Tor Farm Oxide Semi-Gloss is a general purpose finish with low toxicity, for use on and around farms and in farm buildings on a variety of substrates, including bare wood, steel and masonry.
Modified alkyd resin binder pigmented with low toxicity pigments and extenders, thinned with low aromatic white spirit. Contains no lead pigments
Surface preparation required - refer further below for more details
For brush or roller application
Can be applied by conventional spray if thinned with Tor TH10
Tor Farm Oxide Semi-Gloss, a general purpose finish with low toxicity, for use on and around farms and in farm buildings on a variety of substrates, including bare wood, steel and masonry.
The semi-gloss finish can be applied by brush or roller, or can be thinned for use with a conventional sprayer.
Refer below for details on surface preparation and application.
Features & Benefits
Semi-gloss general purpose finish
Ideal for farm buildings
For use on a variety of bare substrates, including:
Wood
Masonry
Steel
For brush or roller application
Can be applied by conventional spray if thinned with Tor TH10
Refer below for application details
Low-toxicity
Ensure good ventilation during application and drying
Good coverage - up to 12 square metres per litre
Touch dry in 4-5 hours - overcoat after 16 hours
Product Information
Modified alkyd resin binder pigmented with low toxicity pigments and extenders, thinned with low aromatic white spirit. Contains no lead pigments.
Product reference
AK789
Volume solids
54%
Typical thickness
45 microns dft form 83 microns wet
Theoretical coverage
12 square metres per litre
Practical coverage
10 square metres per litre
VOC content
EU limit value for this product (cat A/d): 300 g/l. This product contains max 300 g/l VOC
Surface Preparation
Bare Wood:
Thoroughly sand, wipe clean with Tor TH10 and prime with AK610 Tor Aluminium Wood Primer followed when dry by one coat of Farm Oxide.
Bare Steel:
Chip, scrape and wire brush to ST2 Swedish Standard and prime with Farm Oxide or AK618 Tor QD Red Oxide Primer followed when dry by one coat of Farm Oxide.
Bare Masonry:
Should be dry and free from any loose and flaking or powdery material, oil or grease. Stabilise by applying one coat of AK602 Tor SP Stabilising Sealer followed when dry by one coat of Farm Oxide.
Application Details
Mix ratio
N/A
Method of application
Brush or short pile roller. By reducing with 15-20% Tor TH5 or TH10 can also be applied by conventional spray.
Cleaner
Tor TH5 for cleaning equipment
Pot Life
N/A
Drying Times
Substrate Temperature
Touch Dry
Hard Dry
Overcoating Interval
Minimum
Maximum
20°C
4 -5 hours
16 hours
16 hours
28 days
Note: Drying/curing times will be shortened by higher temperatures and lengthened by lower temperatures
Storage and Handling
Store in a safe place out of the reach of children
Flash point
Above 32°C
Shelf life
2 years in unopened containers
Limitations
Ensure good ventilation during application and drying.
Avoid skin and eye contact i.e. wear gloves, goggles, etc
Ensure good ventilation, mechanical if necessary
Store and use away from heat and flame
Do not eat or smoke in the vicinity of work
Wash hands before eating
Refer to supply container for additional warning labels
Product Details
4112-518436
Data sheet
Manufacturer
Tor Coatings
For Use By
Professional Use
Water / Solvent Based
Solvent
For Use On
Wood, Steel, Masonry
Application Method
Brush, Roller
Sheen
Semi-Gloss
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Pack Size
2.5L, 5L, 20L
Parts
1
Solvent
Modified alkyd resin binder pigmented with low toxicity pigments and extenders, thinned with low aromatic white spirit contains no lead pigments.
Mixing Ratio
-
Suitable Substrates
Bare wood, steel, masonry
Key Features
Semi-gloss finish for farm buildings
Touch Dry (at 20°C)
4 -5 hours
Dry to Handle (at 20°C)
-
Dry to Recoat (at 20°C)
16 hours
Fully Cured (at 20°C)
16 hours
Pot Life (at 20°C)
-
Coverage
12 square metres per litre
Recommended Thinner/Cleaner
Tor TH5 or TH10
Unit Contents
-
Compatible Primers
AK610 Tor Aluminium Wood Primer, AK602 Tor SP Stabilising Sealer
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Tor Farm Oxide Semi-Gloss is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Tor General Purpose Thinner (TH10) - also known as Tor Tortread SP Thinners - is to be used for the thinning (where necessary) of general purpose primers, undercoats and finishes or for cleaning the same materials from brushes, rollers and trays immediately after application.
More Information Delivery Info
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3).
Please click here for important information about these kits.
Kit Contents:
SET 1 (Hand Tools)
1 x Rust-Oleum...
