HMG SQ26 Crackle Base Coat

    TOPCRACKLEBASE
    HMG4374

    HMG SQ26 Crackle Base Coat is an air dried special effect finish, originally developed for ultra high quality interior decorative domestic and industrial applications.

    This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:

    3-Pack System Details
    Base (Part 1)HMG SQ26 Crackle Base Coat
    Top Coat (Part 2)HMG SQ26 Crackle Top Coat
    Thinner (Part 3)HMG SQ26 Crackle Coat Thinner 2738

    • Part one of a three-pack system
    • Available in 5,000+ colours from RAL, NCS, and British Standard

    Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

    Product customisation

    Don't forget to save your customization to be able to add to cart
    • 250 char. max
    Colour Group
    Size
    Finish
    £48.58(ex. VAT)
    £58.30 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    HMG SQ26 Crackle Base Coat is an air dried special effect finish, originally developed for ultra high quality interior decorative domestic and industrial applications.

    Please note this product is one part of a three-pack system which MUST be purchased/used together with HMG SQ26 Crackle Top Coat and HMG SQ26 Crackle Coat Thinner 2738

    For application on the tough, flexible and adherent SQ26 Top Coat, which can be applied over all suitably primed substrates.



    Click To Jump To Section:




    Features & Benefits


    • Available in 5,000+ colours from RAL, NCS, and British Standard



    Product Specification


    Technical Data
    Volume Solids:45.8%
    VOC Content:0.700kgs/ltr
    SG:-
    Viscosity:200 mPas
    Density:1.025 g/cm³
    Storage Conditions:Store between 5°C - 25°C. When not in use, cans must be kept sealed.
    Shelf Life:12 months from delivery date in original sealed containers.
    Flash Point:-4°C



    Film Thickness Range And Coverage


    Product Data
     Dry Film ThicknessWet Film Thickness
    Compliant Spray:20 μm50 μm



    Coverage: 10 square metres per litre @ 20 microns dft (Theoretical).

    • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
    • These values are a guide only and are not to be used as specifications.
    • Film thickness will vary depending on actual use and specification.
    • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



    Drying Times


    Drying Times At 20°C
    Touch Dry:10 minutes
    Fully Cured:45 minutes



    Surface Preparation


    • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
    • Thin SQ Basecoat 1:1 with 2738 Thinners. Apply 2 full coats of HMG SQ26 Basecoat over suitably primed substrate.

    Application Methods


    Technical Data
    Compliant Spray Gun
    Mixing Ratio:Base: 1
    Thinner: 1
    Thinner Options:Thinner 2738
    -
    Viscosity:30 - 35 seconds B4 cup
    Spray Gun Setup:1.4 - 1.8
    Number Of Coats (Guide Only):1 full coat
    Flash Off:-



    • The tough, flexible and adherent SQ 26 Basecoat can be applied over all suitably primed substrates. This is followed (after the basecoat has dried) by a full coat of the unique HMG SQ 26 crackle coat.
    • During drying, a shrinkage effect on the specially formulated crackle coat leads to a unique decorative "Crackle finish" which is available in range of colours.
    • Finally a clear over-lacquer is used to seal and preserve the unique "crackle" decorative effect.



    For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]

    Product Notes


    Information on basic physical and chemical properties
    Form:Liquid
    Colour:According to product specification
    Odour:Characteristic
    Odour Threshold:Not determined
    pH-value:Not determined
    Change in Condition
    Melting point/freezing point:Undetermined
    Initial boiling point and boiling range:82°C
    Flash Point:4°C
    Flammability (solid, gas):Not applicable
    Ignition temperature:270°C
    Decomposition temperature:Not determined.
    Auto-ignition temperature:Product is not selfigniting
    Explosive properties:"Product is not explosive. However, formation of explosive air vapour mixtures are possible."
    Explosion limits: Lower:1.1 Vol %
    Explosion limits: Upper:1.7 Vol %
    Vapour pressure at 20°C:29 hPa
    Density at 20°C:1.015 g/cm³
    Relative density:Not determined
    Vapour density:Not determined
    Evaporation rate:Not determined
    Solubility in / Miscibility with water:NOT MISCIBLE
    Partition coefficient: n-octanol/water:Not determined
    Viscosity: Dynamic at 20°C:200 mPas
    Viscosity: Kinematic:Not determined
    Solvent content: Organic solvents:59.0%
    Solids content:44.7%



    Health & Safety


    • Refer to the safety data sheet in the attachments section above and tin label prior to use.
    • Suitable respiratory equipment should be worn when spraying.

    Click to go back to the top of the page

    Product Details
    4374-833279

    Data sheet

    Manufacturer
    HMG Paints Limited
    Interior / Exterior Use
    Interior Use
    Application Method
    Spray
    Sheen
    Matt
    Colour
    Fully Tintable
    Single, Two or Three Pack
    Single
    Pack Size
    1L
    2.5L
    5L
    Mixing Ratio
    Base: 1 - Thinner: 1
    Touch Dry (at 20°C)
    10 Minutes
    Fully Cured (at 20°C)
    45 Minutes
    Coverage
    10 square metres per litre @ 20 microns dft (Theoretical)
    Recommended Thinner/Cleaner
    Thinner 2738
    Density
    1.025 g/cm³
    Solids by Volume
    45.8 %
    Heat Resistance (up-to)
    80°C
    VOC
    0.700kgs/ltr
    Shelf Life (from date of manufacture)
    12 months from delivery date in original sealed containers.
    Size
    1L and 5L
    Recommended Dry Film Thickness
    20 μm
    Recommended Wet Film Thickness
    50 μm
    UN Number
    UN1263
    Finish
    Matt
    Finish
    Matt
    Application Method
    Spray
    Product Usage Type
    Basecoat
    Colour Family
    White
    Colour Family
    Red
    Colour Family
    Metallic
    Colour Family
    Pink
    Colour Family
    Anthracite Grey
    Colour Family
    Purple
    Colour Family
    Grey
    Colour Family
    Black
    Colour Family
    Blue
    Colour Family
    Neutral
    Colour Family
    Brown
    Colour Family
    Stone
    Colour Family
    Orange
    Colour Family
    Beige
    Colour Family
    Yellow
    Colour Family
    Green
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    HMG SQ26 Crackle Base Coat is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    HMG SQ26 Crackle Top Coat

    HMG SQ26 Crackle Top Coat is an air dried special effect finish, originally developed for ultra high quality interior decorative domestic and industrial applications. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:3-Pack System DetailsBase (Part 1) HMG SQ26 Crackle...

    Price £72.64 (ex. VAT)
    In Stock and Available for Delivery

    HMG SQ26 Crackle Coat Thinner 2738

    HMG SQ26 Crackle Coat Thinner 2738G is thinner designed specifically for use with the HMG SQ26 Crackle Coat system. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:3-Pack System DetailsBase (Part 1) HMG SQ26 Crackle Base CoatTop Coat (Part 2) HMG SQ26 Crackle...

    Price £38.22 (ex. VAT)
    In Stock and Available for Delivery