Cromadex 442 One Pack Lower Odour Polyurethane Medium Texture Topcoat is a one pack lower odour topcoat that comes in a medium texture finish that adds value to your product. The product uses polyurethane technology providing excellent colour retention. The product has a long wet edge making it easier to apply to large items with no dry spray.
Rust-Oleum B95 High Build Flexible Epoxy
Rust-Oleum B95 High Build Flexible Epoxy is a two pack epoxy for hand cleaned, blasted, primed or galvanised steel, concrete and brickwork with outstanding corrosion, wear and impact resistance. Rust-Oleum B95 High Build Flexible Epoxy is an epoxy coating with the advantages of an elastic paint that moves with the structure to stop cracking or peeling.
Rust-Oleum B95 High Build Flexible Epoxy is based on two-component, modified low molecular epoxy resins and is practically solvent free. Designed for application on concrete, masonry, and hand tool prepared, blasted, primed or galvanized steel. Primarily intended for airless spray application but may also be applied by brush and roller.
Features & Benefits
- Flexible, high build epoxy for metal and concrete
- Excellent corrosion, wear and impact resistance
- Resistant against humidity and moisture
- Remains flexible to prevent cracking and peeling
- Virtually solvent free and low odour
- Twice as thick as regular epoxies (150μm dry)
Rust-Oleum B95 High Build Flexible Epoxy offers appropriate corrosion resistance in severe industrial and coastal exposures; high humidity and moisture conditions. Rust-Oleum B95 High Build Flexible Epoxy is, due to its flexibility, especially suitable for concrete and steel floors showing good abrasion and impact resistance; porous substrates should first be primed with Rust-Oleum 5401 Epoxy Impregnation Primer; very dense substrates, like ceramic tiles, should be primed with Rust-Oleum 3333 Super Adhesion Primer.
Rust-Oleum B95 High Build Flexible Epoxy can be applied directly on properly prepared steel or galvanized steel, on itself, on Rust-Oleum 9170 Epoxy Metal Primer, Rust-Oleum 9180 Epoxy Metal Primer or Rust-Oleum 9169 Epoxy Rust Primer. This product is also suitable for application on old, reversible coatings such as Chlorinated Rubbers, Vinyls, etc. If good U.V. and/or chemical resistance is required Rust-Oleum 9600 Rust-O-Thane Polyurethane should be applied.
Remove grease, oil and all other surface contamination by alkaline or high pressure (steam) cleaning in combination with appropriate detergents. Sand intact coatings to roughen the surface slightly. Check compatibility, especially when applied on reversible coatings, the application of a test-patch is strongly recommended. The surface must be clean and dry during application.
Concrete and masonry: New concrete or masonry should cure and dry for at least 30 days before applying the coating system. Remove laitance, any loose or unsound concrete or deteriorated coatings. Smooth concrete should be roughened. Remove curing compounds.
Steel: Remove loose rust, mill scale and deteriorated coatings by hand or power tool cleaning to St 2/3 (ISO 8501-01 : 1988). Large areas may be thorough blast-cleaned to Sa 2 (ISO 8501-01 : 1988), blast profile max. 50μm.
Directions for Use
Stir individual components thoroughly before mixing them together. Use the boxing method or use a low speed mixer.
- Mixing ratio: base (B95): activator (9501) = 1 : 1 by volume.
- Induction time: 15 minutes for a 10 litre. mix at 20°C.
- Pot-life: 45 minutes for a 10 litre. mix at 20°C.
- Dilution with at least 10% Thinner 160 extends pot-life 30 minutes.
Application & Thinning
- Brush: 10 to 15 vol.%; Rust-Oleum Thinner 160. Use natural bristles, long hair brushes.
- Roller: 10 to 15 vol.%; Rust-Oleum Thinner 160. Use medium nap polyamide (perlon 16-20mm.) rollers. Roller application requires 2 coats to achieve recommended d.f.t.
- Airless spray: 5 to 15 vol.%; Rust-Oleum Thinner 160. Pneumatic and electric airless equipment. Tip size: 0.015-0.025 inch. Fluid pressure: 250 - 300 bar.
Cleanup: Use Rust-Oleum Thinner 160. Preferably use disposable brushes and/or rollers.
Temperature of air, substrate and coating material between 10 and 35°C and relative humidity below 85%. The substrate temperature must be at least 3°C above dew point. Maximum dry film thickness per coat: 500μm dry, equals 505μm wet.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Be the first to ask a question about this product!
Nullifire PM018 Primer or Top Seal Epoxy Coating is a two-components modified epoxy coating. It is a heavy duty, high build coating for protection of steel in corrosive environments and is excellent for use at low temperatures.
Thermilate Trade Warmtouch Paint is a quick drying, semi-gloss paint which makes handrails and metal surfaces warm to the touch. It also reduces handrails becoming slippery due to precipitation and condensation and conforms to the Health and Safety Building Regulations 2000 law.
Cromadex 942 Medium Texture Stoving Topcoat is a stoving topcoat that comes in a medium texture finish that adds value to your article. The choice of stoving schedules enables production flexibility. The mar resistance of Cromadex 942 makes it suitable in tough environments. Available in a wide range of colours including BS, RAL and special matches all in...
Jotun Hardtop One is a one component moisture curing acrylic polysiloxane resin based coating. The product does not contain isocyanates, neither does it generate di-isocyanates during hotwork / welding or fire accidents. It has excellent gloss and colour retention. It is a high solids product. The product is fully recoatable at any stage of...
International Intergard 1735 is a high performance, low VOC, water borne two component epoxy with a high gloss finish. International Intergard 1735 is a tough, hard wearing chemically resistant epoxy finish suitable for most circumstances where the odour or emissions from solvent based coatings are unacceptable.
Nu-Steel TP Finish is the final coat of the Nu-Steel TP System, providing an excellent decorative appearance and outstanding resistance to solvents and chemicals, making it a first choice coating system for use on steelwork. Advantages Available in any RAL colour. Up to 15 years protection. 11m²/Litre approx. coverage. Touch-dry in 3 hours.
Cromadex 234 One Pack Air Drying Alkyd Fine Texture Topcoat is a one pack air drying topcoat that comes in a fine texture finish that adds value to your product. The product has a long wet edge that enables a seamless finish on large articles without dry spray. Available in the full Cromadex range of colours, including BS, RAL and special matches all in a...
Cromadex 642 Two Pack Polyurethane Medium Texture Topcoat is a two pack polyurethane medium texture topcoat with excellent exterior durability and chemical resistance. The product offers a medium texture appearance for an aesthetic finish. Demonstrates good mar resistance, ideal if the end product is to be widely handled. The addition of Rapidcure can...
This product is now only available with a minimum order of 800 litres; for smaller orders, we can recommend Jotun Hardtop CA as a great alternative. Jotun Jotaproof Topcoat is a two component cross linked acrylic coating. It has a glossy finish with very good gloss retention. It is a high solids, high build product. The product does not...
International Interfine 691 is a two pack, epoxy acrylic isocyanate free cosmetic finish providing good long term durability. International Interfine 691 offers equivalent performance to typical recoatable polyurethane cosmetic finishes.