Axalta ViterLac ABV Alkyd HB Gloss Finish is a one-component, modified alkyd, high gloss finish which has high build properties when applied by brush or spray. For use on agricultural and earth moving equipment and general steelwork.
Where a relatively fast drying high build gloss finish is required
Wide colour range of over 350+ RAL and BS shades
Fast drying minimises dust contamination to give a durable high gloss finish
Hard Dry in 4 hours at 23°C
For use as a finish coat over ViterPrime 035 and other alkyd primers
For application by airless spray with a high degree of sag resistance for spraying on difficult configurations
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cart
Axalta ViterLac ABV Alkyd HB Gloss Finish is a modified alkyd, high gloss finish which has high build properties when applied by brush or spray. For use on agricultural and earth moving equipment and it is ideal for structural steelwork.
Axalta ViterLac ABV Alkyd HB Gloss Finish has excellent sag resistance and is fast drying, minimising dust contamination to give a durable high gloss finish, and it is available in a wide range of colours.
Approvals/Certification - Please consult Axalta Coating Systems or Rawlins Paints Technical on 0113 2455450 (option 2) or send a message to [email protected].
High build properties when applied by brush or spray
For use on agricultural and earth moving equipment
Ideal for structural steelwork
Wide colour range of over 350+ RAL and BS shades
Excellent sag resistance
Hard Dry in 4hrs at 23°C
Should be applied over a suitable priming system
Product Specification
Technical Data
Axalta ViterLac ABV Alkyd HB Gloss Finish
Volume Solids
42 ± 2% (varies with colour)
VOC Content
481 + 20 g/litre (varies with colour)
SG
1.09 – 1.20 kg/lt (varies with colour)
Storage Conditions
Store in dry, cool conditions and protect from frost
Shelf Life
Minimum 12 months if stored as above in unopened containers
Flash Point
23-60°C
Film Thickness Range And Coverage
Product Data
Dry Film Thickness
Wet Film Thickness
Theoretical Coverage
Minimum
50 µm
119 µm
8.4 m2/litre
Maximum
80 µm
190 µm
5.2 m2/litre
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated
Drying Times
Product Data
Applied to 60 microns DFT
10℃
23℃
35℃
Dust Free
2 hr
1 hr
45 min
Hard Dry
8 hr
4 hr
3 hr
Overcoating
Minimum
24 hr
16 hr
10 hr
Maximum
Indefinite if clean and sound
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation
Surface Preparation
This product is a finish coat and should be applied over an appropriate primer and/or intermediate coat, please consult Axalta Coating Systems or Rawlins Paints Technical on 0113 2455450 (option 2) or send a message to [email protected] for advice
All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination
Mixing
Must be mixed thoroughly by using a mechanical agitator before use
Agitate periodically to ensure paint remains homogeneous
Only apply in conditions of good ventilation which must be maintained during drying and curing
Do not apply when rain, mist, sleet or snow are imminent
During application and drying time of the paint coating, the surface should be dry, the relative humidity should not exceed 85% and the steel temperature should remain at least 3°C above the dew point
Paint temperature should ideally be at a minimum of 15ºC
Application Methods
Airless Spray: Output fluid pressure at tip 1800-2500 psi min., Tip Size 11-19 thou (0.28-0.48 mm)
Application by brush will provide 50-60 microns dft
Avoid exceeding maximum dry film thickness or drying problems may result
Product Notes
Overcoating: this product is designed as finish coat. If overcoating, the compatibility of topcoats should be confirmed prior to application
Some shades may contain lead based colourants and these are labelled (L)
Not recommended for immersion
For best opacity use a primer or undercoat of a suitable shade
Health & Safety
Containers are provided with safety labels which should be observed
Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Product Details
5022-899201
Data sheet
Manufacturer
Axalta
Interior / Exterior Use
Exterior Use
For Use On
Steel
Application Method
Airless Spray, Brush
Sheen
Gloss
Colour
Fully Tintable
Single, Two or Three Pack
Single
Pack Size
5L
Minimum Applied Thickness
50 µm
Maximum Applied Thickness
80 µm
Touch Dry (at 20°C)
60 mins
Coverage
5.2m²/litre at 50 µm DFT, 8.4m²/litre at 50 µm DFT
Recommended Thinner/Cleaner
1050 Thinner/1006 Thinner
Min. Application Temperature
Steel temperature should remain at least 3°C above the dew point
Solids by Volume
42 ± 2% (varies with colour)
Shelf Life (from date of manufacture)
Minimum 12 months if stored as above in unopened containers
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Axalta ViterLac ABV Alkyd HB Gloss Finish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Axalta 1006 Thinner, for use with the Axalta range of coatings has a specially formulated blend of solvents designed to mix with its compatible paint/coating to create an optimal consistency for application whether it be for brush, roller or spray. Can also be used for the cleaning of some surfaces prior to application of the coating...
Axalta ViterPrime 035 Primer/Finish is a fast drying, high build alkyd zinc phosphate anticorrosive primer or primer/finish for structural steelwork.Designed for shop application by airless spray Can be used as an anticorrosive primer/finish or be overcoated with conventional or two-pack polyurethane topcoats such as ViterThane PLV...
We no longer stock this product, but can recommend Axalta TH400 Thinner as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450...
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...