HMG C71 Speedline is a high quality, single pack, synthetic alkyd enamel suitable for brushing or spraying. Offers fast surface drying, good through drying (even in thick films), and a hard, tough finish, with minimal yellowing even at high temperature - ideal for machinery, appliance and agricultural projects.
For use on ferrous and suitably prepared non-ferrous metals
Can be used as part of a finishing system for more demanding exposure scenarios - minimal yellowing
Professional use only
Manufactured under the auspices of an ISO 9001 management system
and lightly abraded prior to application of suitable HMG Primer
Aluminium to be degreased using:
HMG Prep Clean 2802 Degreaser
HMG Prep Clean 2803 Degreaser
or HMG Prep Clean 2804 Degreaser
abrade with P180 – P320, prior to application of suitable HMG Etch Primer and suitable HMG Primer
Mild Steel remove millscale and thoroughly degrease using:
HMG Prep Clean 2802 Degreaser
HMG Prep Clean 2803 Degreaser
or HMG Prep Clean 2804 Degreaser
abrade with P80 – P180 if necessary, before applying suitable HMG Primer
Shot Blasted Steel remove all traces of blast grit/sand before applying suitable HMG Primer
Previously painted/General Maintenance:
High pressure wash to remove all loose debris and poorly adhered existing coatings to remove salts and other contaminants
Degrease using suitable HMG Prep Clean 2800 to remove grease and oils not removed with pressure washing alone
Remove all loose and failed coatings back to firm, wire brush to remove rust and corrosion to clean metallic appearance
All edges to be firm and well feathered
Abrade to promote good adhesion
Wipe over with degreaser to remove loose debris from abrasion
Substrate to be clean, free of grease, oils, dust and completely dry prior to application
Application
Read and follow Safety Data Sheet, Product Information Sheet, and label instructions
Stir paint thoroughly before use
Always use the same batch number on the same job
Check colour and sheen, HMG will not accept any discrepancies arising after use
Filter the product immediately before use
Reduce emissions and maintain quality by replacing tin lid after use
Substrates:
C71 Speedline is suitable for use on all properly cleaned and prepared bare ferrous and non-ferrous metals and most previously coated metals
Previous coatings should be fully cured and prepared, test patch is recommended to check compatibility
Previously painted timber should be dry with all coatings sound and fully adhered
Failed previous coatings should be removed back to firm well feathered edge
Suitable primer is recommended for use over aluminium and new galvanised metals
Rusted steel to be suitably prepared and anti-corrosive primer applied prior to C71
Not for application over chlorinated rubber or bitumen coatings
Application Climate:
Substrate temperature should be 5⁰C or above for application and during cure, and a minimum of 3⁰C above the dew point
Adequate dry air ventilation should be supplied during drying
Application Information:
Thinning should only take place after material is thoroughly mixed
Application and use should always conform with the codes of practice described in BS 6150 and BS 5493
Surface Preparation:
Ensure surfaces are clean, dry and free from grease, oils, dust and other contamination prior to application
Thoroughly degrease using suitable HMG degreaser and where applicable, abrade to remove rust and promote good adhesion
For best results and optimum corrosion protection mild steel should be blast cleaned to Sa2.5
If in doubt, please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Resistance
Health & Safety
Refer to the Safety Data Sheet in the 'Data Sheets' section above, as well as tin label prior to use
Suitable respiratory equipment should be worn when spraying
Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with water and disposed of in a noncombustible container with a tight fitting lid
Product Details
4359-853526
Data sheet
Manufacturer
HMG Paints Limited
For Use By
Professional Use
Interior / Exterior Use
Interior & Exterior
For Use On
Bare Ferrous metals Bare Non-Ferrous metals Fencing Gates Iron Timber Agricultural Machinery Construction Machinery Vehicles
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG C71 Speedline is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
HMG Synthetic BDX Primer is a high build, anti-corrosive, single pack alkyd primer for use under all HMG synthetic topcoats, combining high build and excellent sandability with outstanding application and scratch filling properties.For use on suitably prepared structural steel, chassis, fabrication and aluminium Can be applied to bare...
HMG Synthetic High Opacity Undercoat is a 1K alkyd/polyurethane undercoat with superior brushing qualities and excellent obliteration properties.Suitable for large areas due to its ease of application and long wet edge time Please note: Colours shown are for illustrative purposes onlyMore Information Delivery Info
HMG Hardener 9029 ZIP is an isocyanate hardener.Designed for use in recommended HMG Alkyd and Polyurethane Alkyd systems. Upgrades the performance characterstics of the system, including durability and time to touch dry may decrease by 10 - 20% dependant on paint system, film thickness and curing conditions.More Information Delivery...
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...