Single pack vinyl acrylic in 5,000 colours for direct application to many difficult to coat substrates including hard plastics, powder coatings, most factory finishes and architectural cladding.
Also suitable for flexible substrates, PVC curtain material, uPVC, plastisol, cladding coatings and fibreglass*
*for areas incorporating draught seals and gaskets, HMG PVC PRO is the preferred product
Exceptional flexibility and adhesion
Quick drying - touch dry in 15 mins, re-coat in 1 hour
Thinner: HMG 2661 - for application in temperatures in excess of 25⁰C, Thinner 2604 slow thinner may be used to increase wet edge time
Full BS, RAL, agricultural and commercial vehicle colour ranges, including metallic finishes
Available in 5,000+ colours from RAL, NCS, and British Standard
Substrates
HMG PVC17 for application to most suitably prepared hard plastics, PVCu, powder coated, and other factory finished cladding, PVC curtains and many other plastic substrates
New curtains and other flexible substrates will require airing for at least 7 days prior to coating, ensuring any trapped plasticisers can escape, failure may result in poor adhesion and premature failure of coatings
Not suitable for coating areas incorporating draught seals and gaskets or over bitumen or chlorinated rubber coatings
Application Climate
Substrate temperature should be 5⁰C or above for application and during cure, and a minimum of 3⁰C above the dew point
Adequate dry air ventilation should be supplied during drying
Application Information
Thinning should only take place after material is thoroughly mixed
Application and use should always conform with the codes of practice described in BS 6150 and BS 5493
Surface Preparation
Ensure surfaces are clean, dry and free from grease, oils, dust and other contamination prior to application
Thoroughly clean and degrease using suitable HMG Prep Clean 2805 for new or HMG 2806 for old or aged substrates
General Specification
Clean to remove all loose debris and other contamination
Thoroughly clean and degrease using suitable HMG Prep Clean – 2805 for use on new substrates, 2806 for old or aged
Apply by cloth and quickly remove using clean lint free cloth
Repeat until surface is clean and free from all deposits (grease, oil, silicone)
Replace cloths regularly to ensure that contamination is not re-applied to the surface
Lightly abrade using Scotch-Brite pad to provide key, wipe with lint free cloth to remove loose dust prior to application
Painting existing coatings (powder coated)
Always check compatibility of new and old coatings prior to full application
Check all existing coatings are well adhered with all loose and failed material removed back to firm with all edges well feathered
Degrease using suitable HMG Prep Clean
Remove any rust back to clean metallic appearance, spot prime with suitable HMG Primer or HMG Ferrozinc Rust Convertor
Lightly abrade existing coatings to provide key, wipe with lint free cloth to remove loose dust
Application
A light dusting should then be sprayed on to the plastic to check that all contaminants have been removed
Apply 2 coats via brush or compliant spray gun to give full and even coverage
Allow a flash off time of 10-15 mins between coats
Film build should not exceed 35 microns DFT
The product will be touch dry in around 10-15 mins, hard dry after 45-60 minutes depending on ambient atmosphere
Windows and doors should be left open as long as possible, to allow the coating to fully cure
HMG recommend PVC Pro for painting uPVC windows and doors
For further assistance please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information
Health And Safety
Refer to Safety data sheet (see section above) and tin label prior to use
Suitable respiratory equipment should be worn when spraying
Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with water or disposed of in a non-combustible container with tight fitting lid
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG PVC17 Colours is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
HMG Synthetic BDX Primer is a high build, anti-corrosive, single pack alkyd primer for use under all HMG synthetic topcoats, combining high build and excellent sandability with outstanding application and scratch filling properties.For use on suitably prepared structural steel, chassis, fabrication and aluminium Can be applied to bare...
HMG Ferrozinc Rust Converter is a high performance water-based rust converter, ideal for application to areas difficult to shot-blast or where total removal of rust is not possible. Also suitable for surfaces difficult to dry due to existing moisture.Easily applied single pack material Changes colour to show rust has been neutralised...
HMG Prep Clean 2805 is a medium strength, anti static preparatory cleaning solvent.Suitable for degreasing of new u-PVC and other plastic substratesMore Information Delivery Info
Vinyl Acrylic Aerosol with 5,000 colours - exceptional flexibility and adhesion for direct application to many difficult to coat substrates including hard plastics, powder coatings, most factory finishes and architectural cladding.400ml/16oz Aerosol Available in packs of 1 or packs of 6+, 50 and 100 with discounted price breaks Also...