Sherwin-Williams Epigrip C400V3 multi-functional epoxy zinc phosphate coating is suitable for the protection of steelwork in a range of exposure environments from C1 to C5 as defined in ISO12944, including buildings, car parks, petrochemical plants, breweries and power stations. Indefinitely overcoatble with Sherwin-Williams epoxy systems.Read Full Description
£38.48 + VAT
This product is not sold individually. You must select at least 1 quantity for this product.
Warning: Last items in stock!
Sherwin-Williams Epigrip C400V3 multi-functional epoxy zinc phosphate coating is suitable for the protection of steelwork in a range of exposure environments from C1 to C5 as defined in ISO12944, including buildings, car parks, petrochemical plants, breweries and power stations.
Sherwin-Williams Epigrip C400V3 is often specified for use as a primer for structural steel on blast cleaned steel for internal and external environments, it may also be used as a high build intermediate coat as well as the final coat where a low sheen industrial and functional finish is required but is not suitable for immersion.
All Epoxy products will lose gloss and colour when exposed in an external environment and so where good colour and gloss retention is required in an external environment, or a full decorative finish is required in an internal environment, one of the Shewrin-Williams topcoats designed specifically for this role should be chosen. A selection of available topcoats is listed below under Recommended Topcoats.
Sherwin-Williams Epigrip C400V3 may be applied between 75 and 275 microns DFT in one coat depending on specification requirements. As many projects will differ in terms of client requirements and exposure environments, detailed project specifications are available from our Technical Team seperately if required.
Indefinitely overcoatable with epoxy systems provided the surfaces to be coated have been suitably cleaned. Where a high degree of gloss and colour retention is required overcoat with Resistex C137V2, Resistex C237, Acrolon 1850 and Acrolon 7300 within 7 days at a minimum dft of 50 microns or in the case of Leighs C750V2 overcoat within 4 days. These overcoating times refer to achievement of optimum adhesion at 23°C and will vary with temperature.
For overcoating with alkyd systems consult our Techincal Team for advice. Overcoatable with Envirogard M770 Water Based Finish within 1 month @ 15°C.
What is the best way to repair/repaint areas of primer damaged by rust etc
Paul Cumming from Dundee (Scotland ) - 12/06/16
Blast clean to Sa2½ BS EN ISO 8501-1:2007. Average surface profile in the range 50-75 microns. Ensure surfaces to be coated are clean, dry and free from all surface contamination. Manually prepared surfaces should be prepared to a minimum standard of St3 BS EN ISO 8501-1:2007 at the time of coating. Application to such surfaces should be by brush or roller where the mechanical action will aid adhesion.
I have lads working / mixing the C400v3 with a hardener additive. I know that the mix is 7/1, but what is the working time once this is mixed, the working temperature is approximately 11/12c ? Also, should a face mask be donned when applying this product ??
Jim Smith from North Uist (Scotland) - 14/03/16
Once correctly mixed you will have an approximate pot life of 2.5 hours @ 15°C. Consult Product Health and Safety Data Sheet for information on safe storage, handling and application of this product which is available to download from the 'DATASHEETS' tab on this product page.
Free delivery on orders over £75 (terms & conditions)
• Deliveries will be made within 3 working days (standard delivery)
• You must be UK mainland based for the free delivery offer.
• Postcodes listed are excluded from the free delivery and priced below.
Please note: deliveries will need to be signed for at the point of delivery.
|UK Mainland Only||Up to £75.00||£75.01 +|
|Standard (2/3 working days)||£8.00||FREE|
|Next day before 09:00am||£30.00||£30.00|
|Next day before 10:30am||£25.00||£25.00|
|Next day before 12:00pm||£20.00||£20.00|
£25 (Standard 2-3 Day Delivery Only)
AB30, AB31, AB32, AB33, AB34, AB35, AB36, AB37, AB38, AB44, AB45, AB46, AB47, AB48, AB49, AB50, AB51, AB52, AB53, AB54, AB55, AB56, FK, G83, IV, KW1, KW2, KW3, KW4, KW5, KW6, KW7, KW8, KW9, KW10, KW11, KW12, KW13, KW14, PA, PH, HS, KA27, KA28, ZE
£35 (Standard 2-3 Day Delivery Only)
£50 (Standard 2-3 Day Delivery Only)
Please note that all carriage prices are quoted without V.A.T. at the current rate.
Scottish Islands - outside standard distribution area, please contact us for a quote.
There may be an exception for heavy goods when purchased in quantity where we will contact you to advise any additional charges.
Next Day delivery and Saturday Service is available on stocked items for orders received before 11:00am only.
Because of the nature of our products, we use specially selected carriers to ensure safe and prompt delivery to you.
Please note: Any time or date named by Rawlins Paints Limited for delivery is given and intended as an estimate only and Rawlins Paints Limited shall not be liable to make good any damage or loss whether arising directly or indirectly out of a delay in delivery. Deliveries are made using a reliable nationwide carrier. Although over 99% of consignments arrive on time, we recommend that no labour is employed to undertake work until materials have arrived on site.