A single pack, polyurethane enhanced floor coating with 4,400 colours for direct use on concrete floors, wooden floors and masonry inside and out. Offers good protection and is very easy to apply.
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Rust-Oleum 7200 Floorcoat PU is a single pack easy to apply solvent based urethane modified alkyd floor coating specially designed for applying on dry concrete, wood and masonry for interior and exterior use. Rust-Oleum 7200 Floorcoat PU is also ideal as a line marking product, the coating has a good resistance against abrasion and neutral detergents (no alkaline cleaning agents) and is resistant during short contact periods against lubricating oils, fuel, petrol etc.
Rust-Oleum 7200 Floorcoat PU can be applied directly on concrete floors, wooden floors and masonry which are completely clean and dry. It is not recommended to apply on smooth/dense concrete or concrete containing a damp repellent additive, which will prevent a good adhesion. Rust-Oleum 7200 Floorcoat PU can also be applied on old good adhering coatings and can also be applied onto metal floors which have been correctly prepared and primed with a suitable Rust-Oleum metal primer.
Product Advantages:
Can Be Used For:
Preparation:
To ensure homogeneity, coating materials should be thoroughly stirred prior to use. Remove oil, grease and other contamination with Rust-Oleum Mathys ND14 Cleaner Degreaser or high pressure (steam) cleaning in combination with appropriate detergents. Sand old intact coatings to roughen the surface in order to establish a good adhesion. Check the compatibility with old intact coatings. During application the surface should be dry and clean. On porous concrete a first coat should be applied with Rust-Oleum 7200 Floorcoat PU diluted with ±5% Rust-Oleum Thinner 633. On new concrete (>28 days) use Rust-Oleum 7201 Universal Floor Primer as a first coat or use Rust-Oleum Mathys 108 Surfa Etch Solution to neutralise any remaining alkalinity from the cement. Remove curing compounds by means of dust free blasting.
Application & Thinning:
Application Conditions:
Apply in a dry and well-ventilated area. Do not apply Rust-Oleum 7200 Floorcoat PU on alkaline substrates, or in areas which will be constantly under water.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
 Andy Parkes on 2023-09-12 10:24:51 | Question: Hi. Is this product suitable for painting on old fashioned exterior 2' x 3' concrete paving slabs? Foot traffic only. Intended to lay between decorative gravel. Thanks AP |
Answer from Rawlins’ Technical Team: Assuming the is a damp proof membrane present below the slabs, they are clean, dry, sound and prepared as detailed in the technical data sheet this could be used. The slabs will need to be etched prior to application with Rust-Oleum Mathys 108 Surfa Etch Solution. | |
| andi stevenson on 2023-09-09 03:21:31 | Question: Can this be used on stone walls? |
Answer from Rawlins’ Technical Team: This product is designed for use on concrete floors, wooden floors and masonry internally and externally. If you could e-mail your requirements to [email protected] , we maybe able to offer a better suited product for your application type. | |
| Richard Curant on 2023-07-23 09:04:19 | Question: Hi will this adhere to floor levelling compound (like hard plaster). Thanks Richard |
Answer from Rawlins’ Technical Team: On the assumption that the compound is cementitious, smooth and non-porous, ensure the surface is suitably prepared as detailed in the Technical Data Sheet prior to application of this product. Depending on the total surface area, this may be achieved by either blasting or grinding of the surface, or via etching the surface with Rust-Oleum Mathys 108 Surfa Etch Solution before applying Rust-Oleum 7200 Floorcoat PU. This can be mixed to many RAL, NCS or BS colours in a satin or gloss finish. | |
| Mariusz on 2023-05-03 07:12:25 | Question: good morning, I bought Rust-Oleum paint 7200 PU and painted new and very well washed garden tiles with it and after a few weeks there are places where the paint peels off and I don't know how to save it now. Can I paint these places with one more layer? And can I generally paint this paint with one more layer with a different color, because I am not satisfied with the color either. |
Answer from Rawlins’ Technical Team: We are sorry to hear of the issue you are having with the paint, we have contacted you directly by email to look into this. | |
| Katie on 2022-10-05 15:46:26 | Question: Is this suitable for painting on ceramic floor tiles? If so, what primer would you recommend to use with it? Thanks |
Answer from Rawlins’ Technical Team: Unfortunately no, assuming the ceramic tiles are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Protectakote Clear Primer Treatment follow by Smartkote Protectakote UVR Smooth. This is available in black, white or clear in a gloss finish. | |
