HMG Contract Matt Emulsion

    DEC301
    HMG4544

    HMG Contract Matt Emulsion is a water-based decorative trade matt emulsion that has excellent opacity that improves as the paint dries.

    • Excellent results can be achieved with a single coat.
    • Designed for easy application on interior plaster walls and ceilings.

    Colour
    Size
    Finish
    £53.09(ex. VAT)
    £63.71 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    HMG Contract Matt Emulsion is a water-based decorative trade matt emulsion that has excellent opacity that improves as the paint dries.



    Click To Jump To Section:




    Features & Benefits


    • Excellent results can be achieved with a single coat.
    • Designed for easy application on interior plaster walls and ceilings.



    Product Specification


    Technical Data
    HMG Contract Matt Emulsion WhiteHMG Contract Matt Emulsion Magnolia
    Volume Solids:44.2%44.3%
    VOC Content:0.005kgs/ltr0.005kgs/ltr
    SG:--
    Viscosity:13,700 mPas1,300,000 mPas
    Density:1.353 g/cm³1.354 g/cm³
    Storage Conditions:Store between 5°C - 25°C. When not in use, cans must be kept sealed.Store between 5°C - 25°C. When not in use, cans must be kept sealed.
    Shelf Life:12 months from delivery date in original sealed containers.12 months from delivery date in original sealed containers.
    Pot Life:--
    Flash Point:n/an/a



    Film Thickness Range And Coverage


    Product Data
     Dry Film ThicknessWet Film Thickness
    Brush25μm65μm
    Roller25μm65μm
    HVLP25μm65μm
    Airless/Air-Assisted25μm65μm



    Coverage: 15 square metres per litre @ 25 microns dft.

    • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
    • These values are a guide only and are not to be used as specifications.
    • Film thickness will vary depending on actual use and specification.
    • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



    Drying Times


    Drying Times At 20°C
    Touch Dry:1 hour
    Dry To Recoat:4 hours minimum
    Fully Cured:24 hours



    Surface Preparation


    • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
    • Read and follow the safety data sheet, product data sheet and label instructions.
    • Stir all paints thoroughly before use.
    • Always use the same batch number on the same job.
    • Check colour & sheen.
    • Filter the product immediately before use.
    • Reduce emissions and maintain quality by replacing tin lid after use.



    Application Methods


    Technical Data
    BrushRollerBrushRoller
    Mixing Ratio:Ready for useReady for useBase: 5ltrBase: 5ltr
    --Thinner: >10%Thinner: >10%
    Thinner Options:--WaterWater
    Viscosity:As suppliedAs supplied--
    Spray Gun Setup:--Tip size 0.38mm Tip angle 65° Max press 138barTip size 0.38mm Tip angle 65° Max press 138bar
    Number Of Coats (Guide Only):1 - 2 coats1 - 2 coats1 - 2 coats1 - 2 coats
    Flash Off:----



    For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



    Product Notes


    Information On Basic Physical And Chemical Properties
    HMG Contract Matt Emulsion WhiteHMG Contract Matt Emulsion Magnolia
    Form:According to product specificationAccording to product specification
    Colour:According to product specificationAccording to product specification
    Odour:CharacteristicCharacteristic
    Odour Threshold:Not determinedNot determined
    pH-value 20°C:7.9Not determined
    Melting point/freezing point:UndeterminedUndetermined
    Initial boiling point and boiling range:100°C100°C
    Flash Point:Not applicableNot applicable
    Flammability (solid, gas):Not applicableNot applicable
    Ignition temperature:--
    Decomposition temperature:Not determined.Not determined.
    Auto-ignition temperature:Product is not selfigniting.Product is not selfigniting.
    Explosive properties:"Product is not explosive. However, formation of explosive air vapour mixtures are possible.""Product is not explosive. However, formation of explosive air vapour mixtures are possible."
    Explosion limits: Lower:Not determinedNot determined
    Explosion limits: Upper:Not determinedNot determined
    Vapour pressure at 20°C:23 hPa23 hPa
    Density at 20°C:1.353 g/cm³1.354 g/cm³
    Relative density:Not determinedNot determined
    Vapour density:Not determinedNot determined
    Evaporation rate:Not determinedNot determined
    Solubility in / Miscibility with water:Fully miscibleFully miscible
    Partition coefficient: n-octanol/water:Not determinedNot determined
    Viscosity: Dynamic at 20°C:13,700 mPas1,300,000 mPas
    Viscosity: Kinematic:Not determinedNot determined
    Solvent content: Organic solvents:0.7% - Water: 54.6%0.2% - Water: 54.5%
    Solids content:44.2%44.3%



    Health & Safety


    • Refer to the safety data sheets in the attachments section above and tin label prior to use.

    Click to go back to the top of the page

    Product Details
    4544-720693

    Data sheet

    Manufacturer
    HMG Paints Limited
    Interior / Exterior Use
    Interior Use
    Single, Two or Three Pack
    Single
    Touch Dry (at 20°C)
    1 hour
    Dry to Recoat (at 20°C)
    4 hours minimum
    Fully Cured (at 20°C)
    24 hours
    Density
    HMG Contract Matt Emulsion White: 1.353 g/cm³ - HMG Contract Matt Emulsion Magnolia: 1.354 g/cm³
    Solids by Volume
    HMG Contract Matt Emulsion White: 44.2% - HMG Contract Matt Emulsion Magnolia: 44.3%
    Finish
    Matt
    Size
    10L
    Recommended Dry Film Thickness
    25μm
    Recommended Wet Film Thickness
    65μm
    Base Type
    Water-Based
    Suitable For Use On
    Plaster Walls
    Suitable For Use On
    Plaster Ceilings
    Finish
    Matt
    Product Usage Type
    Topcoat
    Colour Family
    White
    Colour Family
    Magnolia
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    HMG Contract Matt Emulsion is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT