HMG Vinyl Matt Emulsion

DEC101

HMG Vinyl Matt Emulsion is a premium quality water-based, flat matt emulsion.

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
Size
Finish
£20.72
VAT excluded

£24.86 Tax incl.
Quantity

Description

HMG Vinyl Matt Emulsion is a premium quality water-based, flat matt emulsion.



Click To Jump To Section:




Features & Benefits


  • For interior use on wall and ceiling surfaces, where a flat non-reflective finish is required



Product Specification


Technical Data
HMG Vinyl Matt Emulsion White HMG Vinyl Matt Emulsion Colours
Volume Solids: 49.6 % 19.4 %
VOC Content: 0.005 Kg/l 0.005 Kg/l
SG: - -
Viscosity: 11,000 mPas 1,000 mPas
Density: 1.378 g/cm³ 1.045 g/cm³
Storage Conditions: Store between 5°C - 25°C. When not in use, cans must be kept sealed. Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers. 12 months from delivery date in original sealed containers.
Pot Life: - -
Flash Point: n/a n/a



Film Thickness Range And Coverage



Product Data
  Dry Film Thickness Wet Film Thickness
Brush 25 μm 65 μm
Roller 25 μm 65 μm
HVLP 25 μm 65 μm
Airless/Air-Assisted 25 μm 65 μm



Coverage: 15 square metres per litre at 25 microns dft (Theoretical)

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C
Touch Dry: 1 hour
Dry To Recoat: 4 hours minimum
Fully Cured: 24 hours



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
  • Read and follow the safety data sheet, product data sheet and label instructions.
  • Stir all paints thoroughly before use.
  • Always use the same batch number on the same job.
  • Check colour & sheen.
  • Filter the product immediately before use.
  • Reduce emissions and maintain quality by replacing tin lid after use.



Application Methods


Technical Data
Brush Roller HVLP Airless/Air-Assisted
Mixing Ratio: Ready for use Ready for use Base: 5ltr Base: 5ltr
- - Thinner: >10% Thinner: >10%
Thinner Options: - - Water Water
Viscosity: As supplied As supplied - -
Spray Gun Setup: - - Tip size 0.38mm Tip angle 65° Max press 138bar Tip size 0.38mm Tip angle 65° Max press 138bar
Number Of Coats (Guide Only): 1 - 2 coats 1 - 2 coats 1 - 2 coats 1 - 2 coats
Flash Off: - - - -



For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



Product Notes



Information On Basic Physical And Chemical Properties
HMG Vinyl Matt Emulsion White HMG Vinyl Matt Emulsion Colours
Form: According to product specification According to product specification
Colour: According to product specification According to product specification
Odour: Characteristic Characteristic
Odour Threshold: Not determined Not determined
pH-value 20°C: 8.3 8
Melting point/freezing point: Undetermined Undetermined
Initial boiling point and boiling range: 100°C 100°C
Flash Point: n/a n/a
Flammability (solid, gas): Not applicable Not applicable
Ignition temperature: - 370°C
Decomposition temperature: Not determined. Not determined.
Auto-ignition temperature: Product is not selfigniting. Product is not selfigniting.
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible." "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: Not determined Not determined
Explosion limits: Upper: Not determined Not determined
Vapour pressure at 20°C: 23 hPa 23 hPa
Density at 20°C: 1.378 g/cm³ 1.045 g/cm³
Relative density: Not determined Not determined
Vapour density: Not determined Not determined
Evaporation rate: Not determined Not determined
Solubility in / Miscibility with water: Fully miscible Fully miscible
Partition coefficient: n-octanol/water: Not determined Not determined
Viscosity: Dynamic at 20°C: 11,000 mPas 1,000 mPas
Viscosity: Kinematic: Not determined Not determined
Solvent content: Organic solvents: 0.6% - Water: 48.9 % 1.7% - Water: 76.2 %
Solids content: 49.6% 19.4%



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.

Click to go back to the top of the page

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
DEC101

Data sheet

Manufacturer
HMG Paints Limited
Water / Solvent Based
Water
Application Method
Brush, Roller, Spray, Airless Spray
Sheen
Matt
Colour
Standard / Ready Mixed, Fully Tintable
VOC Levels
Low (50-149 g/l)
Single, Two or Three Pack
Single
Pack Size
2.5L, 5L, 10L
Suitable Substrates
Wall and ceiling surfaces
Touch Dry (at 20°C)
1 hour
Dry to Recoat (at 20°C)
4 hours minimum
Fully Cured (at 20°C)
24 hours
Density
HMG Vinyl Matt Emulsion White: 1.378 g/cm³ - HMG Vinyl Matt Emulsion Colours: 1.045 g/cm³
Solids by Volume
HMG Vinyl Matt Emulsion White: 49.6% - HMG Vinyl Matt Emulsion Colours: 19.4%
Recommended Dry Film Thickness
25μm
Recommended Wet Film Thickness
65μm
UN Number
Not regulated
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send