2-pack acrylic finish in 6,700+ shades for solid colours and single-layer metallic finishes. Contains a thixotropic agent which gives a high sag resistance.
Suitable for use on Painted/Primed Surfaces for the coating of trailers, earthmoving, agricultural and construction equipment, and many other industrial painting applications
Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours
*Note: RAL Pearl colours shown are approximations only - matches will not be exact
Product can be purchased as a Two Component Pack, or as Base or Hardener only
High Build - Gloss Finish - Excellent durability and UV stability
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Selemix 7-130 2K Acrylic High Build Topcoat is a 2-pack Acrylic finish for solid colours and single-layer metallic finishes. Contains a thixotropic agent which gives a high sag resistance.
It is especially suitable for airless or air-assisted airless spray equipment but can also be applied by conventional or HVLP spray.
It is compatible with Selemix Epoxy and Polyurethane primers, giving a durable and hard-wearing paint system.
Selemix 7-130 has a gloss finish with excellent durability and UV stability.
It is suitable use on Painted/Primed Surfaces for the coating of trailers, earthmoving, agricultural and construction equipment, and many other industrial painting applications.
Suitable for use on Painted/Primed Surfaces for the coating of trailers, earthmoving, agricultural and construction equipment, and many other industrial painting applications
Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours
*Note: RAL Pearl colours shown are approximations only - matches will not be exact
Product can be purchased as a Two Component Pack, or as Base or Hardener only
High Build - Gloss Finish - Excellent durability and UV stability
Application by airless or air-assisted airless spray equipment, but can also be applied by conventional or HVLP spray
For Professional Use Only
Surface Preparation
Apply only on a clean and dry surface with a temperature above the dew point to avoid condensation. In confined spaces, provide adequate ventilation during application and drying.
Painted Surfaces, Polyurethane or Polyester Fillers:
Machine sand with P320-400 discs and degrease
Selemix Epoxy Primers or PU Primers:
Refer to Primer TDS for recoat time
Mixing
Thoroughly mix paint before activating and check colour before use
Please Note: Refer to the Product Data Sheet for detailed information regarding mixing ratios for the relevant binder/base and hardener/activator used.
Application Notes
Features
Conventional Spray
Airless Spray
Spraygun Setup:
Nozzle:
Gravity: 1.5-1.6mm
Suction: 1.8-2.0mm
Pressure feed: 1.0-1.4mm
Nozzle:
9-11 thou
0.23-0.28mm
Air Pressure:
HVLP: 2 Bar
Standard: 2-3 Bar
2-4 Bar
Fluid Pressure:
N/A
70-100 Bar
Number of coats:
2
2
Flash-off between coats:
5-10 mins
5-10 mins
Drying:
Air dry or bake at 60°C for 40-50 mins
Air dry or bake at 60°C for 40-50 mins
Flash-off before bake:
5-10 mins
5-10 mins
Wet Film Thickness:
220-225 microns
170-200 microns
Dry Film Thickness:
80-90 microns
80-100 microns
Please see the Product Data Sheet for detailed Application Instructions before use.
Theoretical Coverage
4.3-5.2 m²/L at 90 microns DFT
Note: Please see the Product Data Sheet for detailed information.
Drying Times
Drying Times 20°C
Dust Free
30 mins
Touch Free
1-2 hours
Tape Free
24 hours
Handleable
24 hours
Hard Dry
24 hours or after bake
Overcoating time
Minimum: when Hard Dry
Maximum: 24 hours by itself without sanding
Please Note: Lower temperature or film thickness higher than 100µm will extend drying times
Health & Safety
For comprehensive Health, Safety and Environmental advice, please refer to the relevant Material Safety Data Sheets and product can labels
THIS PRODUCT IS FOR PROFESSIONAL USE ONLY
Product Details
8926-935695
Data sheet
Manufacturer
Selemix
For Use By
Professional Use
Water / Solvent Based
Solvent Based
For Use On
Painted Surfaces
Sheen
Gloss
Single, Two or Three Pack
Two-Pack
Mixing Ratio
3 to 1
Application
Spray Airless Spray
Touch Dry (at 20°C)
2 hours
Pot Life (at 20°C)
2-3 Hours
Recommended Dry Film Thickness
80-100 microns
Recommended Wet Film Thickness
170-200 microns (depending on application method - see Data Sheet)
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Selemix 7-130 2K Acrylic High Build Topcoat is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
For use with selected products in the Selemix range including Selemix 2K Polyurethane Direct Topcoat.Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use OnlyMore Information Delivery Info
For use with selected products in the Selemix range including Selemix 7-110 2K Acrylic Topcoat.Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use OnlyMore Information Delivery Info