Teamac Teamacryl Acrylic Primer Sealer Undercoat
  • Teamac Teamacryl Acrylic Primer Sealer Undercoat
  • Teamac Teamacryl Acrylic Primer Sealer Undercoat
  • Teamac Teamacryl Acrylic Primer Sealer Undercoat

Teamac Teamacryl Acrylic Primer Sealer Undercoat

447/W463/1

Teamac Teamacryl Acrylic Primer Sealer Undercoat, is a water based and low odour paint designed to prime and seal porous surfaces.

Used as a primer/sealer on:

    • Wood
    • Hardboard
    • Blockboard
    • Plaster
    • Masonry
    • Most absorbent surfaces

Click to jump down to Technical Data

Colour
Size
£21.83
VAT excluded

£26.20 Tax incl.
Quantity

Description

Teamac Teamacryl Acrylic Primer Sealer Undercoat, is a water based and low odour paint designed to prime and seal porous surfaces.



Click To Jump To Section:




Features & Benefits


Used as a primer/sealer on:

    • Wood
    • Hardboard
    • Blockboard
    • Plaster
    • Masonry
    • Most absorbent surfaces

Click to jump down to Technical Data



Product Specification


Technical Data
Volume Solids 33%
VOC Content Max 30 g/litre
SG 1.33 @ 20 °C
Viscostity 2.5 @ 25 °C
Flash Point Non-flammable



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Maximum 35 to 40 μm 75 μm 13 m2/litre @ 35 micron D.F.T.



The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.



Drying Times


Drying Times At 20°C/RH 50%
Touch Dry: 30 Mins
Dry To Handle: 2 Hours
Dry To Recoat: 6 Hours
Fully Cured: 5 - 7 Days



Low temperature and high humidity will adversely affect application, drying and performance of any coating.



Surface Preparation


  • All surfaces should be clean, dry, sound and free from contaminants.
  • New wood should be sanded prior to coating to ensure an adequate "key" is produced.
  • Existing painted surfaces should be cleaned, degreased and sanded to ensure an adequate "key" is produced.
  • Remove all loose, flaking material and treat bare areas as new substrate then prepare accordingly.



Preceeding Coat


  • N/A



Subsequent Coat


  • Suitable topcoat.



Mixing


  • Mix well before use.



Application Conditions


  • As dictated by normal good painting practice.
  • In confined spaces, provide adequate ventilation during application and drying.
  • Do not paint when temperature will be at or below 7 °C during the painting and drying process.



Application Methods


Method Airless Spray Conventional Spray Brush Roller
  No No Yes No



  • Thinner (Max vol): Clean Water (10%)
  • Nozzle size: N/A
  • Nozzle pressure: N/A
  • Cleaning solvent: Clean Water



Health & Safety


See safety data sheet - SDS 10634 in the attachments section above.

Click to go back to the top of the page

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
447/W463/1

Data sheet

Manufacturer
Teamac
Base Type
Water
Touch Dry (at 20°C)
30 Mins
Dry to Handle (at 20°C)
2 Hours
Dry to Recoat (at 20°C)
6 hours
Fully Cured (at 20°C)
5 - 7 Days
Coverage
13 sq.m / litre
Min. Application Temperature
Do not paint when temperature will be at or below 7 °C during the painting and drying process.
Solids by Volume
33%
VOC
Max 30 g / litre
Finish
Matt
Size
0.5 litre, 1 litre, 2.5 litre, 5 litre
Recommended Dry Film Thickness
35 to 40
Recommended Wet Film Thickness
75
UN Number
Not regulated
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send