"

Rust-Oleum Mathys Pegakote

Rust-Oleum Mathys Pegakote View larger
Typical Coverage (per coat)3.25m² per kg
Touch Dry9 Hours
ApplicationBrush, Roller, Spray
The figures stated above are approximate. Please ensure you refer to all datasheets for full application information.

Rust-Oleum Mathys Pegakote is a two-pack, water based, epoxy coating for interior floor and wall surfaces in garages, warehouses, showrooms, corridors, indoor car parks, workshops, etc. It is solvent free, almost odourless and easy to clean leaving a smooth, stain finish and can also be used as a self levelling coating with a thickness of up to 3mm.

Read Full Description

More details

£39.96 + VAT

Rust-Oleum Mathys Pegakote is a two-pack, water based, epoxy coating for interior floor and wall surfaces in garages, warehouses, showrooms, corridors, indoor car parks, workshops, etc. Rust-Oleum Mathys Pegakote dries to a very hard finish which provides exceptional abrasion resistance (Taber Abrasion weight loss after 1000 cycles: ± 60 mg (CS10, load: 1000g)) and is resistant to oils and solvents. It is solvent free, almost odourless and easy to clean leaving a smooth, stain finish and can also be used as a self levelling coating with a thickness of up to 3mm.

Features & Benefits

  • Exceptionally abrasion resistant
  • Smooth satin gloss finish in almost any colour
  • Easy to apply and clean
  • Resistant to oils and solvents
  • Water-based, very low odour

Surface Preparation
The substrate should be dry and clean, free from ascending humidity and sufficiently coherent (tensile strength min. 6kg/cm²). Rust-Oleum Mathys Pegakote can be applied directly on most mineral substrates (for instance old concrete, tiles, glass etc.). Curing compounds in case of poly-concrete have to be removed by means of sand or grit blasting. On new concrete or non-porous concrete, remove cement grout by sand or grit blasting, treatment with diluted hydrochloric acid at a ratio of 3 litres hydrochloric acid to 10 litres water or with Rust-Oleum Mathys 108 Surfa Etch Solution. For these two last solutions, there is obligation to rinse abundantly and to allow drying through of the surfaces. Porous substrates shall be impregnated with Rust-Oleum Mathys Pegakote diluted with 10-20% water. Rust-Oleum Mathys Pegakote may not be applied on an elastic paint coat or a moving substrate.

Directions for Use
To ensure homogeneity, coating materials should be thoroughly stirred prior to use. Stir the activator thoroughly using an electrical mixer at low speed. Add progressively under stirring to the base. Stir the mixture thoroughly until an even colour and consistency are obtained during minimum 3 minutes. Temperature of the mixed materials should be at least 10°C.

Application & Thinning

  • Brush: If necessary, dilute with water.
  • Roller: Dilute 1st coat with max. 10% water. Apply 2nd coat undiluted.
  • Air-atomised spray: Not recommended.
  • Airless spray: Nozzle: 015 - 017 / Pressure: 220 bars. 1st coat: dilute with 5-10% water. 2nd coat: dilute with max. 5% water.
  • Rake/Trowel: Pour the material onto the properly cleaned floor and spread it out evenly with a rake or a trowel. Treat the surface directly after application with the de-aeration roller to release entrapped air and to promote the self-levelling effect. Maximum DFT: 3mm. When used as a self-leveling coat, drying times will be slower: 24h for foot traffic.

Application Conditions
Minimum 8°C and maximum 80% R.H.

Consumption

Theoretical:

  • 300g/m² for roller and airless applications
  • 3kg/m² when used as a self-levelling product at a thickness of 1mm

Practical: Coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.

Cleaning of Equipment/Spills

Water.

Remarks

  1. In order to become a solid satin finish, please respect the consumption quantities of the second layer, this means that a tin of 4kg has to be applied on a surface of 10–13m².
  2. Always provide good air ventilation; so even when it rains, windows and doors have to be opened wherever possible.
  3. The 2 components must be mixed under mechanical agitation.
  4. For use on floors submitted to heavy abrasion, standard and medium colours are recommended. In case of deep and/or bright tones (red, yellow, orange, green, blue etc), it is advised to apply a clear topcoat such as Rust-Oleum 9200 Rust-O-Thane.
  5. Shelf Life: 2 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 5°C and 35°C.

Drying Times @ 20°C/RH 50%

Touch Dry:9 h
Dry to Handle:12 h
Dry to Recoat:24 h at 20°C, 48 h at 8-10°C
Fully Cured:7 days
Pot Life:2 h

Technical Data

Density:1.45 kg/l
Gloss Level:Satin
Solids Content in Volume:48-50%
Solids Content in Weight:64-66%
Mixing Ratio:Base : Activator = 6.2 : 1 (weight)
Recommended Wet Film Thickness:200µm
Recommended Dry Film Thickness:100µm

Safety Data

VOC Level:0 g/l
VOC Readymix:10 g/l
VOC Category:A/j
VOC Limit:140 g/l
Grenelle:A+
Flashpoint:Not flammable
Remarks Regarding Safety:Consult Safety Data Sheet and Safety Information printed on can.

