Alternatively you can email our sales & support team on [email protected]
Blackfriar Metallic Paint
BF022
Blackfriar Metallic Paint is a bright metallic finish for decorating and gilding ornamental plasterwork, wood, metal railings, picture frames, models, fleur-de-lis, memorabilia & furniture.
Blackfriar Metallic Paint lets you get creative – enrich and gild interior and exterior surfaces. Ideal for ornamental plasterwork, picture frames, decorations, theatre props, furniture, radiators and textured wall finishes.
Preparation
Ensure surface to be coated is clean, dry, sound and free from wax, grease or any other contamination. Previously painted surfaces in sound condition should be abraded and degreased prior to application of Blackfriar Metallic Paint. Bare or new surfaces should be primed with the appropriate Blackfriar Primer.
Application
Stir thoroughly prior to use with a broad stirrer. The product may be applied by using a soft brush, short pile roller or spray. Apply the paint as evenly as possible to maintain an overall consistent finish. Like all metallic paints the most uniform finish is achieved by spraying. Application marks can be left in the film when brushing and rollering. Do not overwork the wet paint film when brushing or rollering.
Thinning
Maximum 10% water.
Limitations
Do not use under cold (less than 10°C), damp or humid conditions. Surfaces subject to high wear (eg. handrails) or high humidity (eg. kitchen or bathroom) can cause the metallic finish to prematurely tarnish. It is advisable under these conditions to overcoat the Metallic Paint with Blackfriar Quick Drying Clear Varnish.
Drying Time
Touch dry in 1 hour. Recoat after 4 hours. Drying times are based on an ambient temperature of 20°C and 50% relative humidity. Lower temperatures or higher humidity will prolong the drying and overcoating times.
Clean Up
Remove as much product as possible from application equipment before washing with water. Do not empty into drains or water courses. Some local authorities have special facilities for the disposal of waste coatings.
Storage
Store in a dry, safe place. Do not store in environments where extreme temperatures may occur. Keep within 5-30°C. Do not store in direct sunlight.
Features
Gilds surfaces
Decorative and ornamental
Interior and exterior use
Fast drying
Please contact Rawlins Paints' Technical Support Team on 0113 2455450for more information.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
I am looking for a paint suitable for the frame of my shower cubicle. This came up on google, and I wanted to check it is suitable? I understand I will need to buy and apply a primer also.
Answer:
It is not specifically designed for this application but if the areas to paint will not be in contact with water from the shower then it would be OK. If it is to be on areas directly wet by the shower then it wouldn't be a suitable product to use.
Melanie Harrison on 2017-04-15 21:58:01
Question: Can the metallic paint be used on my glass garden table. Can it be used on the metal frame.
Thank you
Answer:
Blackfriar Metallic Paint is suitable for exterior use and will be OK for this application. The table legs will need to be primed first following good preparation, assuming they are already coated with something a coat of Zinsser Bulls Eye 1-2-3 would be a good primer. If the legs are bare metal then a suitable metal primer can be applied before the Blackfriar Metallic Paint.
Blackfriar Quick Drying Varnish transforms your interior wooden surfaces. Available in a range of five natural shades, it provides a hardwearing, quick-drying finish.
For all types of interior wood
Tough and durable
Easy to clean water-based formulation
Apply via brush, roller or spray
Quick drying - touch dry in just 1 hour and...
Nu-Steel Cladding Paint is a modified acrylic paint specifically developed for application for use on aluminium cladding, pre-fab buildings and industrial environments. Also ideal for Plastisol and polyester coated steel.
Advantages
Acrylic paint solution
RAL shades. BS 4800 also available
Excellent resistance to UV
12-month shelf life...
SigmaCover 2, also known as Amerlock 2, a high-solids high performance self-priming low-VOC universal epoxy coating for substrates including carbon steel, concrete, masonry, galvanised steel, non-ferrous metal and stainless steel. The coating has numerous qualifications, including for nuclear service, flame spread, subsea surfaces and potable...
A durable and high performance acrylic coating for use where excellent weathering properties and chemical resistance are required. Use as a direct-to-metal acrylic coating for structural steel, as well as other exterior and interior uses.
