A high performance, fast drying acrylic urethane gloss finish in 450+ colours for use where long term exterior gloss and colour retention characteristics are required.
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Sherwin-Williams Acrolon C137V2 (formerly Resistex C137V2) is a high performance, fast drying acrylic urethane gloss finish for use where long term exterior gloss and colour retention characteristics are required. Acrolon C137V2 is suitable for use as a final coat(s) in conjunction with epoxy or polyurethane based protective systems for new construction or maintenance purposes.
Material is suitable for use as final coat or coats in conjunction with epoxy or polyurethane based protective systems for new construction or maintenance purposes.
Compatible with a wide range of Macropoxy, Dura-plate, Zinc Clad Epoxy Primers and Buildcoats.
Not normally required but indefinitely overcoatable with itself and other high performance topcoats.
Airless Spray
Nozzle Size: 0.33mm (13 thou)
Fan Angle: 65°
Operating Pressure: 210kg/cm² (3000 psi)
The airless spray details given above are intended as a guide only. Details such as fluid hose length and diameter, paint temperature and job shape and size all have an effect on the spray tip and operating pressure chosen. However, the operating pressure should be the lowest possible consistent with satisfactory atomisation. As conditions will vary from job to job, it is the applicators’ responsibility to ensure that the equipment in use has been set up to give the best results. If in doubt Rawlins Paints should be consulted.
Conventional Spray
Nozzle Size: 1.27mm (50 thou)
Atomising Pressure: 3.5kg/cm² (50 psi)
Fluid Pressure: 0.7kg/cm² (10 psi)
The details of atomising pressure, fluid pressure and nozzle size are given as a guide. It may be found that slight variations of pressure will provide optimum atomisation in some circumstances according to the set up in use. Atomising air pressure depends on the air cap in use and the fluid pressure depends on the length of line and direction of feed i.e. horizontal or vertical.
For application by conventional spray thin up to 10% with Cleanser/Thinner No.15. Wet film thickness should be adjusted accordingly.
NB - Thinning will affect VOC compliance.
Brush
The material is suitable for brush application. Application of more than one coat may be necessary to give equivalent dry film thickness to a single spray applied coat.
Roller
The material is suitable for roller application using a short pile roller. Application of more than one coat may be necessary to give equivalent dry film thickness to a single spray applied coat.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
 Suresh .R on 2020-05-18 07:03:33 | Question: What is the gloss level of ACROLON C 137V2, I couldn't able to find in your PDS, please let me know how to check it??? Thanks Suresh.R |
Answer from Rawlins’ Technical Team: This product has a gloss level of approximately 70%. | |
| Jo on 2020-03-04 16:26:38 | Question: I need to stencil a design on exterior walls that are coated with Acrolon. What kind of paint can I use that will stick to that surface? Since it is a glossy surface, if I use Acrolon on Acrolon, will I need to scuff the surface. I f I scuff the surface, could I use basic latex paint? Thanks |
Answer from Rawlins’ Technical Team: Sherwin-Williams Acrolon C137V2 is indefinitely overcoatable with itself so ensure surfaces to be coated are clean, dry and free from all surface contamination. Lightly abrade to provide an adequate key and then apply more Sherwin-Williams Acrolon C137V2 as required. | |
| lee Byrne on 2019-06-07 21:26:22 | Question: can this product be used directly over previously painted steel which is sound and in good condition as a 2 coat finish, or would a primer or undercoat be required. Thanks Lee |
Answer from Rawlins’ Technical Team: It can providing the existing coatings are two pack products and offer the required corrosion protection. In all instances we would recommend a site trial to confirm compatibility. | |
| Paul Foster on 2018-12-14 16:35:45 | Question: What is the expected frequency of application of this product. How long would it be before needs recoating |
Answer from Rawlins’ Technical Team: Expected life depends on the service condition, exposure and colour. Sherwin-Williams Acrolon C137V2 is normally expected to offer a durability of 20 years depending on the system build up. Characteristics such as colour and gloss retention cannot be given a durability. Colours such as grey or black tend to hold better than strong reds, yellows, oranges, etc. Without further information on your requirements, exposure, system build up, etc. the only advise we can offer here is: if it starts to fade, abrade and re-coat. | |
| paul johnston on 2017-08-08 15:29:44 | Question: Can this product be used to paint a concrete floor? It is inside, and will be subject to people walking on it? |
Answer from Rawlins’ Technical Team: No, however if traffic is only foot traffic and relatively light, for internal purposes we would recommend Sherwin-Williams Macropoxy M262, this can also be aggregated with a fine sand, like aggregate P515. | |
Sherwin-Williams Acrolon C137V2 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Sherwin-Williams Cleanser/Thinner No.5 is a specially formulated blend of solvents designed to mix with its compatible Sherwin-Williams products to create an optimal consistency for application whether it be for Brush, Roller or Spray. It can also be used for cleaning of surfaces and application equipment.Specially formulated blend of...
£53.00 (incl. VAT)
£44.17 (ex. VAT)
Sherwin-Williams Cleanser/Thinner No.15 is a specially formulated blend of solvents designed to mix with its compatible Sherwin-Williams products to create an optimal consistency for application whether it be for Brush, Roller or Spray. It can also be used for cleaning of surfaces and application equipment. More Information Delivery Info
£79.15 (incl. VAT)
£65.96 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)
