"

Zeroflame Fire Retardant Treatment

Zeroflame Fire Retardant Treatment View larger
Typical Coverage (per coat)3.7m² per litre
Touch Dry1 hour
ApplicationBrush, Roller, Spray
The figures stated above are approximate. Please ensure you refer to all datasheets for full application information.

Zeroflame Fire Retardant Treatment is a clear solution that soaks into the surface to leave the appearance of the timber aesthetically unchanged, achieving British Standard Class 0 (Euroclass B) Fire Protection and Spread of Flame on solid timber. It can be used inside or out and the fire protection remains effective for the lifetime of the wood surface.

Read Full Description

More details

£133.49 + VAT

Fire Retardant Treatment For Wood and Timber

Zeroflame Fire Retardant Treatment is a clear solution that soaks into the surface to leave the appearance of the timber aesthetically unchanged. Applied by brush, roller or spray it achieves British Standard Class 0 (Euroclass B) Fire Protection and Spread of Flame on solid timber. Zeroflame Fire Retardant Treatment can be used inside or out and the fire protection remains effective for the lifetime of the wood surface.

Zeroflame Fire Retardant Treatment soaks into the woods surface, sealing the wood but without leaving a clear glaze on top like a varnish. It then dries with virtually no evidence of the wood ever been treated, allowing you to keep the woods natural beauty and allows you to overcoat the timber with most good quality wood stains and varnishes!

Zeroflame's Fire Resistant Products

Find out more about other fire retardant paints, varnishes and intumescent coatings from Zeroflame here, all available at Rawlins Paints.

The Basics

What you really need to know...

  • Apply 3 coats leaving 40-60mins between coats, each 5lt tin will cover a total of 18.5m² (i.e. if you have an area of 18.5m2 to protect, you will only need 1 x 5lt - there is enough in each 5lt to do the 3 coats)
  • Protects internal & external timber to British Standard Class 0 & Class 1
  • Leaves a colourless finish that doesn't change the surface of the wood, similar to a wood preserver.
  • Can be applied to bare timber and can be overcoated by most wood stains or varnishes.
  • Can be applied with a brush, roller or spray gun.
  • Full certification is issued with every purchase.
  • Fully tested and approved to British Standards.
  • Works by insulating the timber from heat, retarding ignition and stopping the flame from spreading across the surface.

Application Areas

Zeroflame Fire Retardant Treatment is a fire retardant system for the fire protection of hardwoods, softwoods and other cellulose based substrates.

Zeroflame Fire Retardant Treatment treated timber must only be used above the Damp Proof Course level and/or above ground contact. Trials should be carried out on decorative timber species to check any shade changes prior to the full application of the Treatment.

Zeroflame Fire Retardant Treatment Advantages

  • Moisture resistant and unaffected by humidity
  • Suitable for interior and exterior use
  • Unaffected by wear
  • Simple specification
  • Suitable for non-specialist application
  • Suitable for off-site application
  • Applicable by brush, roller or spray
  • Non-toxic and non-allergic
  • Biologically and ecologically safe
  • Colourless and odourless
  • Non-leaching
  • Maintenance free
  • Does not require over coating except for decoration
  • Certificate application included with each container

Un-Matched Performance

To say that Zeroflame Fire Retardant Treatment is revolutionary is an understatement, this remarkable product will protect timber substrates to British Standard Class 0 certification standard, can be used internally and externally, is not affected by moisture when dry, is non-toxic and non-allergic, the list goes on! Never before has there been such a simple product to use for the protection of timber against fire.

Send us your question

Question

Hi, Can Zero Flame be used on cedar cladding to achieve Building Regs requirements for non combustible materials on Dormer roof structures? If so, does the product need to be applied to both sides of the cladding (i.e inner and outer faces)? and would the product effect the natural weathering of cedar cladding over time if applied to outer faces? Thanks

Dave Budworth from Bristol (Uk) - 29/03/17

Answer

Zeroflame Fire Retardant Treatment achieves Euroclass B (BS Class 0) Fire Propagation and Spread of Flame fire protection on solid timber. You will need to refer to your authority to ensure this is the level of fire protection they are expecting you to achieve. Due to it being a Surface Spread of Flame rating usually only the sides exposed to fire would need to be treated. Finally, this product would NOT stop or affect the natural weathering process of the wood.

Hi could you please tell me if your products have undergone third party testing and if so by whom??It's just your product has been specified for a Building Regulation application and we need to know if it's been testedMany thanks

graham walsgrove from winchester (england) - 15/03/17

We have sent copies of the test data to your email address.

Would this be suitable for a fire surround/mantle? The fire Stove sides will be 100-120 mm from the upright beams. So need some kind of retardant to resist heat!

Michael from Brighton and Hove (England) - 24/11/16

Zeroflame Fire Retardant Treatment would certainly increase fire resistance of the timber surrounding your fire but it can't be used as a substitute for the correct installation and required distances of your fireplace.

