Fast-curing 2-pack epoxy finish with 6,700+ colour options for solid colours and single-layer metallic finishes. For steel surfaces primed with Selemix Epoxy Primers
Suitable for the coating of equipment and machinery, especially those in an aggressive environment
Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours
*Note: RAL Pearl colours shown are approximations only - matches will not be exact
Product can be purchased as a Two Component Pack, or as Base or Hardener only
Gloss finish that gives a hard, chemically resistant film
Selemix 7-410 2K Epoxy Topcoat (Fast Curing) is a 2-pack Epoxy finish for solid colours and single-layer metallic finishes. It has a gloss finish and gives a hard and chemically resistant film.
It is compatible with Selemix Epoxy Primers, giving a durable and hard wearing paint system.
Application can be by conventional or air-assisted airless spray.
It is suitable for the coating of equipment and machinery, especially those situated in an aggressive environment.
Please note: It should not be used on exterior surfaces exposed to sunlight if a good level of colour and gloss stability is required.
Please Note: Should not be used on exterior surfaces exposed to sunlight if a good level of colour and gloss stability is required
For Professional Use Only
Surface Preparation
Apply only on a clean and dry surface with a temperature above the dew point to avoid condensation. In confined spaces, provide adequate ventilation during application and drying.
Steel (use a primer in corrosive environments):
Machine sand with P80-120 discs and degrease
Selemix Epoxy Primers:
Refer to Primer TDS for recoat time
Mixing
Thoroughly mix paint before activating and check colour before use
Please Note: Refer to the Product Data Sheet for detailed information regarding mixing ratios for the relevant binder/base and hardener/activator used.
Application Notes
Features
Conventional Spray
Airless Spray
Spraygun Setup:
Nozzle:
Gravity: 1.3-1.4mm
Suction: 1.6-1.8mm
Pressure feed: 0.85-1.2mm
Nozzle:
9-11 thou
0.23-0.28mm
Air Pressure:
HVLP: 2 Bar
Standard: 2-3 Bar
2.5 Bar
Fluid Pressure:
N/A
80-100 Bar
Number of coats:
2
2
Flash-off between coats:
10-15 mins
10-15 mins
Drying:
Air dry or bake at 60°C for 60 mins
Air dry or bake at 60°C for 60 mins
Flash-off before bake:
10 mins
10 mins
Wet Film Thickness:
130 microns (2 x 75-100µm)
130 microns
Dry Film Thickness:
50 microns
50 microns
Please see the Product Data Sheet for detailed Application Instructions before use.
Theoretical Coverage
7.2-7.7m²/L at 50 microns DFT
Note: Please see the Product Data Sheet for detailed information.
Drying Times
Drying Times 20°C
Dust Free
30-40 mins
Touch Free
3-4 hours
Tape Free
12-18 hours
Handleable
6-8 hours
Hard Dry
12-18 hours or after bake
Overcoating time
Minimum: 3 hours
Maximum: 24 hours by itself without sanding
Please Note: Lower temperature or film thickness higher than 50µm will extend drying times
Health & Safety
For comprehensive Health, Safety and Environmental advice, please refer to the relevant Material Safety Data Sheets and product can labels
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Selemix 7-410 2K Epoxy Topcoat (Fast Curing) is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
2-pack Epoxy finish with 6,700+ colour options for solid colours and single-layer metallic finishes. Suitable for use on Steel surfaces primed with Selemix Epoxy PrimersSuitable for the coating of equipment and machinery, especially those in an aggressive environment Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC...
For use with selected products in the Selemix range including Selemix 7-410 2K Epoxy Topcoat. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use OnlyMore Information Delivery Info
For use with selected products in the Selemix range including Selemix 7-410 2K Epoxy Topcoat. Please see the Product Data Sheet for the Base Product for mixing ratios/application instructions before use For Professional Use OnlyMore Information Delivery Info