Send us your question

Question

Can this floor paint be applied over concrete floorings previously covered with an epoxy paint or a polymer resin paint.

chris from north cave (uk) - 16/11/16

Answer

Assuming that the underlying floor substrate is solid with no damages and is not moving in any way, and that the previously (correctly applied and cured) epoxy layer remains in good condition and well adhered to the underlying substrate, then yes Rust-Oleum Mathys Pegakote can be applied on top.

In all instances, the existing surface should be thoroughly degreased using a 5% solution of Rust-Oleum Mathys ND14 Cleaner Degreaser and then sufficiently abraded by the most suitable method (e.g. blasting, grinding, etc.)

We have recently painted Floors in a University with Rustoleum Pegakote and the client is now asking what type of product they should use to clean the floors . Regards, David Ross

Ross & Co from Dingwall (Scotland) - 27/09/16

As a general cleaner we would recommend Rust-Oleum Floor Cleaner.

Can this product be applied directly onto Cementone Cempolay self levelling screed?

Jim Mountain from Saxmundham (Suffolk) - 13/03/16

If you have used the standard Cempolay then this is not strong enough to take an epoxy coating, it is designed to be over laid with vinyl, wood floor, tiles, etc. If you have used Cempolay Ultra Strong, then this is strong enough to take an epoxy floor coating and the Pegakote should be fine to be applied after preparation.

Which of the epoxy paints is most suitable for painting a wet room floor?

Jennifer Holburn from Stirling (Scotland) - 13/12/15

Rust-Oleum 5500 Solvent Free Epoxy would be a good choice assuming the area you have to paint is bare concrete. You might also want to consider adding an anti-slip aggregate into the system for some slip resistance.

Question about the product

I have read and agree to the Conditions of Use (read) Send

The question has been correctly sent

Free delivery on orders over £75 (terms & conditions)

• Deliveries will be made within 3 working days (standard delivery)
• You must be UK mainland based for the free delivery offer.
• Postcodes listed are excluded from the free delivery and priced below.

Please note: deliveries will need to be signed for at the point of delivery.

UK Mainland OnlyUp to £75.00£75.01 +
Standard (2/3 working days)£8.00FREE
Next Day£15.00£15.00
Next day before 09:00am£30.00£30.00
Next day before 10:30am£25.00£25.00
Next day before 12:00pm£20.00£20.00
Saturday Delivery£35.00£35.00














£25 (Standard 2-3 Day Delivery Only)

AB30, AB31, AB32, AB33, AB34, AB35, AB36, AB37, AB38, AB44, AB45, AB46, AB47, AB48, AB49, AB50, AB51, AB52, AB53, AB54, AB55, AB56, FK, G83, IV, KW1, KW2, KW3, KW4, KW5, KW6, KW7, KW8, KW9, KW10, KW11, KW12, KW13, KW14, PA, PH, HS, KA27, KA28, ZE

£35 (Standard 2-3 Day Delivery Only)

BT, IM

£50 (Standard 2-3 Day Delivery Only)

JE, GY

Please note that all carriage prices are quoted without V.A.T. at the current rate.

Scottish Islands - outside standard distribution area, please contact us for a quote.

There may be an exception for heavy goods when purchased in quantity where we will contact you to advise any additional charges.

Next Day delivery and Saturday Service is available on stocked items for orders received before 11:00am only.

Because of the nature of our products, we use specially selected carriers to ensure safe and prompt delivery to you.

Please note: Any time or date named by Rawlins Paints Limited for delivery is given and intended as an estimate only and Rawlins Paints Limited shall not be liable to make good any damage or loss whether arising directly or indirectly out of a delay in delivery. Deliveries are made using a reliable nationwide carrier. Although over 99% of consignments arrive on time, we recommend that no labour is employed to undertake work until materials have arrived on site.

Rust-Oleum Pegakote TDS

Download

Rust-Oleum Pegakote MSDS Base

Download

Rust-Oleum Pegakote MSDS Activator

Download
IMPORTANT
Whilst every effort is made to ensure our data sheets are up to date, we advise you check the latest revision directly with the manufacturer to ensure you have the most current version.
E J Rawlins & Co. Ltd trading as Rawlins Paints make available product data sheets and information in good faith but without warranty. We do not accept liability for any errors or omissions contained within the data sheets or any outdated versions.