We have written an extensive article on Painting the Walls around a Fireplace or Multi Fuel Stove which can be found HERE.

will this product fireproof building felt if not any ideas would be helpful Regards Roger

roger lister from cambridge (england) - 21/07/16

No, Zeroflame Fire Retardant Treatment cannot be used on felt. Rust-Oleum Mathys Dacfill HZ has an external fire exposure roof test to BS 476: Part 3: 2004 and achieved EXT.F.AC

I am having 6 solid pine doors dipped back to bare wood. I need the door to be fire retardant up to 20 minutes. Is this product suitable. Thanks

Vicky from Eastbourne (UK) - 18/07/16

Zeroflame Fire Retardant Treatment provides surface spread of flame protection but does not provide fire resistance for 20, 30 or 60 minutes protection so would not be suitable. The product that would be suitable is Fire Door Varnish (30min), this upgrades normal timber flat panel, raised and fielded and ledged and braced doors to 30 minute fire resistance. Each pack contains sufficient primer, intumescent varnish and topcoat (available in clear matt, satin or gloss finishes) to upgrade 4 door sides (including architrave and frame).

Hi can zero flame be applied ontop of a impregnation fluid to a log cabin

DEB from BRISTOL (UK) - 16/07/16

Zeroflame Fire Retardant Treatment can be applied to pressure treated timber as long as the fluid used was water based.

Does Zeroflame Fire Retardant Treatment need to be applied to bare wood in order for it to be effective?

Wayne Lovelock from Coventry (England ) - 25/01/16

Yes it does, it is designed for bare softwood and hardwood and relies on penetrating into the wood. It will only achieve BS Class 1 on veneer and plywood laminates due to the bonding glues hindering penetration. Zeroflame Fire Retardant Treatment also is not suitable for wood-derived particle boards or similar such as MDF and OSB due to it not being absorbent enough.

Could Zeroflame Fire Retardant Treatment be used on top of painted, unsealed timber or would the wood need to be sanded back first? Second, could you paint over the top once applied rather than applying stain/varnish?

Jonathan cooper from Cheltenham (England) - 23/01/16

Zeroflame Fire Retardant Treatment is a penetrative fluid that must be applied to porous, bare timber in order for it to soak in to the wood to be effective. It is not suitable for application over any previous coatings, these must be removed by stripping or sanding prior to application. Once Zeroflame Fire Retardant Treatment has been applied and allowed to sufficiently dry (usually around 7 days), you may apply certain stains, varnishes and paints for decoration purposes (contact our Technical Department for details of coatings that are suitable).

Is Zeroflame Fire Retardant Treatment suitable for use on Bamboo? This is for use in a hotel.

Rob Smith from North Yorkshire (North Yorkshire) - 08/01/16

It isn't, but we do have a clear varnish system that is. Please contact our Technical Department on 0113 2455450 for details.

Hi, we've just made some large flowers (out of willow withies, lantern tissue and pva) for decor to go inside a marquee at Glastonbury, can you tell us if Zeroflame Fire Retardant Treatment would be suitable to coat them with as a fire retardant?

Robert Jakes from Pembroke (UK) - 03/06/15

No, the Zeroflame Fire Retardant Treatment would not be suitable but our 1012 Fire Retardant Solution would be.

Question about the product

I have read and agree to the Conditions of Use (read) Send

The question has been correctly sent

Free delivery on orders over £75 (terms & conditions)

• Deliveries will be made within 3 working days (standard delivery)
• You must be UK mainland based for the free delivery offer.
• Postcodes listed are excluded from the free delivery and priced below.

Please note: deliveries will need to be signed for at the point of delivery.

UK Mainland OnlyUp to £75.00£75.01 +
Standard (2/3 working days)£8.00FREE
Next Day£15.00£15.00
Next day before 09:00am£30.00£30.00
Next day before 10:30am£25.00£25.00
Next day before 12:00pm£20.00£20.00
Saturday Delivery£35.00£35.00














£25 (Standard 2-3 Day Delivery Only)

AB30, AB31, AB32, AB33, AB34, AB35, AB36, AB37, AB38, AB44, AB45, AB46, AB47, AB48, AB49, AB50, AB51, AB52, AB53, AB54, AB55, AB56, FK, G83, IV, KW1, KW2, KW3, KW4, KW5, KW6, KW7, KW8, KW9, KW10, KW11, KW12, KW13, KW14, PA, PH, HS, KA27, KA28, ZE

£35 (Standard 2-3 Day Delivery Only)

BT, IM

£50 (Standard 2-3 Day Delivery Only)

JE, GY

Please note that all carriage prices are quoted without V.A.T. at the current rate.

Scottish Islands - outside standard distribution area, please contact us for a quote.

There may be an exception for heavy goods when purchased in quantity where we will contact you to advise any additional charges.

Next Day delivery and Saturday Service is available on stocked items for orders received before 11:00am only.

Because of the nature of our products, we use specially selected carriers to ensure safe and prompt delivery to you.

Please note: Any time or date named by Rawlins Paints Limited for delivery is given and intended as an estimate only and Rawlins Paints Limited shall not be liable to make good any damage or loss whether arising directly or indirectly out of a delay in delivery. Deliveries are made using a reliable nationwide carrier. Although over 99% of consignments arrive on time, we recommend that no labour is employed to undertake work until materials have arrived on site.

Zeroflame FR Treatment TDS

Download

Zeroflame FR Treatment MSDS

Download
IMPORTANT
Whilst every effort is made to ensure our data sheets are up to date, we advise you check the latest revision directly with the manufacturer to ensure you have the most current version.
E J Rawlins & Co. Ltd trading as Rawlins Paints make available product data sheets and information in good faith but without warranty. We do not accept liability for any errors or omissions contained within the data sheets or any outdated versions.