Top Features
Smooth, attractive, high build finish
Excellent corrosion protection
Meets most VOC...
Eagle Aluminium Paint, a topcoat for bitumen coatings and substrates that provides protection against solar degradation and heat gain with a solar-reflective finish.
Dry in approx. 1 hour
For use on:
Bituminous coatings
Aged asphalt
Primed steel
Apply by brush or mohair roller
Requires just 2 coats
SigmaShield 2, previous known as Amerlock 2 GF, is a two-component, high solids glass flake reinforced polyamine cured epoxy coating that is suitable for immersion. Designed for long-term protection at areas subject to heavy wear and tear, with excellent abrasion, corrosion and impact resistance.
Low-temperature curing down to 0°C (32°F)...
Kem-Kromik 530 (formerly known as Sherwin-Williams C530 or as Leighs C530) is a high quality, quick drying, lead free single pack alkyd gloss finish for interior and exterior surfaces, ideally suited for equipment manufacturers and for structural steelwork. Kem-Kromik 530 possesses excellent gloss and colour retention and outstanding...
HMG Chlorinated Rubber is a versatile, high build, easy to apply, single pack Chlorinated Rubber based paint. It gives excellent durability combined with good resistance to acids, alkalis and oxidising agents in aqueous and gaseous forms.
Available in a wide colour range including RAL & BS shades.
Click to jump down to Technical...
Rust-Oleum 5500 Solvent Free Epoxy is a high build, solvent-free epoxy floor paint for garages, warehouses, showrooms, corridors, indoor car parks, workshops etc. Optimal protection in only one or two layers.
High build coating (150 microns), very durable
Suitable for frequent (chemical) cleaning
Excellent resistance against immersion...
A high solids and abrasion resistant coating which can be used as a primer, intermediate coat, or self-priming finish over steel or inorganic zinc primers. May be topcoated with itself, or a broad variety of high performance finish coats.
Top Features
Low odor and low VOC
Good chemical resistance
Used as a primer, intermediate, or finish...
Cromadex AQ40 One Pack Waterbased Air Drying Topcoat is a one pack water based air drying topcoat with excellent gloss and colour retention adding value to the finished article. Available in the full Cromadex range of colours and gloss levels, including BS, RAL and special matches all in a lead free finish. Life expectancy of up to 3 years in a C2...
Nu-Steel QD Finish is an economical decorative metal topcoat, for the protection of all types of metal, especially in projects which are time-critical. Conforms to BS 5493 - the code of practice for the protective coating of iron and steel against corrosion.
Advantages
Protects for up to 5 years
Dries quick
10m²/Litre coverage
12-month...
Cromadex 242 One Pack Fast Air Drying Alkyd Medium Texture Topcoat is a one pack fast air drying topcoat that comes in a medium texture finish that adds value to your article. It has excellent covering power to help reduce application costs. The product has a fast touch dry time enabling improved productivity.
Rust-Oleum 9200 Rust-O-Thane is a satin, water based polyurethane for a very durable and colourfast finish on coated floors, walls and primed metal. Especially recommended where general urethane performance like excellent weather resistance (UV), easy cleaning and abrasion resistance is required.
Rust-Oleum's hard wearing, washable...
Cromadex 400 One Pack Lower Odour Polyurethane Topcoat is a one pack lower odour topcoat using polyurethane technology providing excellent gloss and colour retention. The product is an automotive standard product with proven performance. The product has a long wet edge making it easier to apply to large items with no dry spray.
Thermilate Trade Warmtouch Paint is a quick drying, semi-gloss paint which makes handrails and metal surfaces warm to the touch. It also reduces handrails becoming slippery due to precipitation and condensation and conforms to the Health and Safety Building Regulations 2000 law.
Coverage Calculator
International Intersheen 579 is a fast drying, single component, modified acrylic finish intended for use as a sealer coat for single pack acrylic intumescent coating systems but may also be used as a cosmetic finish over single pack primers and intermediates.
Coverage Calculator
Rachel on 2019-08-16 18:26:47
