Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.
A waterborne matt enamel, one component topcoat in 6,700+ colours, based on an alkyd emulsion for internal and external use. Suitable for use with solventborne Selemix primers if completely dry, or suitably prepared Painted Surfaces.
Recommended as matt finish for agricultural machinery, haulage equipment and other machinery and equipment
Combines the safety and easy-to-apply characteristics of waterborne technology with the mechanical and chemical resistant properties of the solvent based synthetic enamels
Selemix 8-864 1K WB Synthetic Hydro-Thinnable Matt Topcoat is a waterborne matt enamel, one component topcoat, based on an alkyd emulsion for internal and external use. Suitable for use with solventborne Selemix primers if completely dry, or suitably prepared Painted Surfaces.
It is recommended as matt finish for agricultural machinery, haulage equipment and other machinery and equipment. It combines the safety and easy-to-apply characteristics of waterborne technology with the mechanical and chemical resistant properties of the solvent based synthetic enamels. It also gives flexibility and durability.
Please note: Other gloss levels are achievable when combined with 8-863 Gloss Binder (prior to tinting) to give semi-gloss and semi-matt finishes - please contact our Technical Department before placing an order on 0113 2455450 (option 2) or send a message to [email protected] for details.
For agricultural machinery, haulage equipment and other machinery and equipment
Available in over 6,700+ RAL, RAL Metallic*, BS, NCS and Selemix TIC colours
*Note: RAL Pearl colours shown are approximations only - matches will not be exact
For Professional Use Only
Surface Preparation
Apply only on a clean and dry surface with a temperature above the dew point to avoid condensation. In confined spaces, provide adequate ventilation during application and drying.
Selemix solventborne primers (if completely dry):
Wet on Wet or Machine sand with P320-360 discs and degrease
Painted Surfaces:
Machine sand with P320-360 discs and degrease
Mixing
Thoroughly mix paint before activating and check colour before use
Features
Conventional Spray
Air-Assisted Airless Spray
By Weight:
8-864 Topcoat
Water
By Weight:
1000
0
By Weight:
1000
0
By Volume:
8-864 Topcoat
Water
By Volume:
10
No thinning required
By Volume:
10
No thinning required
Viscosity (at 20°C):
As supplied
As supplied
Pot Life (at 20°C):
Unlimited
Unlimited
Application Notes
Features
Conventional Spray
Air-Assisted Airless Spray
Spraygun Setup:
Nozzle:
Gravity: 1.3-1.4mm
Suction: 1.6mm
Pressure feed: 0.8-1.0mm
Nozzle:
9-11 thou
0.23-0.28mm
Air Pressure:
HVLP: 2 Bar
Standard: 2-3 Bar
2-3 Bar
Fluid Pressure:
N/A
70-100 Bar
Number of coats:
2 medium coats
2 medium coats
Flash-off between coats:
10-25 mins minimum at 20°C or until matt
10-25 mins minimum at 20°C or until matt
Drying:
Air dry
Air dry
Wet Film Thickness:
100-125 microns
100-125 microns
Dry Film Thickness:
40-50 microns
40-50 microns
Please see the Product Data Sheet for detailed Application Instructions before use.
Theoretical Coverage
5.7 - 6.8 m² per litre at 50 microns DFT
Note: Please see the Product Data Sheet for detailed information.
Drying Times
Drying Times 20°C
Dust Free
10-15 min
Touch Free
4-5 hours
Handleable
24 hours
Hard Dry
48 hours
Overcoating time
Minimum: 24 hours
Maximum: 7 days without sanding on clean surface with itself
Please Note: Lower temperature or film thickness higher than 50µm will extend drying times.
The drying times quoted are approximate times and will vary depending on drying conditions and film thickness.
Poor ventilation, temperature below 20°C, humidity above 85% RH and excessive film thickness will extend the drying times
Health & Safety
For comprehensive Health, Safety and Environmental advice, please refer to the relevant Material Safety Data Sheets and product can labels
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Selemix 8-864 1K WB Synthetic Hydro-Thinnable Matt Topcoat is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
A one-component gloss topcoat with 6,700+ colour options, based on high solids resins, which is water thinnable, providing a low VOC topcoat for internal and external use. Suitable for use with solventborne Selemix primers if completely dry, or suitably prepared Painted Surfaces.Recommended as gloss finish for agricultural machinery,...