HMG Thinner 2671
HMG Thinner 2671 is an alcohol based thinner.For use in recommended HMG systems.More Information Delivery Info
£14.05 (incl. VAT)
£11.71 (ex. VAT)
HMG Uniblok Sealer is a 1K air drying sealer / isolator for sealing synthetic enamels against attack when overcoating with stronger solvent systems such as cellulose, 2K finishes etc.
HMG Uniblok Sealer is a 1K air drying sealer / isolator for sealing synthetic enamels against attack when overcoating with stronger solvent systems such as cellulose, 2K finishes etc.
Technical Data | ||||||
---|---|---|---|---|---|---|
HMG Uniblok Sealer | ||||||
Volume Solids: | 67.6% | |||||
VOC Content: | 0.635kgs/ltr | |||||
SG: | - | |||||
Viscosity: | 280 mPas | |||||
Density: | 1.407 g/cm³ | |||||
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | |||||
Shelf Life: | 12 months from delivery date in original sealed containers. | |||||
Pot Life: | - | |||||
Flash Point: | 13°C |
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Pressure Pot: | 25 μm | 60 μm | |
Compliant Spray Gun: | n/a | n/a | |
Brush: | n/a | n/a | |
Roller: | n/a | n/a |
Coverage: 15 square metres per litre @ 25 microns dft (Theoretical)
Drying Times At 20°C | |
---|---|
Touch Dry: | 20 minutes |
Dry To Recoat: | Possible after 1 hour. Do not abrade Uniblok prior to overcoating. |
Fully Cured: | 1 hour |
Technical Data | |||||
---|---|---|---|---|---|
Pressure Pot | Compliant Spray Gun | Brush | Roller | ||
Mixing Ratio: | Ready for use | Base: 1 | Base: 1 | Base: 1 | |
- | Thinner: 1 | Thinner: <20% | Thinner: <20% | ||
Thinner Options: | - | Thinner 2671 | Thinner 2671 | Thinner 2671 | |
Viscosity: | - | 20 - 25 seconds B4 cup | - | - | |
Spray Gun Setup: | - | 1.4 - 1.8 | - | - | |
Number Of Coats (Guide Only): | 1 full coat | 1 full coat | 1 full coat | 1 full coat | |
Flash Off: | - | - | - | - |
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Information On Basic Physical And Chemical Properties | ||||||
---|---|---|---|---|---|---|
HMG Uniblok Sealer | ||||||
Form: | According to product specification | |||||
Colour: | According to product specification | |||||
Odour: | Characteristic | |||||
Odour Threshold: | Not determined | |||||
pH-value 20°C: | Not determined | |||||
Melting point/freezing point: | Undetermined | |||||
Initial boiling point and boiling range: | 78°C | |||||
Flash Point: | 13°C | |||||
Flammability (solid, gas): | Not applicable | |||||
Ignition temperature: | 300°C | |||||
Decomposition temperature: | Not determined | |||||
Auto-ignition temperature: | Product is not selfigniting. | |||||
Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | |||||
Explosion limits: Lower: | 2 Vol % | |||||
Explosion limits: Upper: | 15 Vol % | |||||
Vapour pressure at 20°C: | 59 hPa | |||||
Density at 20°C: | 1.407 g/cm³ | |||||
Relative density: | Not determined | |||||
Vapour density: | Not determined | |||||
Evaporation rate: | Not determined | |||||
Solubility in / Miscibility with water: | NOT MISCIBLE | |||||
Partition coefficient: n-octanol/water: | Not determined | |||||
Viscosity: Dynamic at 20°C: | 280 mPas | |||||
Viscosity: Kinematic: | Not determined | |||||
Solvent content: Organic solvents: | 32.2% - Water 0.2% | |||||
Solids content: | 67.6% |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG Uniblok Sealer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Thinner 2671 is an alcohol based thinner.For use in recommended HMG systems.More Information Delivery Info
£14.05 (incl. VAT)
£11.71 (ex. VAT)
HMG Uniblok Sealer Aerosol is a 1K air drying sealer / isolator for sealing synthetic enamels against attack when overcoating with stronger solvent systems such as cellulose, 2K finishes etc. For the non-aerosol version of this product please see HMG Uniblok Sealer.400ml/16oz Aerosol Outstanding sealing properties Suitable for a wide...
£26.92 (incl. VAT)
£22.43 (ex. VAT)