Blackfriar Red Oxide Metal Primer is an anti-corrosive, red oxide primer for the protection of ferrous metals. Specifically formulated for painting ferrous surfaces such as iron and steel to prevent rust forming. Contains zinc phosphate. Product Features Anti-corrosive. Prevents rust. For ferrous metals such as iron and steel. Interior...
Blackfriar Acrylic Primer Undercoat
Blackfriar Acrylic Primer Undercoat is an all-in-one, quick drying primer and undercoat for use on a wide range of substrates including wood, masonry, dry plaster and cement. Provides excellent opacity and adhesion.
- Quick drying.
- Interior and exterior use.
- All-in-one primer and undercoat.
- Excellent opacity.
- Excellent adhesion.
Blackfriar Acrylic Primer Undercoat is ideal for use inside and out. It dries quickly, so you can apply a second coat of Blackfriar Acrylic Primer Undercoat, enabling you to finish a whole job in one day. It is suitable for bare woodwork, hardboard, masonry, dry plaster and cement.
Ensure surface to be coated is clean, dry, sound and free from wax, grease or any other contamination. Treat knots and resinous areas with Blackfriar Patent Knotting and allow to dry before applying Blackfriar Acrylic Primer Undercoat. Exposed ferrous metal (e.g. nails) should be spot primed with the appropriate Blackfriar Metal Primer.
Stir thoroughly prior to use with a broad stirrer. The product may be applied by brush, roller or spray. Two coats are recommended to give best protection. On open end grain timber brush in well and apply two coats. For porous surfaces or if applying by spray the product may be thinned up to 10% with water.
Maximum 10% water.
Touch dry in 1 - 2 hours. Recoat after 4 hours and within 3 days. Drying times are based on an ambient temperature of 20°C and 50% relative humidity. Lower temperatures or higher humidity will prolong the drying and overcoating times.
Remove as much product as possible from application equipment before washing with water. Do not empty into drains or water courses. Some local authorities have special facilities for the disposal of waste coatings.
Store in a dry, safe place. Do not store in environments where extreme temperatures may occur. Keep within 5-30°C. Do not store in direct sunlight.
Features & Benefits
- All-in-one primer and undercoat
- Quick drying
- Excellent opacity
- Excellent adhesion
- Interior and exterior use
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Blackfriar Professional
- Water / Solvent Based
- For Use On
- Wood, Masonry, Plaster, Cement
- Application Method
- Brush, Roller, Spray
- Standard / Ready Mixed
- VOC Levels
- Ultra-Low (5-49 g/l)
- Single, Two or Three Pack
- Pack Size
- 1L, 2.5L
- Dry to Recoat (at 20°C)
- 4 Hours
- 13m² per litre
- Recommended Thinner/Cleaner
- Touch Dry
- 1-2 Hours
- UN Number
Be the first to ask a question about this product!
Blackfriar Multi-Surface Primer has been specially formulated to prime multiple surfaces prior to further painting. It’s ideal for hard and soft woods, chipboard, plywood, GRP, MDF, exterior UPVC, ceramic tiles, iron, steel, galvanised and non-ferrous metals (aluminium, brass, chrome, copper) and old plaster. Product Features Interior and...
Blackfriar Patent Knotting solution seals and prevents seepage from knots and resinous areas on timber. For use on interior and exterior bare or stripped wood. Product Features Interior and exterior use. Seals knots. Prevents seepage. Translucent amber solution. Use only under opaque coatings.