A 2K waterborne, acrylic topcoat, suitable for use on primed or painted surfaces exposed to weathering, mechanical and chemical stress, for both interior and exterior use. Available in High Gloss (8-110) and Matt (8-111). Fast Curing version availablehere.
Excellent gloss and colour retention and excellent hardness
Can be used over Selemix 2-pack solventborne or waterborne primers
Recommended for high quality finishes in industrial agricultural equipment and machinery
Product can be purchased as a Two Component Pack, or as Base or Hardener only
Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours
*Note: RAL Pearl colours shown are approximations only - matches will not be exact
For Professional Use Only
Please Note:Gloss levels are within +/- 10% depending on colour
Selemix 8-110/8-111 2K WB Acrylic Topcoat is a 2K waterborne, acrylic topcoat, suitable for use on primed or painted surfaces exposed to weathering, mechanical and chemical stress, for both interior and exterior use. Available in High Gloss (8-110) and Matt (8-111) - please choose from the drop down menu above. Fast Curing version availablehere.
It provides excellent gloss and colour retention and excellent hardness and can be used over Selemix 2-pack solventborne, or waterborne primers.
It is especially recommended for high quality finishes in industrial agricultural equipment and machinery.
Please note: Other gloss levels are achievable when 8-110 and 8-111 Binders are combined - please contact our Technical Department before placing an order on 0113 2455450 (option 2) or send a message to [email protected] for details.
Suitable for use on primed or painted surfaces exposed to weathering, mechanical and chemical stress, for both interior and exterior use
Available in High Gloss (8-110) and Matt (8-111).
Excellent gloss and colour retention and excellent hardness
Can be used over Selemix 2-pack solventborne or waterborne primers
Recommended for high quality finishes in industrial agricultural equipment and machinery
Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours
*Note: RAL Pearl colours shown are approximations only - matches will not be exact
For Professional Use Only
Surface Preparation
Apply only on a clean and dry surface with a temperature above the dew point to avoid condensation. In confined spaces, provide adequate ventilation during application and drying.
Any Selemix Solventborne or Waterborne 2K Primer:
Wet on Wet or Machine sand with P240-320 discs and degrease
Painted Surfaces:
Machine sand with P240-320 discs and degrease
Mixing
Thoroughly mix paint before activating and check colour before use
Features
Conventional Spray
Air Assisted Airless
By Weight:
8-110/8-111 Topcoat
9-110 Hardener
Water
By Weight:
1000
300
Thoroughly mix topcoat for 5 minutes and then add: 180 - 250 Water
By Weight:
1000
300
Thoroughly mix topcoat for 5 minutes and then add: 180 - 250 Water
By Volume:
8-110/8-111 Topcoat
9-110 Hardener
Water
By Volume:
3
1
Thoroughly mix topcoat for 5 minutes and then add: 0.5-0.75 (18-25%) Water
By Volume:
3
1
Thoroughly mix topcoat for 5 minutes and then add: 0.5-0.75 (18-25%) Water
Viscosity (at 20°C):
20-25 secs DIN4
20-25 secs DIN4
Pot Life (at 20°C):
3 hours
3 hours
Application Notes
Features
Conventional Spray
Air-Assisted Airless
Spraygun Setup:
Nozzle:
Gravity: 1.4-1.6mm
Suction: 1.6-1.8mm
Pressure feed: 0.8-1mm
Nozzle:
9 thou
0.23mm
Air Pressure:
HVLP: 2 Bar
Standard: 2-3 Bar
2.5-3.5 Bar
Fluid Pressure:
N/A
90-110 Bar
Number of coats:
1 Light closed + 1 medium
1 Light Dry + 1 Full
Flash-off between coats:
15-20 mins minimum at 20°C
2 mins minimum at 20°C
Drying:
60°C for 45 mins
Or 80°C for 20-25 mins
60°C for 45 mins
Or 80°C for 20-25 mins
Flash-off before bake:
45 mins minimum at 20°C
45 mins minimum at 20°C
Wet Film Thickness:
100-125 microns
100-125 microns
Dry Film Thickness:
40-50 microns
40-50 microns
Brush and Roller:
8-110/8-111Acrylic Topcoat can be applied by brush (solvent resistant) or roller short haired mohair roller:
Activate 3:1 with 9-110 Hardener
Thinning with 10% of water is recommended
Apply in 2 coats with minimum 45 minutes flash-off between coats
Please see the Product Data Sheet for detailed Application Instructions before use.
Theoretical Coverage
7 - 10 m² per litre at 50 microns DFT
Note: Please see the Product Data Sheet for detailed information.
Drying Times
Drying Times 20°C
Dust Free
20-25 mins
Touch Free
5-6 hours
Handleable
8-9 hours
Hard Dry
24-36 hours
Stoving
45-60 minutes @60°C (according to film thickness)
Overcoating time
Minimum: 8 hours
Maximum: 24 hours without sanding on clean surface with itself
Please Note: Lower temperature or film thickness higher than 50µm will extend drying times.
The drying times quoted are approximate times and will vary depending on drying conditions and film thickness.
Poor ventilation, temperature below 20°C, humidity above 85% RH and excessive film thickness will extend the drying times.
Health & Safety
For comprehensive Health, Safety and Environmental advice, please refer to the relevant Material Safety Data Sheets and product can labels
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Selemix 8-110/8-111 2K WB Acrylic Topcoat is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
A fast-curing 2K waterborne, acrylic topcoat, suitable for use on primed or painted surfaces exposed to weathering, mechanical and chemical stress, for both interior and exterior use. Available in High Gloss (8-110) and Matt (8-111). Standard Curing version available here.Excellent gloss and colour retention and excellent hardness Can be...
2K waterborne, acrylic coating, with 6,700+ colours for direct application to well-prepared steel, galvanized steel, phosphate steel, or aluminium surfaces exposed to weathering, mechanical and chemical stress, for both interior and exterior use. Available in High Gloss (8-110) and Matt (8-111). Fast Curing version available here.Excellent...