Tikkurila Temadur 10 can be used as a single-coat paint for steel, zinc and aluminium surfaces, as well as a primer or a matt topcoat in epoxy systems exposed to weathering and/or chemical stress. Temadur 10 is a two-component matt polyurethane paint containing anti-corrosive pigments, hardener aliphatic isocyanate.

Huge colour range available with RAL, BS & NCS shades

MED-Approved Product

Accepted for painting surfaces inside of ships with MED (Marine Equipment Directive) certificate no VTT-C-11979-15-17. MED approved products can be used for painting of interior furniture and other surfaces on board ships.

Materials used for interior decoration on board cruise ships must fulfil the fire safety requirements of the UN agency IMO (International Maritime Organization). If the ship sails under an EU flag, the product must be MED approved in accordance with the EU Marine Equipment Directive. At the same time, the quality system of the supplying company is regularly audited by an exterior quality system auditor.

For paint products, this means that the product has been flame spread tested, and the toxicity of its smoke and combustion gases has been assessed. The products that have passed the test have a low flame spread and do not emit toxic smoke or combustion gases.

For more information, contact our technical team on 0113 2455450 (option 2) or send a message to [email protected]

For industrial and professional use only.

Quick Links - Click To Jump To Section:

• Features & Benefits
• Technical Data
• Surface Preparation
• Recommended Primers
• Recommended Topcoats
• Application Conditions
• Mixing Components
• Application
• Thinners
• Cleaners

Features & Benefits

• Huge colour range available with RAL, BS & NCS shades
• Can be used as a single-coat paint for steel, zinc and aluminium surfaces
• The paint is also used as a primer or a matt topcoat in epoxy systems exposed to weathering and/or chemical stress
• Provides an almost unlimited range of colours, including metallic effects
• The product has MED (Marine Equipment Directive) certificate no VTT-C-11979-15-17 and is thus accepted for painting surfaces inside ships
• Also recommended for (but limited to) painting:
• Haulage equipment
• Storage tank exteriors and other
• Steelwork
• Machinery and equipment

Technical Data

• Volume Solids: 56±2%. (ISO 3233)
• Weight Solids: 73±2%
• Specific Gravity: 1.4±0.1 kg / l (mixed)
• Pot Life (23℃): 4 hours
• VOC:
• The Volatile Organic Compounds amount is 430 g/litre of paint mixture.
• VOC content of the paint mixture (thinned 15% by volume) is 490 g/l.
• Mixing Ratio:
• Base: 7 parts by volume (Temadur 10)
• Hardener: 1 parts by volume (008 7590)

Recommended Film Thicknesses and Theoretical Coverage

Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.

Drying Times

Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.

Surface Preparation

Steel surfaces:

• Blast clean to grade Sa2½. (ISO 8501-1)
• If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Zinc surfaces:

• Sweep blast clean with mineral abrasives, e.g. quartz sand, to an even roughness. (SaS, SFS 5873)
• If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with Panssaripesu detergent.
• For hot dip galvanized surfaces see separate application instructions or contact Tikkurila Technical Service or Rawlins Technical on 0113 2455450 (option 2) or send a message to [email protected]

Aluminium surfaces:

• Sweep blast clean with non-metallic abrasives to an even roughness. (SaS, SFS 5873)
• If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with Maalipesu detergent.

Stainless steel:

• Roughen the surface by grinding or sweep blasting using non-metallic abrasives.

Primed surfaces:

• Oil, grease, salt and dirt are removed from the surface by appropriate means.
• Repair any damage to the primer coat.
• Note the overcoating time of primer. (ISO 12944-4)

Recommended Primers

• Temacoat GPL-S Primer
• Temacoat Primer
• Temacoat RM 40
• Temadur 10

Recommended Topcoats

• Temadur 10
• Temadur 20
• Temadur 50
• Temadur 90
• Temadur Clear
• Temathane 50
• Temathane 90
• Temathane PC 50
• Temathane PC 80

Application Conditions

• All surfaces must be clean, dry and free from contamination.
• The temperature of the ambient air, surface and paint should not fall below 5℃ during application and drying.
• Relative humidity of the air should not exceed 80% during application and drying.
• The surface temperature of steel should remain at least 3°C above the dew point.
• Good ventilation and sufficient air movement is required in confined areas during application and drying.

Mixing Components

• First stir base and hardener separately
• The correct proportions of base and hardener must be mixed thoroughly before use
• Use power mixer for mixing
• Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface and weaken the properties of the coating.

Application

• For airless spraying, the product is thinned depending on the temperature of the components and the required viscosity approximately 0–15%
• Mixing of the components and adjustment of the viscosity should be done right before use in order to reach an optimal result
• Recommended nozzle tip is 0.011"–0.015" and pressure 120–160 bar
• Spray angle shall be chosen according to the shape of the object
• For conventional spraying, the product is thinned approximately 5–15%
• Recommended nozzle tip is 1.6–1.8 mm and pressure 3–4 bar
• For brush application product should be thinned according to the circumstances

Thinners

• Thinner 1048
• Thinner 1061
• Thinner 1061 is also suitable for conventional spraying

Cleaners

• Thinner 1048 or Thinner 1061