| Juliet on 2022-09-23 17:34:52 | Question: Can this be used to paint over vinyl floor tiles (such as Karndean)? |
Answer from Rawlins’ Technical Team: Unfortunately no. Assuming the vinyl floor tiles are a linoleum or rubber, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Protectakote UVR Smooth. This is available in black, white or clear in a gloss finish. The floor must be sanded and cleaning with 100 Rapid Drying Thinner prior to application. | |
| Brian Moles on 2022-09-03 14:06:28 | Question: Hi, would this be suitable for a high traffic internal patio door sill/threshold? |
Answer from Rawlins’ Technical Team: Assuming the door threshold is bare timber, it is clean, dry, sound and prepared as detailed in the technical data sheet it could be used. As this is a high traffic area it may require reapplication when signs of wear occur. | |
| Katerina on 2022-08-03 14:38:41 | Question: Can you paint a second coat a week after the first? |
Answer from Rawlins’ Technical Team: We would recommend applying a second coat within 7 days. As this paint is fully cured in 1 week, to apply a further coat after this time you will need to sand the floor to provide a key and make sure the floor is clean, dry and sound prior to application. | |
| Phil ward on 2022-06-23 13:41:08 | Question: Is the paint suitable to cover imprinted concrete driveway. |
Answer from Rawlins’ Technical Team: No, unfortunately we do not have a product to recommend for painting an imprinted concrete driveway. | |
| GABRIEL on 2022-05-17 07:22:18 | Question: Hi, I need to paint my concrete patio slabs. Considering that it's an outdoor surface, Is this the right product to use on those? Thanks! |
Answer from Rawlins’ Technical Team: Assuming there is a damp proof membrane present below the slabs, they are not subject to vehicle traffic, they are bare, clean, dry, sound and prepared as detailed in the technical data sheet, this could be used. We would recommend you test for compatibility and adhesion prior to full application. | |
| J.mcathey on 2021-06-18 10:14:12 | Question: How long is the guarantee under normal patio conditions. |
Answer from Rawlins’ Technical Team: Thank you for the enquiry, there is no guarantee offered with this product, but it is suitable for domestic levels of foot traffic when applied to a compatible, prepared substrate. | |
Rust-Oleum 7200 Floorcoat PU is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
A specially formulated blend of solvents designed to mix with its compatible Rust-Oleum coating to create an optimal consistancy for application whether it be for Brush, Roller or Spray.Can also be used for the cleaning of some surfaces prior to application of the coating Suitable for cleaning of the application tools such as Brushes,...
£74.34 (incl. VAT)
£61.95 (ex. VAT)
Rust-Oleum Mathys 108 Surfa Etch Solution is an easy to use, non-flammable and virtually odour free etching solution for the preparation of smooth concrete surfaces, masonry, galvanized steel and aluminum before applying a paint coating system.Improves the adhesion of coating systems Neutralizes alkaline salts Also ideal to remove "white...
£67.06 (incl. VAT)
£55.88 (ex. VAT)
Rust-Oleum Mathys Alkaline Cleaner/Degreaser ND14 should be used to remove grease, oil, proteins, dirt and many other surface contaminants from coated, mineral and steel substrates.Non-flammable, virtually odour-free cleaning/degreasing solution. Can be used as an additive for high pressure and steam cleaning Applied by synthetic sponge,...
£89.78 (incl. VAT)
£74.82 (ex. VAT)
A specially formulated blend of solvents designed to mix with its compatible Rust-Oleum coating to create an optimal consistancy for application whether it be for Brush, Roller or Spray.Can also be used for the cleaning of some surfaces prior to application of the coating Suitable for the cleaning of the application tools such as Brushes,...
£15.54 (incl. VAT)
£12.95 (ex. VAT)
Floor Application Kit from Rawlins Paints provides all the application equipment needed to apply conventional floor paints and coatings to a professional standard. The application of floor coatings is often crucial to their performance, so it is important to use the right tools to ensure a lasting finish.Each kit contains:12" Roller,...
£101.58 (incl. VAT)
£84.65 (ex. VAT)
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. Rust-Oleum 7201 Universal Floor Primer is ready for use solvent based adhesion primer based on a special epoxyester binder. Improves the adhesion...
Rust-Oleum Non-Skid Additive NS 100 an anti-slip HDPE granulate that turns a standard floor coating into a durable anti-slip coating. It is intended to be added to 1K floor paint to produce a subtle non-skid surface, that is easier to clean than coarse anti-slip floors.Smaller size granules for more subtle anti-slip finish Designed for...
£7.94 (incl. VAT)
£6.62 (ex. VAT)
