Teamac - Extra Brilliant Aluminium Paint
  • Teamac - Extra Brilliant Aluminium Paint
  • Teamac - Extra Brilliant Aluminium Paint
  • Teamac - Extra Brilliant Aluminium Paint
  • Teamac - Extra Brilliant Aluminium Paint

Teamac Extra Brilliant Aluminium Paint

505/A303/3/D

Teamac Extra Brilliant Aluminium Paint, is an all metal coating with thermal and photo reflective properties that can be used as a heat and light reflective protective finish on car wheels, hot water pipes, radiators, metal car components.  It provides heat resistance up to 150°C.

Advantages

Colour
Size
Finish
£21.37
VAT excluded

£25.64 Tax incl.
Quantity

Description

Teamac Extra Brilliant Aluminium Paint can be used as a heat and light reflective protective finish.  Teamac Extra Brilliant Aluminium Paint can also be used on car wheels, hot water pipes, radiators, metal car components and anywhere where a high metallic sheen is required on wood or metal surfaces.

Teamac Extra Brilliant Aluminium Paint contains a metallic aluminium which provides a silver finish and is heat resistant up to 150°C.



Click To Jump To Section:




Features & Benefits


Advantages



Product Specification


Technical Data
Volume Solids 42%
VOC Content 482 g/litre
SG 1.02°C
Viscostity 27 sec. B4 cup @ 25°C
Flash Point 38°C (closed cup)



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Maximum 20 - 25 μm 50 - 60 μm 15 - 20m2/litre @ 20 -25 microns D.F.T depending on surface porosity.



The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.



Drying Times


Drying Times At 20°C/RH 50%
Touch Dry: 3 Hours
Dry To Handle: 12 Hours
Dry To Recoat: 12 Hours or overnight
Fully Cured: 5 - 7 Days



Low temperature and high humidity will adversely affect application, drying and performance of any coating.



Surface Preparation


  • Ensure all surfaces are clean, dry and free from grease, oil and any other contaminates.
  • Bare steel should be free from dust, rust and scale.
  • Blast cleaning to SA 2½ is recommended. If blast cleaning is impractical, mechanical cleaning should be employed as hand cleaning does not clean the steel to the required degree.
  • Any oil or grease should be removed with solvent before de-rusting.
  • Where blast cleaning is carried out after assembly, special attention must be paid to edges, corners, nuts, bolts welds, etc.
  • Welds should, if necessary be ground and all weld spatter, slag etc. must be removed



Preceeding Coat


  • N/A



Mixing


  • Mix well before use.



Application Conditions


  • As dictated by normal good painting practice.  In confined spaces, provide adequate ventilation during application and drying.



Application Methods


Method Airless Spray Conventional Spray Brush Roller
  No No Yes Yes



  • Thinner (Max vol): N/A
  • Nozzle Size: 0.013"
  • Nozzle Pressure: 2000 psi (138 bar)
  • Cleaning Solvent: Thinners 14



Health & Safety


See safety data sheet - SDS 10663 in attachments section above.

Click to go back to the top of the page

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
505/A303/3/D

Data sheet

For Use On
Metal
Application Method
Brush, Spray
Sheen
Satin
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Pack Size
1L, 2.5L
Application
Brush, Spray
Dry to Handle (at 20°C)
12 Hours
Dry to Recoat (at 20°C)
12 hours or overnight
Fully Cured (at 20°C)
5 - 7 Days
Coverage
15-20m² per litre
Solids by Volume
42%
Touch Dry
3 Hours
Finish
High Metallic Sheen
Finish
High Metallic Sheen
Size
1 litre, 2.5 litre, 5 litre
Recommended Dry Film Thickness
20 - 25μm
Recommended Wet Film Thickness
50 - 60μm
UN Number
1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Teamac Thinner 14

A specially formulated blend of solvents designed to mix with its compatible Teamac or Coo-Var coating to create an optimal consistancy for application. Suitable for use with Brush, Roller or Spray. Teamac Thinner 14 can also be used for the cleaning of some surfaces prior to application of the coating. Also suitable for the cleaning of...

Price £13.54
In stock