Rust-Oleum Hard Hat Topcoat is the number 1 industrial paint aerosol, a top quality high performance topcoat for use on bare metal, wood and concrete that is ready to handle after just 30 minutes (at 20°C).
Heat-resistant up to 100°C, Hard Hat Topcoat aerosols can cover up to 2.5 m² per spray can (at 25 μm dry). Recommended for small jobs, spot touch-up and general maintainence, Rust-Oleum Hard Hat Topcoat should be applied over Rust-Oleum Hard Hat 2169/2182 Anti-Rust Primer, or properly prepared painted substrates, and used in light industrial exposures, normal humidity and interior applications.
Features & Benefits
Convenient spray can topcoat for small maintenance jobs or for touch-up
Fast drying short oil soya alkyd - ready to handle in just 30 minutes (at 20°C)
Best available hiding power
Heat-resistant up to 100°C
Based on lead and chromate-free pigments
Up to 2.5 m² coverage per spray can at 25 μm dry
See below for more detailed drying times and technical data
TECHNICAL DATA
Gloss Level:
Gloss
Propellant:
Dimethyl ether
Heat Resistance:
100°C (dry heat), above 65°C discoloration may occur
DRYING TIMES AT 20°C/RH 50%
Touch dry:
15 minutes
Dry to handle:
30 minutes
Dry to recoat:
Within 1 hour or after 48 hours
Fully cured:
7 days
Recommended Wet Film Thickness
100 μm
Recommended Dry Film Thickness
25 μm
Theoretical Consumption
2.5 m² per spray can at 25 μm dry
Practical Consumption
Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.
Surface Preparation
Remove dirt, grease, oil, loose rust and all other surface contaminants by appropriate means. Prime or spot prime with the recommended RUST-OLEUM Primers. Sand intact coatings to provide a proper key for adhesion. The surface must be clean and dry during application.
Application Conditions
For good results the relative humidity shall be below 85% and the temperature of the can above and substrate 0°C.
Remove cover cap. Shake vigorously for at least one minute after the rattle of mixing ball is heard. Shake frequently during use. Hold can approx. 25 cm from surface. Use back and forth motion keeping can parallel with surface. Ensure that can is in motion when spray button is pressed to avoid runs and sags. Apply several thin layers at a few minutes interval to achieve adequate coating thickness. After use turn can upside down and press spray button for 2 - 3 seconds to clean valve.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Rust-Oleum Hard Hat Topcoat - Anthracite Grey is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
Rust-Oleum Hard Hat 2169/2182 Anti-Rust Primer is to be used on new, bare or slightly rusted steel surfaces to prevent further rusting and corrosion. Ready to recoat after just 10 minutes, to handle after 30 min. Penetrates deeply into the surface and does not give rust a chance Grey for light coloured topcoats and red for dark coloured...