with excellent chemical resistance for interior use only. The product offers a medium texture appearance for an aesthetic finish. The product can be air dried or stoved enabling flexibility in production. Available in a wide range of colours and gloss...
Rust-Oleum 9200 Rust-O-Thane is a satin, water based polyurethane for a very durable and colourfast finish on coated floors, walls and primed metal. Especially recommended where general urethane performance like excellent weather resistance (UV), easy cleaning and abrasion resistance is required. Rust-Oleum's hard wearing, washable...